1 / 16

Microprocessor based Design for Biomedical Applications MBE 3 – MDBA XI : Project Outlooks

Microprocessor based Design for Biomedical Applications MBE 3 – MDBA XI : Project Outlooks. Resumee of our Project Works (1) We built 4 AVR Evaluation Board Kits and used them for basic firmware projects with the ATmega8 : ● AVR-GCC, make, AVRStudio toolchains

anika
Download Presentation

Microprocessor based Design for Biomedical Applications MBE 3 – MDBA XI : Project Outlooks

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Microprocessor based Design for Biomedical ApplicationsMBE 3 – MDBAXI :Project Outlooks

  2. Resumee of our Project Works (1) We built 4 AVR Evaluation Board Kits and used them for basic firmware projects with the ATmega8 : ●AVR-GCC, make, AVRStudio toolchains ● Firmware download via direct SPI access ● GPIO, Timer Interrupts, ISRs ● UART, Interrupt driven communication ● Analog/Digital Conversion ● Transfer of multiple channels, data packets

  3. Resumee of our Project Works (2) We brought up 4 Monolith-EEGs : ●soldered and debugged the SMD-boards ● soldered the extension boards with SPI connectors ● understood the analog and digtial schematics (nearly ;-) ● ported the firmware to the ATmega168 ● used the FTDI UART-USB converter ICs ● investigated the bootloader-mechansim ● evaluated our designs with realtime EEG / ECG recordings

  4. So I would say : We did a great job ! http://www.aerotraining.com/awards.htm

  5. For sure, this project could be extended. Here come a few ideas ….

  6. Possible Hardware extensions : ● an EEPROMto store configuration data ● battery driven (offline) operation: what batteries / accus ? Stepup converter ? ● wireless communication: add a bluetooth or zigbee module http://www.bluegiga.com/default.asp?f=2&t=1&p=8700&subp=200 ● on-board data-logging: interface with a MMD / SD memory card http://www.ulrichradig.de/home/index.php/avr/mmc-sd ● new sensors: GSR/EDA , temperature, pulse, acceleration .. http://electronicdesign.com/Articles/Index.cfm?AD=1&ArticleID=6343 ● evaluate active (dry) electrodes and alternative electrode caps http://www.dcc.uchile.cl/~peortega/ae/

  7. The Serial Peripheral Interface Miso: master in slave out Mosi: master out slave in SCK: clock SS: slave select

  8. SD / MMC – Interface : SPI - Bus

  9. TWI – The Two Wire Interface (IIC Bus) SDA : serial Data SCL : serial Clock R1, R2 : Pullup Resistors on the Bus lines, devices tri-state their outputs line level goes low if any of the connected device outputs 0 START: SDA goes low during SCL high STOP: SDA goes high during SCL high

  10. TWI – The Two Wire Interface (IIC Bus) ●only two Bus Lines needed for bidirectional communication ● Master and Slave Operation ●Device can Operate as Transmitter or Receiver ●7-bit Address Space Allows up to 128 Different Slave Addresses ●Multi-master Arbitration Support ●Up to 400 kHz Data Transfer Speed ●Noise Suppression Circuitry Rejects Spikes on Bus Lines ●Wake-up when AVR is in sleep mode and slave address detected as ever: the AVR datasheet has the details …

  11. TWI – example: EEPROM interface to AVR http://www.captain.at/electronic-atmega-eeprom.php

  12. Some Ideas for Software extensions …

  13. Possible Software extensions at the uC (firmware) side: ● on-board filtering ( configure FIR / IIR filters for channels ) http://www.atmel.com/dyn/resources/prod_documents/doc2527.pdf ● on-board feature extraction ( pulse rate ? ) ● Bidirectional communication : change baud- and sampling rate at runtime select relevant channels allow access to I/O-pins ( Events ? ERP-recording ? ) error detection / correction for data transfer … some of these features are already present in the p21-firmware: http://people.freenet.de/moosec/projekte/simpleeeg/download/firmware212.zip

  14. Possible Software extensions at the PC (host) side: ● write our own data packet parser ● write a simple biosignal tracing and recording software in a platform independent environment (JAVA? C++ & GTK / QT / SDL ?) ● investigate algorithms for feature extraction (pattern recognition ? LDA / AR-Filter for SSVEP or μ -BCI ?)

  15. BrainBay - extensions Configurations: ● design Biosignal protocols with midi / optical feedback Alpha / Theta Training ? REM-Detection ? Muscle Rehabilitation Training ? Extend / improve the software: ● add new modules ● remove OS-dependent parts ● improve signal handling … http://www.shifz.org/brainbay/manuals/brainbay_developer_manual.pdf

  16. Conclusions: ● This project has lots of potential for future improvements ● in the optimal case, Open Source Projects are a win-win situation I hope you enjoyed the show - have a good time and much Alpha-Activity !

More Related