1 / 36

CHAPTER 6: MECHANICAL PROPERTIES

CHAPTER 6: MECHANICAL PROPERTIES. ISSUES TO ADDRESS. • Stress and strain : What are they and why are they used instead of load and deformation?. • Elastic behavior: When loads are small, how much deformation occurs? What materials deform least?.

Download Presentation

CHAPTER 6: MECHANICAL PROPERTIES

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. CHAPTER 6: MECHANICAL PROPERTIES ISSUES TO ADDRESS... • Stress and strain: What are they and why are they used instead of load and deformation? • Elastic behavior: When loads are small, how much deformation occurs? What materials deform least? • Plastic behavior: At what point do dislocations cause permanent deformation? What materials are most resistant to permanent deformation? • Toughness and ductility: What are they and how do we measure them? 1

  2. Chapter 6: Mechanical Properties of Metals6.1 Introduction • Why Study the Mechanical Properties of Metals ? • It is important for engineers to understand • How the various mechanical properties are measured, and • What these properties represent • The role of structural engineers is to determine stresses and stress distributions within members that are subjected to well-defined loads • By experimental testing • Theoretical and mathematical stress analysis. • Design structures/components using predetermined materials such that unacceptable levels of deformation and/or failure will not occur.

  3. 6.2 Concepts of Stress and Strain • Static load changes relatively slowly with time • Applied uniformly over a cross-section or surface of a member. • Tension • Compression • Shear • Torsion

  4. 6.2 Concepts of Stress and Strain (Contd.) • TENSION TEST • Most common mechanical stress-strain test • Used to ascertain several mechanical properties that are important in design • A specimen is deformed, usually to fracture, with a gradually increasing tensile load that is applied uniaxially along the long axis of the specimen. • A standard specimen is shown in Figure 6-2.

  5. 6.2 Concepts of Stress and Strain (Contd.) • The specimen is mounted by its ends into the holding grips of the testing apparatus (Figure 6-3). • Tensile testing machine • To elongate the specimen at a constant rate • To continuously and simultaneously measure the instantaneous load and the resulting extension • Load using load cell • Extension using extensometer • Takes few minutes and is destructive.

  6. 6.2 Concepts of Stress and Strain (Contd.) • Engineering Stress (s) = Instantaneous applied load (F) / Original Area (Ao) • Unit: MPa, GPa, psi • Engineering strain (e) • li = instantaneous length • lo = original length • COMPRESSION TESTS • Similar to tensile test, compressive load • Sign convention, compressive force is taken negative  stress negative • Since lo > li , negative strain

  7. 6.2 Concepts of Stress and Strain (Contd.) • SHEAR AND TORSIONAL TESTS • Shear stress : t = F / Ao • F: Load or force imposed parallel to the upper and lower faces • Ao: shear or parallel area • Shear strain (g) is defined as the tangent of the strain angle q.

  8. 6.2 Concepts of Stress and Strain (Contd.) • GEOMETRIC CONSIDERATIONS OF THE STRESS STATE • Stress is a function of orientations of the planes

  9. ELASTIC DEFORMATION 1. Initial 2. Small load 3. Unload Elastic means reversible! 2

  10. ELASTIC DEFORMATION6.3 Stress-Strain Behavior • Elastic deformation: • Non-permanent, completely reversible, conservative • Follow same loading and unloading path • Linear elastic deformation • Hooke’s Law • Modulus of elasticity or Young’s Modulus  stiffness or a material’s resistance to elastic deformation

  11. 6.3 Stress-Strain Behavior (Contd.)

  12. Nonlinear Elastic Behavior • Gray cast iron, concrete, many polymers • Not possible to determine a modulus of elasticity • Eithertangent or secant modulus is normally used.

  13. 6.3 Stress-Strain Behavior (Contd.) • On an atomic scale, macroscopic elastic strain is manifested as small changes in the interatomic spacing and the stretching of interatomic bonds.  E is a measure of the resistance to separation of adjacent atoms • Modulus is proportional to the slope of the interatomic force-separation curve (Fig 2.8a) at equilibrium spacing

  14. 6.3 Stress-Strain Behavior (Contd.) • With increasing temperature, the modulus of elasticity diminishes • Shear stress and strain are proportional to each other: • Shear modulus or modulus of rigidity ( Table 6.1)

  15. 6.4 Anelasticity • Up to this point, it is assumed that • Elastic deformation is time-independent • An applied stress produces an instantaneous elastic strain • Strain remains constant over the period of time the stress is maintained • Upon release of the load, strain is totally recovered (immediately returns to zero) • In most engineering materials, there will also exist a time-dependent elastic strain component , i.e. • elastic deformation will continue after stress application • Upon load release some finite time is required for complete recovery • Loading and unloading path are different • Anelasticity : time-dependent elastic behavior • For metals, the anelastic component is normally small and neglected. • For some polymers, it is significant and known as viscoelastic behavior (Sec. 16.7)

  16. 6.5 Elastic Properties of Materials • Poisson’s ratio • E = 2G(1 + n) • Example 6.1 • Example 6.2

