1 / 37

ECE 353 Introduction to Microprocessor Systems

ECE 353 Introduction to Microprocessor Systems. Michael Schulte. Week 7. Administrative Matters. Homework #4 is due Friday, April 4 th , 2008 Quiz #2 is rescheduled for Thursday, April 10 th from 7:15 to 8:30 Discussion section tonight 6:30-8:00pm in 3534 Engineering Hall

krystal
Download Presentation

ECE 353 Introduction to Microprocessor Systems

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. ECE 353Introduction to Microprocessor Systems Michael Schulte Week 7

  2. Administrative Matters • Homework #4 is due Friday, April 4th, 2008 • Quiz #2 is rescheduled for Thursday, April 10th from 7:15 to 8:30 • Discussion section tonight 6:30-8:00pm in 3534 Engineering Hall • Memory Maps and Address Decoding • Reading for week8 • ADuC702X Datasheet 53-60, 71-73, 75-79

  3. Topics • Microprocessor support circuits • Clock and reset generation • Power control • Microprocessor supervisors • I/O subsystems • GPIO pin construction • I/O port design • I/O decoding • I/O synchronization • ADuC7026 GPIO

  4. ADuC7026 Block Diagram

  5. Clocks • Clock Generation • Clock oscillators • External clocks • Phase-locked loops (PLLs) • Operation and design issues • ADuC7026 clocking • PLLCON • Power Control • ADuC7026 operating modes • POWCON ADuC7026 pin-out

  6. Reset • The reset signal is used to force the processor into a known state from which operation can reliably be started. • On power up, the reset signal should be asserted long enough to ensure that the supply voltages are stable and the oscillator is running and stable • Reset Generation • RC reset circuit operation • Shortcomings ADuC7026 pin-out

  7. Microprocessor Supervisors • Microprocessor supervisors provide reset functionality for a variety of circumstances • Power-up • Brown-out • Glitches • They can also provide a number of other services • MAX807 ADuC7026 pin-out

  8. Basic System Bus Operation • Address • Unidirectional from CPU • Data • Bidirectional • Control • /RS or /RD – output from CPU • Indicates a read operation in progress • /WS or /WR – output from CPU • Indicates a write operation in progress • /WAIT or /READY – input to CPU • Used by external device to signal that it is not able to complete transfer yet • Read/Write Sequence

  9. I/O Port Basics • I/O subsystems allow the CPU to interact with the outside world • Basic GPIO pin requirements • Configurable as input or output • Can set value driven out on the pin • Can read the current value on the pin • Configurable vs. multiplexed pins • Unconditional I/O • The I/O device can accept or return data without delay ADuC7026 pin-out

  10. MSI I/O Ports • Medium Scale Integration (MSI) circuits are available to construct ports • Simple byte input ports can be constructed from… • Octal buffers • Octal registers • Simple byte output ports can be constructed from octal registers

  11. P Compatible I/O Devices • Complex I/O devices typically require more sophisticated interface and control logic • P compatible I/O devices have the necessary logic built in to the device itself • Interface designed to be reasonably compatible with many microprocessor buses • Need to add decoding/selection logic • Example • Device controllers • An organizational model commonly used to interface to complex I/O devices (serial ports, LCDs, disk drives, etc.) • Generic model • Example – Hitachi HD44780U LCD Controller

  12. I/O Address Decoding • I/O address decoding determines the logical location of the I/O device • Isolated I/O • Memory-mapped I/O • Input vs. output ports • Same address does not guarantee same function! • Exhaustive address decoding • Partial address decoding

  13. I/O Address Decoding (cont.) • Linear selection decoding • A single address line is used as the selection criteria for each device • Can have n input/output devices in a system with an n-bit address bus • Hazards and opportunities • Note that this idea has a very limited application space!

  14. Conditional I/O • Conditional vs. unconditional transfers • I/O synchronization • Hardware example • Polling • Overhead • Flags / semaphores • Wait loops • Timeouts • Software exercise

  15. ADuC7026 GPIO Ports • The ADuC7026 has 40 pins organized as 5 ports that can be used as digital GPIO • All pins have multiple functions in addition being able to be used as GPIO • The configuration selection is set through the GPxCON MMR.

  16. ADuC7026 GPIO MMRs • GPxCON • Determine which of a pin’s functions are active • This is the configuration column selection on the previous slide aduc7026.inc

  17. ADuC7026 GPIO MMRs (cont) • GPxPAR • PARameters • Controls whether or not the internal pull-ups are used. • Does not apply to ports 2 and 4

  18. ADuC7026 GPIO MMRs (cont) • GPxDAT • Control the pin direction • Set the output state • Read the pin value • Read the pin values that were present at reset

  19. ADuC7026 GPIO MMRs (cont) • GPxSET • Write 1s to set the output value • 0s have no effect

  20. ADuC7026 GPIO MMRs (cont) • GPxCLR • Write 1s to clear the output value • 0s have no effect

  21. General Purpose I/O Exercise • Write a program that • Configures port P1 as a GP input port and P2 as a GP output port. • Sets P2 to 0xF7 • Reads the value on P1 at reset • Copies the value on P1 to P2 • Changes the least significant nibble of P2 to C, without changing the more significant nibble

  22. Wrapping Up • Reading for week8 • ADUC 53-60, 71-73, 75-79

  23. ADuC7026 Clock Generation

  24. ADuC7026 PLLCON

  25. ADuC7026 Operating Modes

  26. ADuC7026 POWCON

  27. ADuC7026 Functional Block Diagram

  28. MAX807

  29. 74HC540/541

  30. 74HC573

  31. 74HC574

  32. AD7865

  33. Generic Device Controller

  34. HitachiHD44780ULCDController

  35. Conditional I/O Exercise Write a subroutine to read data from an input device like the hardware example. Assume that the flag is a READY signal (active high). If the device does not become ready after 1 trillion polling attempts, return with R0 = -1, otherwise, return with the data in R0.

  36. Conditional I/O Example /MS0 base address = 0x1000 0000

  37. aduc7026.inc ;GPIO GPIO_MMR_BASE EQU 0xFFFFF400 GP0CON EQU 0x00 GP1CON EQU 0x04 GP2CON EQU 0x08 GP3CON EQU 0x0C GP4CON EQU 0x10 GP0DAT EQU 0x20 GP0SET EQU 0x24 GP0CLR EQU 0x28 GP0PAR EQU 0x2C

More Related