1 / 26

Suspension Design Part 1

Suspension Design Part 1. Rob Shanahan 11-15-05. Introduction. What is an Automotive Suspension? An Automotive Suspension is the system of parts that give a vehicle the ability to maneuver. It is a 3 Dimensional Four Bar Linkage What does a suspension do?

dlacroix
Download Presentation

Suspension Design Part 1

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Suspension Design Part 1 Rob Shanahan 11-15-05

  2. Introduction • What is an Automotive Suspension? An Automotive Suspension is the system of parts that give a vehicle the ability to maneuver. It is a 3 Dimensional Four Bar Linkage • What does a suspension do? “The job of a car suspension is to maximize the friction between the tires and the road surface, to provide steering stability with good handling” HowStuffWorks.com

  3. Basic Suspension Terminology • Ride Height • Bump / Droop • Camber • Caster • Toe In / Out

  4. Ride Height, Bump & Droop • Ride Height • The neutral / middle position of the Suspension • Bump • When the wheel moves upwards • Droop • When the wheel moves downwards

  5. Camber • Tires generate more cornering force with a small amount of negative camber • Camber changes as suspension moves up (bump) and down (droop)

  6. Caster • Shopping cart action • Causes self-centering action in the steering • More caster results in more camber as front wheels are turned

  7. Toe-in or Toe-out • Toe-in results is inherently stable • Toe-out is inherently unstable • Race cars often use front toe-out, & rear toe-in

  8. Common Suspension Designs • Beam Axle • Swing Axle • De Dion • Double Wishbone / Unequal Length A-arm

  9. Beam Axle • Around since horse and chariot days • Always keeps wheels parallel • Often used in rear • Rarely used in front • OK on smooth tracks

  10. Swing Axle • Often used on VW based off road cars • Simple and rugged • Camber curve too steep • Only adjustment you can make is ride height

  11. De Dion • Essentially a beam axle with the diff now sprung weight • Keeps wheels parallel • Relatively light weight • Better on smooth tracks

  12. Double Wishbone • Lightest weight • Lowest unsprung mass • Greatest adjustability

  13. Basic Vehicle Dynamics Part 2 • What is Vehicle Dynamics? • The understanding and study of how a vehicle and its components move and react

  14. Yaw, Pitch, and Roll • Same terminology as aircraft • X is the longitudinal axis • Yawing refers to normal change of direction • Pitching is dive or squat

  15. Understeer • Front end of the car “washes out” or doesn’t “turn in” • NASCAR boys call it “push” or “tight” • Safe, because lifting off throttle reduces it • Most road cars have a ton of it

  16. Oversteer • Rear end of car slides out • NASCAR boys call it “loose” • Excessive application of power can cause oversteer • Throttle induced oversteer is never the fast way around a corner

  17. Weight Transfer • Occurs anything the vehicle accelerates or decelerates • Cornering force Fc will cause weight to transfer from the inside to outside tires • Braking and accelerating forces cause a similar front and rear weight transfer

  18. Roll Center • A geometric construct • Represents the instantaneous point about which the sprung mass will rotate due to cornering forces • Roll center moves as suspension travels • Goal of any suspension designer is to minimize Roll Center Migration

  19. Roll Couple • Distance from roll center to CG is key • Low roll center results in more roll for a given lateral acceleration • Most designs use a low roll center to reduce jacking forces

  20. Anti-dive • Purely geometric method to reduce pitch movement • Reduces suspension compliance over bumps • No longer in favor with formula car and sports racers • Might work well for Baja

  21. Bump Steer • Caused when toe changes as suspension moves up and down • Causes car to react unexpectedly over bumps and in roll • Sometimes used intentionally, but be careful

  22. Tire Slip Angle • Angle between the centerline of the wheel and the actual path • Tires generate highest cornering forces at a certain slip angle

  23. Slip Angle vs. Grip • Grip is highest a set angle, then falls off as the slip angle increases • Sharper peak will give a less predictable breakaway • Radial tires typically have a steeper slope than bias ply

  24. Friction Circle • Plots the theoretical limits of adhesion in 2 axes • Great tool for analyzing driver to driver variation • G-analyst is a cheap tool for this

  25. Friction Circle, cont. • Illustrates the trade off between cornering and braking/accelerating • The driver that follows the path closest to the outside of the circle wins

  26. Car Balance • A well balanced car will exhibit both understeer and oversteer at different points on the course and at corner entry and exit • A good driver can change his technique to change the basic oversteer/understeer balance

More Related