1 / 20

VLSI Testing Lecture 1: Introduction

VLSI Testing Lecture 1: Introduction. Dr. Vishwani D. Agrawal James J. Danaher Professor of Electrical and Computer Engineering Auburn University, Alabama 36849, USA vagrawal@eng.auburn.edu http://www.eng.auburn.edu/~vagrawal IIT Delhi, Aug 17, 2013, 10:00-11:00AM. Course Description.

masako
Download Presentation

VLSI Testing Lecture 1: Introduction

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. VLSI TestingLecture 1: Introduction Dr. Vishwani D. Agrawal James J. Danaher Professor of Electrical and Computer Engineering Auburn University, Alabama 36849, USA vagrawal@eng.auburn.edu http://www.eng.auburn.edu/~vagrawal IIT Delhi, Aug 17, 2013, 10:00-11:00AM Lecture 1 Introduction

  2. Course Description This course is designed for the MTech program in VLSI at IIT, Delhi. It is patterned after a one-semester graduate-level course offered at Auburn University. A set of 17 lectures that include classroom exercises provide understanding of theoretical and practical aspects of VLSI testing. The course fulfills the needs of today’s industrial design environment, which demands knowledge of testing concepts of digital, memory, analog and radio frequency (RF) subsystems often implemented on a system-on-chip (SoC). Lecture 1 Introduction

  3. Outline • Lecture 1: Introduction (18*+2) * Number of slides • Lecture 2: Yield and quality (16+3) • Lecture 3: Fault modeling (20+2) • Lecture 4: Testability analysis (27) • Lecture 5: Logic simulation (15) • Lecture 6: Fault simulation (19) • Lecture 7: Combinational ATPG (24+3) • Lecture 8: Sequential ATPG (19+2) • Lecture 9: Delay test (26) • Lecture 10: Memory test (26) • Lecture 11: Analog test (27) • Lecture 12: Model-Based and Alternate Test (15) • Lecture 13: DFT and Scan (23+2) • Lecture 14: BIST (29) • Lecture 15: System diagnosis (21) • Lecture 16: RF Testing: Introduction, Gain Measurement (39) • Lecture 17: RF Testing: Intermodulation and Noise Measurements (34) Lecture 1 Introduction

  4. Schedule • Aug 17, 2013 – 10AM-12PM Lectures 1 and 2 • Aug 19, 2013 – 2:30-4:30PM Lectures 3 and 4 • Aug 20, 2013 – 2:30-4:30PM Lectures 5 and 6 • Aug 21, 2013 – 2:30-4:30PM Lectures 7 and 8 • Aug 23, 2013 – 2:30-4:30AM Lectures 9 and 10 • Aug 24, 2013 – 10AM-12PM Lectures 11 and 12 • Aug 24, 2013 – Take-Home Exam assigned • Aug 26, 2013 – 2:30-4:30PM Lectures 13 and 14 • Aug 27, 2013 – 2:30-4:30PM Lectures 15 and 16 • Aug 28, 2013 – 2:30-4:30PM Lectures 17 • Aug 28, 2013 –Take-Home Exam due 4:30PM Lecture 1 Introduction

  5. Introduction • VLSI realization process • Verification and test • Ideal and real tests • Costs of testing • Roles of testing • A modern VLSI device - system-on-a-chip • Testing • Digital • Memory • Analog • RF • Textbook • Problem to solve Lecture 1 Introduction

  6. VLSI Realization Process Customer’s need Determine requirements Write specifications Design synthesis and Verification Test development Fabrication Manufacturing test Chips to customer Lecture 1 Introduction

  7. Definitions • Design synthesis: Given an I/O function, develop a procedure to manufacture a device using known materials and processes. • Verification: Predictive analysis to ensure that the synthesized design, when manufactured, will perform the given I/O function. • Test: A manufacturing step that ensures that the physical device, manufactured from the synthesized design, has no manufacturing defect. Lecture 1 Introduction

  8. Verification Verifies correctness of design. Performed by simulation, hardware emulation, or formal methods. Performed once prior to manufacturing. Responsible for quality of design. Test Verifies correctness of manufactured hardware. Two-part process: 1. Test generation: software process executed once during design 2. Test application: electrical tests applied to hardware Test application performed on every manufactured device. Responsible for quality of devices. Verification vs. Test Lecture 1 Introduction

  9. Problems of Ideal Tests • Ideal tests detect all defects produced in the manufacturing process. • Ideal tests pass all functionally good devices. • Very large numbers and varieties of possible defects need to be tested. • Difficult to generate tests for some real defects. Defect-oriented testing is an open problem. Lecture 1 Introduction

