'Dial indicator' presentation slideshows

PART PRODUCTION COMMUNICATION MODEL

MANAGEMENT. DESIGN. SALES. PRICING. VENDORS. TOOLING. PLANNING. PURCHASING. PRODUCTION. CUSTOMERS. ROUTING. SERVICE. INSPECTION. ASSEMBLY. PART PRODUCTION COMMUNICATION MODEL. Geometric Dimensioning and Tolerancing (GD&T). Three Categories of Dimensioning.

1.13k views • 76 slides

CHAPTER 23

CHAPTER 23. The Clutch System. Checking and Adjusting a Mechanical Clutch. 23-1.

595 views • 46 slides

Vernier, Dial, and Electronic Digital Calipers

Vernier, Dial, and Electronic Digital Calipers. Session 3. Parts of the Vernier Caliper. Used to lock readings into place. Bar of 25-division vernier scale graduated same as micrometer. Manufactured with both 25- and 50-division vernier scales. Measuring a Workpiece.

2.01k views • 40 slides

Inspect Torque Converter

Inspect Torque Converter . Cutaway View. Turbine Impeller. Clutch Plate. Damper. The internal parts of a TC, torque converter include the: Impeller Turbine Clutch Plate with damper Stator and one-way clutch. Stator. One-way Clutch. Exploded View.

1.36k views • 24 slides

Comparison Measurement

Comparison Measurement. Session 14. Comparison Measurement. Process consisting of comparing measurement of part to known standard or master of exact dimension required Comparators Any instrument used to compare size of workpiece to known standard

464 views • 23 slides

Production Technology (IND 006)

Lecture No. 9. Production Technology (IND 006). Preparatory Year, Faculty of Engineering, Fayoum University. Dr. Ahmed Salah Abou Taleb Lecturer, Industrial Engineering Dept., Faculty of Engineering, Fayoum University. Introduction. Measurement. Measurement.

232 views • 22 slides

Jeff Guzzetti

Jeff Guzzetti. Lubrication and End Play Inspection. Lubrication: The Procedure. Gain access to the tail Remove access panels. FAIRING. ACCESS PANELS. GREASE GUN. Lubrication: The Procedure. Apply grease to acme nut fitting with grease gun until grease exits out top of acme nut.

371 views • 20 slides

Lesson

Lesson. Measuring Engine Components and Specifications. Interest Approach. How are internal combustion engine specifications determined?. Student Learning Objectives. Identify measuring and testing equipment for internal combustion engines

210 views • 20 slides

Manual Transmission Repair

Manual Transmission Repair. General Disassembly Procedures. Refer to the appropriate service manuals for detailed disassembly procedures Check end play and clearances before disassembly Check detent springs and balls as they are removed They MUST be replaced correctly

559 views • 16 slides

How to Tram a Mill Head

How to Tram a Mill Head. Why is tramming a mill head important?. Ensures Tool is ____________ to table surface in both the x and y directions. Ensures that milled surfaces are mutually _____________________.

252 views • 12 slides

Beam Bending Lab Introduction

ENGR 1181. Beam Bending Lab Introduction. Engineering Education innovation Center. Beam Bending Lab Concepts. 1. Stress, Strain, Young's modulus 2. Moment of Inertia 3. Force and deflection of a cantilever beam 4. Dial caliper and d ial indicator measurements. ENGR 1181.

254 views • 7 slides

Overview

Overview. Radial Pads. Shaft. Upper hub (rotating). Lower hub (rotating). Thrust Pad. Upper and Lower hub (installed). Upper hub. Lower Hub. Radial Pad.

44 views • 4 slides

Rotary Table

Mount for mill table. Clamps. Uses/ Purpose: Cutting Circular Grooves Circular hole patterns Angled Cuts. Rotary Table. Setup: 1. Mount the rotary table to the mill table 2. Find the center of the rotary table using Dial Indicator and set X and Y to zero on read out.

259 views • 2 slides

Rotary Table

Mount for mill table. Clamps. Uses/ Purpose: Cutting Circular Grooves Circular hole patterns Angled Cuts. Rotary Table. Setup: 1. Mount the rotary table to the mill table 2. Find the center of the rotary table using Dial Indicator and set X and Y to zero on read out.

206 views • 2 slides

Using Dial Indicator On a Lathe

336 views • 2 slides

Rotary Table

Mount for mill table. Clamps. Uses/ Purpose: Cutting Circular Grooves Circular hole patterns Angled Cuts. Rotary Table. Setup: 1. Mount the rotary table to the mill table 2. Find the center of the rotary table using Dial Indicator and set X and Y to zero on read out.

288 views • 2 slides