1 / 37

Collimators MD: Low-level point of view

Collimators MD: Low-level point of view. AB/ATB/LPE 18/12/2006. Authors. The real work has been done by: Alessandro MASI Jerome LENDARO Arnaud BRIELMANN Mathieu DONZE Pierre GANDER Michele MARTINO FSU!!!. OUTLINE. Introduction LSS5: Architecture Problem with EM Noise Results

talmai
Download Presentation

Collimators MD: Low-level point of view

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Collimators MD:Low-level point of view AB/ATB/LPE 18/12/2006

  2. Authors • The real work has been done by: • Alessandro MASI • Jerome LENDARO • Arnaud BRIELMANN • Mathieu DONZE • Pierre GANDER • Michele MARTINO • FSU!!!

  3. OUTLINE • Introduction • LSS5: • Architecture • Problem with EM Noise • Results • TT40 • Architecture • Position Reading

  4. INTRODUCTION • We prepared two different architectures: • LSS5: • Old LEP motors, Old 2004 sensors • New control system (National Instruments PXI) • Integrated into FESA • TT40 • New non rad-hard motors • New LVDTs • Control system based PC (production Testbench). • Algorithms for position reading equivalent to what will be used in LHC • No integration into FESA (controlled through remote desktop)

  5. OUTLINE • Introduction • LSS5: • Architecture • Problem with EM Noise • Results • TT40 • Architecture • Position Reading

  6. LSS5 • Architecture • Control system based on National Instruments PXI • Power driver PARKER Gemini: will not be used for collimators but for TDI. Characteristics similar to what specified for collimators. Little bit more noisy. • Driver control based on FPGA: 5 volts TTL • Installation started the same day of MD (Oct. 31st )

  7. LSS5 • Noise Problem: • Motor current and end-stroke switches in the same cable. • Local cabling (2004) very poor quality: no shielding, cables tight together and twisted.

  8. LSS5

  9. LSS5

  10. LSS5 • Noise Problem: • Motor current and end-stroke switches in the same cable. • Local cabling (2004) very poor quality: no shielding, cables tight together and twisted. • Result: too much noise on switch signal (>5 Vpk) • Solution: • Decouple switch signal using optocouplers, excite (and read) switches at 24 volts. Noise shorted to ground with capacitors. • It took 6 hours to find the components (AB/RF, AT/MTM), mount the circuit and bring it to operation level. • It worked perfectly, no more noise at all on FPGA input.

  11. LSS5 • Lessons Learned (1/2): • As foreseen, position sensors gave unreliable reading. • Reasons: • Quality of GAP LVDT (poor linearity) • Sensor type (potentiometers) not adapted to • precision measurements over long cables • Fast cycle reading • Basically, there is nothing we can do about it. If we want better measurements, we should install baseline LHC sensors.

  12. LSS5 • Measured during test in LSS5 (Oct. 31st)

  13. LSS5 • Lessons Learned (2/2): • PXI was stable for nearly one month. • No crash, no lost connection (during crash of CMW, PXI still accessible with LabView RT) • Don’t worry, in LHC access through Labview RT will only be able to check whether the system is alive or not, no possibility to change the program or any parameter “on-line”.

  14. OUTLINE • Introduction • LSS5: • Architecture • Problem with EM Noise • Results • TT40 • Architecture • Position Reading

  15. TT40 • Architecture • Control system based on Windows PC, equipped with National Instruments motor controller and DAQ cards • Power driver PARKER Gemini. • Driver control still on 5 volts TTL • Proper cabling (all shielding properly done)

  16. TT40

  17. TT40

  18. TT40 • Lessons Learned: • Our strategy for the LHC has given excellent results concerning accuracy (see coming slides). • EM Noise is perfectly under control. No need to put optocouplers and go to 24V to get clean signals (However we will do it in the LHC to prevent even further any problem). • Remote Calibration working fine. For the LHC, we will not need to access the collimator to re-calibrate the sensors !!!! • Position reading algorithms we developed robust. A simple windows PC is sufficient to get 1 µm sigma on the measurement!!!

  19. TT40

  20. TT40

  21. TT40

  22. TT40

  23. Collimators’ requirements • Position Readout and Survey • LVDT systems (LVDT+signal conditioner) from the leading companies (Schaevitz/MSI, Sensorex, Penny & Giles) have been tested. • The results for the full system were very deceiving from different points of view: • Temperature stability is bad. Few degrees of change in temperature of the electronics may result in 200 to 300 µm change • Maintainance and portability very difficult. Each conditioner has to be manually calibrated with trimmers. We will have ~720 sensors installed in LHC. • They are all based on linear approximation of the sensor response. To go down to 5 µm resolution one would need a linearity of ~0.01%. Standard sensors are at the level of 1 to 10% linearity. • No real immunity to noise and to interference with other sensors at the input of the conditioner.

  24. Collimators’ requirements • Position Readout and Survey • All the companies contacted were ready to produce a dedicated signal conditioner to address all these points. • The first offers were very expensive and incompatible with our budget. The risk of not getting at the end what desired was also not negligible. • We therefore decided to proceed ourselves with the development of a conditioning strategy that could be conveniently applied to such a huge system.

  25. Collimators’ requirements • LVDT:

  26. Collimators’ requirements • Position Readout and Survey • After investigation on several different solutions, we chose to go for high speed sampling of the signal, and real-time processing of the data in the CPU to get the position information. • That is different from standard approach, where an analog front end electronics treats the signals before sampling

  27. Collimators’ requirements

  28. Collimators’ requirements

  29. Collimators’ requirements • To increase the immunity to Noise and Drifts, both secondaries are brought to the electronics rack.

  30. Collimators’ requirements DETECTOR ( E 1 + NOISE + DRIFT ) - ( E 2 + NOISE + DRIFT )= noise E 1 - E 2 • Noise is reduced by proper cabling

  31. Collimators’ requirements • Measured during test in LSS5 (Oct. 31st)

  32. Collimators’ requirements < 20 µm ~ 25 µm mechanical play • Measured by P. Gander during test in TT40 (Oct. 31st) in remote!!!!

  33. Collimators’ requirements • Position Readout and Survey • This result is obtained with: • 250 kS/sec simultaneous sampling of secondaries • 1000 points per acquisition • Demodulation through sin-fit algorithm (IEEE – 1241) • No additional filtering

  34. Collimators’ requirements • Position Readout and Survey • A small parenthesis on Sin-fit Algorithm • Defined by standard IEEE – 1241 as recommended method for sinus wave demodulation • Synchronous Demodulation: Allows relaxing sampling specs by using the KNOWN information about frequency of carrier (less bits, less speed). • Frequency response is a SINC: allows to have all the sensors in the same cable without interference from one to the other, and without additional filtering!!!!! (Calculated by M. Martino, University of Naples)

  35. Collimators’ requirements • Position Readout and Survey • FREQUENCY RESPONSE OF SIN FIT

  36. Collimators’ requirements • Position Readout and Survey • A small parenthesis on Sin-fit Algorithm • Frequency response is a SINC: allows to have all the sensors in the same cable without interference from one to the other, and without additional filtering!!!!! (Calculated by M. Martino, University of Naples) • That allows to transmit in the same cable, without individual shielding of the twisted pairs, all the LVDT signals. • Savings on cabling are in the order of SEVERAL 100KCHF!!!!!!

  37. Conclusions • PXI robustness demonstrated in LSS5 • Accuracy of position reading demonstrated in TT40 • Strategy chosen for Low-Level system successful !!!

More Related