  17. PLASTIC DEFORMATION • For most metals, elastic deformation persists only to strains of about 0.005 • Plastic deformation • Stress not proportional to strain (Hooke’s law cease to be valid) • Permanent • Nonrecoverable • Non-conservative • Transition from elastic to plastic deformation • Gradual for most metals • Some curvature results at the onset of plastic deformation

  18. PLASTIC DEFORMATION (METALS) 1. Initial 2. Small load 3. Unload Plastic means permanent! 3

  19. PLASTIC (PERMANENT) DEFORMATION (at lower temperatures, T < Tmelt/3) • Simple tension test: 14

  20. Plastic deformation (Contd.) • From as atomic perspective • Plastic deformation corresponds to the breaking of bonds with original atom neighbors • Reforming bonds with new neighbors • Large number of atoms and molecules move relative to one another • Upon removal of stress, they do not return to their original position • Mechanism of plastic deformation: • Crystalline Solids: • accomplished by a process called slip • Involves the motion of dislocations (Sec 7.2) • Non-crystalline solids (as well liquids) • Occurs by a viscous flow mechanism (Sec 13.9)

  21. YIELD STRENGTH, sy • Stress at which noticeableplastic deformation has occurred. when ep = 0.002 15

  22. 6.6 Tensile Properties • YIELDING and YIELD STRESS Typical stress strain behavior (Figure) • Proportional Limit (P) • Yielding • Yield strength In most cases, the position of yield point may not be determined precisely. • Established convention: a straight line is constructed parallel to the elastic portion at some specified strain offset, usually 0.002 (0.2%) Fig. 6.10a  corresponding intersection point gives yield strength.

  23. 6.6 Tensile Properties (Contd.) • Some steels and other materials exhibit the behavior as shown in Fig 6.10b • The yield strength is taken as the average stress that is associate with the lower yield point. • Magnitude of yield strength is a measure of its resistance to plastic deformation • Range from 35 MPa to 1400 MPa • 35 MPa for low-strength aluminum • 1400 MPa for high-strength steel

  24. 6.6 Tensile Properties (Contd.) • TENSILE STRENGTH • Tensile strength TS (MPa or psi) is the stress at the maximum on the engineering stress-strain curve • All deformation up to this point is uniform. • Onset of necking at this stress at some point  all subsequent deformation at this neck. • Range: 50 - 3000 MPa 50 MPa for aluminum 3000 MPa for high strength steel

  25. DUCTILITY, %EL • Plastic tensile strain at failure: Adapted from Fig. 6.13, Callister 6e. • Another ductility measure: • Note: %AR and %EL are often comparable. --Reason: crystal slip does not change material volume. --%AR > %EL possible if internal voids form in neck. 19

  26. Effect of Temperature • As with modulus of elasticity (E), the magnitudes of both yield and tensile strengths decline with increasing temperature • Ductility usually increases with temperature • Figure shown stress-strain behavior of iron

  27. RESILIENCE • Resilience is the capacity of a material to absorb energy when it is deformed elastically and then, upon unloading, to have this energy recovered. • Modulus of resilience (Ur) • Associated property • Area under the engineering stress-strain curve • Strain energy per unit volume required to stress from an unloaded state to yielding • Mathematically,

  28. TOUGHNESS • Energy to break a unit volume of material • Approximate by the area under the stress-strain curve. 20

  29. TOUGHNESS • A measure of the ability of a material to absorb energy up to fracture. • Specimen geometry and the manner of load application are important in toughness determination: • Notch toughness: dynamic (high strain rate) loading, specimen with notch (or point of stress concentration) (Sec 8.6) • Fracture toughness: property indicative of a materials resistance to fracture when crack is present (Sec 8.5) • For static (low strain rate) condition, modulus of toughness is equal to the total area under the stress-strain curve (up to fracture ): For Ductile Material : For Brittle Material:

  30. 6.7 True Stress and Strain • Engineering stress-strain curve beyond maximum point (M) seems to indicate that the material is becoming weaker. • Not true, rather it becomes stronger. • Since cross-sectional area is decreasing at the neck  reduces load bearing capacity of the material • True stress: Actual or current or instantaneous force divided by the instantaneous cross-sectional area. • True Strain: Change in length per unit instantaneous length

  31. 6.7 True Stress and Strain (Contd.) • Relation between two definitions • Above equations are valid only to the onset of necking; beyond this point true stress and strain should be computed from actual load, area and gauge length. Schematic comparison in Figure 6.16 • Corrected takes into account complex stress state with in neck region.

  32. 6.7 True Stress and Strain (Contd.) • For some metals and alloys, the true stress-strain curve is approximated as • Parameter n • strain-hardening exponent • A value less than unity • Slope on log-log plot • Parameter K • Known as strength coefficient • True stress at unit true strain

  33. 6.8 Elastic Recovery During Plastic Deformation • Upon release of load, some fraction of total strain is recovered as elastic strain • During unloading, straight path parallel to elastic loading • Reloading • Yielding at new yield strength

  34. Solve Examples in Class • 6.3 • 6.4 • 6.5 • 6.6 • Design Example 6.1

More Related