1 / 13

MAGM 225

Motor Control. Electric motors present some special problems from the standpoint of control. An electric motor will try to provide the power required by a load, even if it results in self-destruction. Therefore a motor must be protected from overloads. A motor draws up to six times as much current when the rotor is not turning as it does when operating at full speed. If a motor should stall the control device and the disconnect switch must be capable of handling the high locked-rotor curr30726

erma
Download Presentation

MAGM 225

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


    2. Motor Control Electric motors present some special problems from the standpoint of control. An electric motor will try to provide the power required by a load, even if it results in self-destruction. Therefore a motor must be protected from overloads. A motor draws up to six times as much current when the rotor is not turning as it does when operating at full speed. If a motor should stall the control device and the disconnect switch must be capable of handling the high locked-rotor current.

    3. Types of Motor Controllers A controller is simply a means of closing the circuit supplying power to an electrical motor. The most simple control device is a cord and plug. (1/8hp or less) A branch-circuit protective device, ie breaker, may serve as the controller for stationary motors of 1/8 HP or less that normally operate continuously A time delay circuit breaker is also allowed as a control device. A fusible knife switch may act as a motor controller provided it is rated for the horsepower rating of the motor supplied.

    4. Magnetic Motor Starter The main contacts are located inside the unit Repair kits are available When current is supplied to the internal solenoid the motor-starter contacts are closed. An overload relay section is added to the motor starter to sense motor current.

    5. NEMA Sizes NEMA has developed a standard numbering system for motor starter sizes. All manufactures use this system The larger the rating number the greater the horsepower rating of the starter. Are rated according to the current they will be expected to carry continuously, and interrupt the if the motor should stall. Motor starters come in 2 or 3 poles. 2 pole is for single phase and 3 pole for 3 phase. A 3 pole motor starter will handle a single phase motor with a horsepower rating half as large as 3 phase motor.

    6. Enclosures The motor-starter housing is selected for the environment in the area. NEMA has developed a standard numbering system for enclosures and require they be marked by the manufacture. NEMA 1 - dry and free from dust and flammable materials NEMA 3 – weather resistant suitable for outdoors but not dusty conditions. NEMA 4 – water and dust tight. NEMA 4x – water and dust tight but also corrosion resistant. NEMA 7 – Explosion proof. NEMA 9 – Dust Ignition proof

    7. Motor-Full load current The motor full-load current is used to determine the minimum size of circuit components. The name plate current rating must be used for selecting the maximum size motor running overload protection. Wires supplying a single motor shall have an amperage rating of not less that 1.25 times the full-load current of the motor.

    8. Short-Circuit Protection Motor circuits must be protected from excessive current, ground faults, and short circuits. Over current protection can be fused or circuit breaker a circuit beginning. Short circuit and ground fault must be capable of carrying the starting current of the motor. A single-phase, 5-hp, 230v motor with a nameplate of 28amps drives a normal load. Determine the overload device. Full load current = 28A Fuse multiplier = 125% 1.25x28A=35A Use a 50-A fuse.

    9. Service supplying several motors The feeder wires are required to have a minimum rating equal to the sum of the full-load current of all motors supplied, plus 25%. Motors of 5-hp 28a , 3-hp 17a, 1-hp 8a, and 2-hp 12amp.=72amps. No. 4 AWG minimum (from wire charts) The disconnect must be selected for a horsepower rating of not less than the sum of all HP ratings. 5+3+1+2=11hp The disconnect closest is likely 15 hp If a breaker is used it must be a minimum of 115% of the sum of the full-load current for all motors served. (28+17+8+12)1.15=75Amps

    10. Feeder Taps A common practice is to tap motor branch circuits from a motor feeder. This is permitted as long as the branch-circuit wire is terminated at an over current of proper size.

    11. Motor Control Circuit A magnetic motor starter is operated with an electric solenoid coil. Here we have a typical wiring diagram for a magnetic motor control. The thick lines are the power flow to the motor, the thin lines belong to the control circuit and generally are pre-wired by the manufacture.

    12. Control Devices Common wiring schematics use basic symbols and terminology. Switches and contacts are the basic control components, and they take several different forms. They can be operated mechanically, by timer, change in condition like temperature, pressure, flow, liquid level, or humidity. Switches and contacts are described by the number of pole and number of throws. Poles – the number of paths into a switch or contact. Throws – the number of paths leaving each pole. It must also be known if the switch is normally open or normally closed when inactivated.

    13. Control Devices The common types of switches and contacts are incorporated into various types of control devices.

    14. Reversing Motor Starters Electric motors may be called upon to drive a machine which must be reversible. A reversible motor starter is required to select the desired rotation direction. 3-phase – only two of the three leads need to be reversed. Single phase the start windings must be reversed with respect to the run windings. Drum switch has forward, reverse, and stop. Note the phase rotation at the motor for forward and reverse.

More Related