1 / 55

Mitsubishi RA90 4 axis Wire EDM

Mitsubishi RA90 4 axis Wire EDM. Machine Tool Technology Lake Area Technical Institute Some pictures copied from Mitsubishi. Outline. RA90 Overview - Slide 3 Control Buttons and Lights Jogging the machine Rethreading the wire - Slide 37 Mounting Workpieces Pickups Nozzles

esmerelda
Download Presentation

Mitsubishi RA90 4 axis Wire EDM

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. MitsubishiRA90 4 axis Wire EDM Machine Tool Technology Lake Area Technical Institute Some pictures copied from Mitsubishi

  2. Outline • RA90 Overview -Slide 3 • Control Buttons and Lights • Jogging the machine • Rethreading the wire -Slide 37 • Mounting Workpieces • Pickups • Nozzles • Flow of Machining Operations • Power Settings Mitsubishi-Epacks

  3. Control Panel

  4. The 4 different axes • X is the left to right • Y is front to back • U is to X and moves on top left to right • V is to Y and moves on top front to back • What we program will be 2 axis programs. -We will use the taper function, which utilizes all 4 axes, but 4-axis programming is VERY difficult.

  5. Control Buttons and Lights Pg 1

  6. Start up • Press the Screen on/off button • To turn the screen back on • Release the emergency stop button • The computer is ready to be used now • To jog the machine you must press the Ready button. • Press the “Ready” button • The Deionization system will start • You will be able to jog the machine or start a cut.

  7. 2nd 1st 3rd

  8. Shutdown • Press the Emergency Stop button • Clean the water and debris off • Turn off the light • Close the front cover • Turn off the screen with the screen on/off button Screen Off

  9. Start up from Complete Shutdown • Press POWER ON (green button located on top of the screen) • NOTE: do not need to do the following • ZERO POINT RETURN • located on the work piece setup page • Press READY button located on top right hand side of the control panel • Move to LEFT REAR corner using the hand held pendant (can adjust the speed by pressing one of the 4 speed keys) • Work piece setup • ZERO POINT RETURN • Select all axis (when finished at the top right of the screen it will display MOVE FN = move finished)

  10. Workpiece Setup Screen

  11. Jogging the machine • On the Handheld pendant • Press the Hand button • The speed of movement is selected at the top of the pendant. • Rapid, Medium, 0.0005, 0.0001 • Press and hold one of the 4 bottom buttons • -X, +Y, -Y, +X

  12. Hand Held Pendant

  13. 0.0005 Medium Rapid 0.0001 Edge Find Wire Align Center Find Manual Wire Contact Do Not Use Yet Jogs the U or V axes

  14. Jog Speeds

  15. Mounting Workpieces • The Bed of the RA90 is Soft Stainless steel • Don’t drop parts, etc. on it! • Threads do Not go through • So the screws do not hit the bottom flush cup • Use paper towels to clean it • Not shop rags • Incase there are metal chips in the rags • Lay workpiece on edge and tilt down • Place a penny under the heel block

  16. Misc. Notes • Keep clamps etc. low profile • So they do Not hit the upper guide etc. • You do not have to clamp them as good as on a milling machine. • The EDM does not apply any pressure to the workpiece. • Use stainless steel capscrews and fixturing when possible

  17. Rethreading • Gentlypull the wire through the top wire guide. Above the top wire guide, there is a wheel with a handle on it, USE IT to bring out more wire approximately 2.5 feet. • Then there are 2 ways of turning on the WIRE COLLECT. • Flip the toggle switch up, located at the lower part of the control panel. • And it will start. You should hear the vacuum sound start. • Press the S10 key NEXT and the wire collect will appear the S7 key. • The “S” keys are located at the bottom of the screen.

  18. Pickups • Work-piece pickups

  19. Pickup Center of Hole • Select the Center button on the pendant • Press one of the directional axis jog buttons • This determines where to start the touch-off

  20. Corner Pick-up • Select the Corner-p button on the pendant Set the following • Start Dist X ______ • Y ______ • Machine St. Pt. X ______ • Y ______ Measure times _1_ Stp. IN

  21. Edge Pickup Used to find one edge’s location.

  22. Water level Gauge Water Level Low Correct Water Level Water Overfull

  23. Nozzle Positioning • Upper water nozzle should be 0.010 away from the top of the workpiece.

  24. Flow of Operations to Run a program

  25. Power Settings Mitsubishi-Epacks The “IP” is the parameter we change. -We reduce the “IP” if Wire keeps breaking

More Related