1 / 23

Read. Homework #13 and Lab #13 due next week. Quiz next week.

EET 2261 Unit 14 INCOMPLETE Analog-to-Digital Conversion (ADC ) & Digital-to-Analog Conversion (DAC ). Read. Homework #13 and Lab #13 due next week. Quiz next week. Analog Quantities. Most physical quantities (temperature, pressure, light intensity, etc.) are analog quantities.

shina
Download Presentation

Read. Homework #13 and Lab #13 due next week. Quiz next week.

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. EET 2261 Unit 14 INCOMPLETEAnalog-to-Digital Conversion (ADC) & Digital-to-Analog Conversion (DAC) • Read. • Homework #13 and Lab #13 due next week. • Quiz next week.

  2. Analog Quantities • Most physical quantities (temperature, pressure, light intensity, etc.) are analog quantities. • Transducers are devices that convert one of these physical quantities to an analog voltage or current. • Example, a temperature sensor might produce a voltage in mV that is proportional to the temperature in degrees Fahrenheit.

  3. Interfacing to the Analog World • Before a microprocessor can work on analog information, we must first use an analog-to-digital converter (ADC) to transform the analog values into digital binary values. • Conversely, we use a digital-to-analog converter (DAC) to transform digital values from the microprocessor into analog values that can be used to control analog devices. • See Chapter 12 of Floyd’s Digital Electronics for details on ADCs and DACs.

  4. A Typical Application Digital outputs Digital inputs Analog input (voltage or current) Analog output (voltage or current) ADC Micro- processor DAC . . . . . . Control physical variable Transducer Actuator Physical variable

  5. Number of Bits and Accuracy • The ADC periodically samples the analog signal, and converts each sampled value of the analog signal into a binary code. • The more bits that are used in this code, the more accurate is the representation of the original signal. • The following slides (from Floyd’s Chapter 12) show an example of how using 2 bits results in much less accuracy than using 4 bits.

  6. Figure 12.8Light gray = original waveform. Blue = Reconstructed waveform using four quantization levels (2 bits).

  7. Figure 12.10Light gray = original waveform. Blue = Reconstructed waveform using sixteen quantization levels (4 bits).

  8. Resolution • Several common ways of specifying an ADC’s resolution: • Number of bits, n • Number of output codes, = 2n, or number of steps in the output, = 2n − 1 • Percentage resolution, = 1 / (2n − 1), expressed as a percentage • Step size, = Vref / 2n

  9. Resolution: Examples

  10. ADC Hardware • Many analog-to-digital converter chips are available. • Example: the ADC0804 is a popular 8-bit ADC chip. • Our PIC chip has a built-in 10-bit ADC.

  11. The PIC Chip’s Analog Inputs • Seven of the PIC chip’s pins (labeled AN0 through AN7) can be configured as analog inputs to the chip’s internal ADC.

  12. Configuring the Analog Inputs • How do we tell the PIC chip whether we want to use these pins as analog inputs or as digital I/O? • Example: How do we tell it whether we want pin 8 to act as AN5 or as bit 0 of PORT E?

  13. Analog Inputs on the LAB-X1 • On the LAB-X1 board, three of these pins (AN0, AN1, AN3) are permanently connected to the wipers on three potentiometers.

  14. New PICBASIC Commands & Operators in Lab #4 • ADCIN command • PAUSEUS command • / operator • // operator

  15. ADCIN (p. 45 in PICBASIC manual) • Tells the PIC chip to perform an analog-to-digital conversion using its built-in A/D converter, and then saves the result of this conversion. • Example: ADCIN 0 result performs an A/D conversion on the voltage present at analog input 0, and stores the result in the variable named result. • Don’t confuse the ADCIN command with ADCON0 and ADCON1, which are special function registers on the PIC chip.

  16. PAUSEUS(p. 113 in PICBASIC manual) • Recall that the PAUSE command inserts a time delay into your program. This delay is measured in milliseconds. • Example: PAUSE 500 causes a 500 ms delay. • The PAUSEUS command is very similar, but the delay is measured in microseconds instead of milliseconds. • Example: PAUSEUS 500 causes a 500 s delay.

  17. Integer Math • Recall the difference between integers (such as 2 or 47 or 365) and floating-point numbers (such as 3.14 or 1.5 or 16.97). • PICBASIC can only deal with integers, not floating-point numbers. All math operations give integer results. • This requires us to play some tricks if we need to work with floating-point numbers.

  18. Quotient and Remainder • We know that 7÷2 = 3.5 • Recall that another way to say this is that 7÷2 = 3 with a remainder of 1. • In this example, 3 is called the quotient and 1 is called the remainder. • Another example: If you take 20÷8, what is the quotient and what is the remainder?

  19. / Operator (p. 35 in PICBASIC manual) • The / operator returns the quotient part of a division. • Example: • 7 / 2 in a PICBASIC program will return a result of 3.

  20. // Operator (p. 35 in PICBASIC manual) • The // operator returns the remainder part of a division (sometimes called the modulus). • Example: • 7 // 2 in a PICBASIC program will return a result of 1. • By using both / and //, we can keep track of both the quotient and the remainder part of a division.

  21. Integer Math in Lab #4 • Look at program called A-D Conversion3.pbp • Recall that for a 10-bit A/D conversion using a reference voltage of 5 V, the step voltage is about 4.9 mV. • So to find the voltage (in mV) corresponding to an A/D result, we need to multiply by 4.9. • But since PICBASIC can only handle integers, it can’t handle 4.9. • So instead, we multiply by 49 and then divide by 10.

  22. Integer Math in Lab #4 (Continued) • Now that we have the voltage in mV, we want to print it on the LCD in V. • Example: if the voltage = 2141 mV, then we want to print 2.141 V. • To get the part before the decimal point, take 2141 / 1000. (This returns an answer of 2.) • To get the part after the decimal point, take 2141 // 1000. (This returns an answer of 141.) • Then print those two answers, separated by a decimal point: 2.141.

  23. Another Application • For another use of these integer math tricks, see these documents in the “Documents PIC” folder on the R: shared drive: • “Convert Celsius to Fahrenheit using Integer Math.docx” • “Convert Fahrenheit to Celsius using Integer Math.docx”

More Related