1 / 32

Oxy Fuel Cutting Systems Basic Setup & Use

Oxy Fuel Cutting Systems Basic Setup & Use. Typical Torch System. Oxygen Cylinder Acetylene Cylinder Method of Securing the cylinders Caps Regulators Backflash arrestors Hoses Torch Body Torch Head Torch Tip Clothing and Eye/Face Protection. Oxygen Cylinders.

elisa
Download Presentation

Oxy Fuel Cutting Systems Basic Setup & Use

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Oxy Fuel Cutting SystemsBasic Setup & Use

  2. Typical Torch System • Oxygen Cylinder • Acetylene Cylinder • Method of Securing the cylinders • Caps • Regulators • Backflash arrestors • Hoses • Torch Body • Torch Head • Torch Tip • Clothing and Eye/Face Protection

  3. Oxygen Cylinders • Oxygen is very pure - 99% • Pressure is about 2200 psi at 700 F • Forged from a single piece of steel - no welding • Minimum of 1/4” thickness • Stored away from combustibles

  4. T K LK S D,E,Y,U,LE Q ME MBE XAD MD R Oxygen cylinder sizes:

  5. Acetylene Cylinders • Acetone - absorbs acetylene under pressure • Temperature has an extreme affect on pressure • Protected valve or cylinder cap • Stored away from oxygen and combustibles

  6. Oxygen Cylinder Valve • Brass Construction • Double back seat - NEVER LEAVE HALF OPEN • Pop off valve - (fragile disk) • Right hand Thread

  7. Acetylene Cylinder Valve • Brass Construction • Packed valve - OPEN 1/2 TO 3/4 TURN • Hand wheel or tank wrench - NEVER REMOVE WRENCH during use • RH (Male) or LH (Female) Thread

  8. Manifold Systems • Increased Efficiency • more stations • no downtime

  9. Parts: • Cylinders • Hoses - Brass or braided • Check valves or hand valves • Flashback Arrestors - OSHA • Regulators • Main valves

  10. Regulators • Each regulator has two gauges mounted on a single manifold, one indicates cylinder pressure and the other indicates working pressure for the torch

  11. Pressure Regulating Valves • Each regulator has an adjusting screw so pressure to the torch can be quickly controlled by turning the screw righty-tighty increases pressure, left-loosey decreases pressure

  12. Protector Cap • Protects valve from being knocked off • Must be in place when Regulators are off

  13. Backflash Arrestor • Torch / Manifold • Regulator / torch

  14. Hoses • Acetylene= Red • Notch around nut means LH thread • Oxygen = Green • RH Thread • New Hoses have talc inside - Blow out before connecting to torch

  15. Needle valves Preheat / Cutting hole pressures

  16. Torch Body • Torch body is the part of the torch that is held, it contains two needle valves to control flow of gas • single stage / dual stage

  17. Cutting HeadWelding head contains mixer, mixing throat, and the welding tip

  18. Cutting Tips • 1 or 2 piece Rosebud FOR HEATING

  19. Acetylene safety Precautions • Never call acetylene “gas” • Extremely explosive with air or oxygen • Leave wrench on tank

  20. Oxygen Safety Precautions • Never call oxygen “Air” • Never allow oxygen to come in contact with oil, grease, or other petroleum bases • Never use oxygen for compressed air • Never move cylinders without caps • Always secure cylinders

  21. Setup Procedures for Oxy-Acetylene Systems • Do not move cylinders without valve protection • Secure cylinders • Inspect threads • “Crack” Oxygen Valve • Attach regulators and tighten • Blow talc from new hoses • Attach Flashback arrestors, check valves, hoses, check valves, torch body, torch head, and tip • Properly pressurize torch and check for leaks

  22. Procedures for Lighting Oxy-Acetylene Systems • SCREW ADJUSTING SCREW OUT • Stand to the side of the adjusting screw • Open tanks one at a time (Oxygen wide, Acetylene 1/2 turn) • Adjust regulators • Bleed lines one at a time • Fine adjustments made while bleeding the hoses • Open the acetylene needle valve and light torch • Open high pressure oxygen needle valve wide • Adjust to a neutral flame

  23. Shut Down Procedure for Oxy-Acetylene Systems • Turn off acetylene needle valve • Turn off preheat oxygen needle valve • Turn off tanks • Bleed lines one at a time • TURN ADJUSTING SCREWS OUT • Turn off all needle valves

  24. Resume Cutting Heat the starting point Move the oxygen hole off the edge of the plate and start the oxygen stream Starting or restarting a cut

  25. Offhand Cutting Techniques • Rolling your hands • “Pre-load” your wrist and forearm • Roll, don’t slide for a smoother cut • Sliding the torch through your fingers • Apply pressure to torch tubes with thumb and index finger • Keep other three fingers in fist • Don’t move the torch body hand during stops and starts.

  26. Beveling Angles • Slide the torch through your fingers toward you. • Only move the hand nearest the flame when continuing the cut. • Keep your other three fingers in your fist. This will keep your hands cooler and allow you to make a better cut.

  27. Termsand Definitions • Penetration: Distance from the original surface of the base metal to that depth at which fusion stops. • Base Metal: Metal to be welded • Fusion Welding: process that joins metals by heating them to a melting point and allowing them to fuse or flow together.

  28. Backfire: A short pop of the torch flame followed by extinguishing of the flame or continued burning of the gases. • Preheating: Heating prior to a welding or cutting operation • Flashback: when the torch flame moves into or beyond the mixing chamber. • Tack Weld: A short weld used to hold workpieces together

  29. Safety • Watch where you cut • Don’t blow molten metal toward another person • Don’t melt the hoses • Don’t drop metal on hoses • Don’t let hoses lay on hot metal • Release adjusting screw on regulators before opening valves

  30. Stand on the opposite side of the regulator when opening a valve • Open cylinder valve slowly, oxygen first all the way open and acetylene just a quarter of a turn • Do not use or compress acetylene at pressure higher than 15 psi. • Light acetylene first, shut it off first • Never use oil on regulators or any equipment

  31. Do not use oxygen as a substitute for compressed air • Keep heat, flames and sparks away from combustibles. • Keep hoses out of sparks or spatter to prevent leaks • Never use Leather Gloves to pick up metal; use pliers • Wear welding goggles or a face shield with a lens no. 4-6. • Never wear synthetic clothing; wear cotton.

  32. BACK TO OXYFUEL EQUIPMENT

More Related