  10. Real Tests • Based on analyzable fault models, which may not map on real defects. • Incomplete coverage of modeled faults due to high complexity. • Some good chips are rejected. The fraction (or percentage) of such chips is called the yield loss. • Some bad chips pass tests. The fraction (or percentage) of bad chips among all passing chips is called the defect level. Lecture 1 Introduction

  11. Testing as Filter Process Mostly good chips Good chips Prob(pass test) = high Prob(good) = y Tested chips Fabricated chips Prob(pass test) = low Prob(fail test) = low Mostly bad chips Defective chips Prob(bad) = 1- y Prob(fail test) = high Lecture 1 Introduction

  12. Costs of Testing • Design for testability (DFT) • Chip area overhead and yield reduction • Performance overhead • Software processes of test • Test generation and fault simulation • Test programming and debugging • Manufacturing test • Automatic test equipment (ATE) capital cost • Test center operational cost Lecture 1 Introduction

  13. Present and Future* * SIA Roadmap from www.siaonline.org, July 23, 2012 Lecture 1 Introduction

  14. Design for Testability (DFT) DFT refers to hardware design styles or added hardware that reduces test generation complexity. Motivation: Test generation complexity increases exponentially with the size of the circuit. Example: Test hardware applies tests to blocks A and B and to internal bus; avoids test generation for combined A and B blocks. Int. bus Primary outputs (PO) Primary inputs (PI) Logic block A Logic block B Test input Test output Lecture 1 Introduction

  15. Cost of Manufacturing Test in 2000AD • 0.5-1.0GHz digital clock; analog instruments; 1,024 digital pins: ATE purchase price • = $1.2M + 1,024 x $3,000 = $4.272M • Annual running cost (five-year linear depreciation) • = Depreciation (20%) + Maintenance (2%) + Operation ($0.5M) • = $0.854M + $0.085M + $0.5M • = $1.439M/year • Test cost (24 hour ATE operation) • = $1.439M/(365 x 24 x 3,600) • = 4.5 cents/second Lecture 1 Introduction

  16. Roles of Testing • Detection: Determination whether or not the device under test (DUT) has some fault. • Diagnosis: Identification of a specific fault that is present on DUT. • Device characterization: Determination and correction of errors in design and/or test procedure. • Failure mode analysis (FMA): Determination of manufacturing process errors that may have caused defects on the DUT. Lecture 1 Introduction

  17. A Modern VLSI DeviceSystem-on-Chip (SOC) DSP core RAM ROM Transmission medium Data terminal Mixed- signal Codec Inter- face logic Lecture 1 Introduction

  18. Textbooks • Digital, memory and mixed-signal: • M. L. Bushnell and V. D. Agrawal, Essentials of Electronic Testing for Digital, Memory and Mixed-Signal VLSI Circuits, Springer, 2000. • http://www.eng.auburn.edu/~vagrawal/BOOK/books.html • RF testing • J. Kelly and M. Engelhardt, Advanced Production Testing of RF, SoC, and SiP Devices, Boston: Artech House, 2007. • B. Razavi, RF Microelectronics, Upper Saddle River, New Jersey: Prentice Hall PTR, 1998. • K. B. Schaub and J. Kelly, Production Testing of RF and System-on-a-chip Devices for Wireless Communications, Boston: Artech House, 2004. Lecture 1 Introduction

  19. A Problem to Solve • Using the testing cost obtained in Slide 15, determine what is the component of test in the cost of a mixed-signal VLSI chip for the following data: • Analog test time = 1.5 s • Digital test clock = 200MHz • Number of digital test vectors = 109 • Chip yield = 70% Lecture 1 Introduction

  20. Solution Assuming that one vector is applied per clock cycle during a digital test, the rate of test application is 200 million vectors per second. Therefore, Digital test time = (1000 × 106)/(200× 106) = 5 seconds Adding the analog test time, we get, Total test time = 1.5 + 5.0 = 6.5 seconds The testing cost for a 500 MHz, 1,024 pin tester was obtained as 4.56 cents in Slide 15. Thus, Cost of testing a chip = 6.5 × 4.56 = 29.64 cents The cost of testing bad chips should also be recovered from the price of good chips. Since the yield of good chips is 70%, we obtain Test cost per good chip = 29.64/0.7 ≈ 42 cents 42 cents should be included as the cost of testing while figuring out the price of chips. Lecture 1 Introduction

More Related