ECET 340 Course Real Knowledge / ecet 340 dotcom

1. ECET 340 Course Real Knowledge / ecet340.com The Best way to predict the Future is to create it.....To Best way.... www.ecet340.com

2. ECET 340 Course Real Knowledge / ecet340.com ECET 340 Entire Course (All ilabs and Homework) (Devry) For more course tutorials visit www.ecet340.com ECET 340 Week 1 HomeWork 1 ECET 340 Week 1 iLab 1 ECET 340 Week 2 HomeWork 2 ECET 340 Week 2 iLab 2 ECET 340 Week 3 HomeWork 3 ECET 340 Week 3 iLab 3 ECET 340 Week 4 HomeWork 4

3. ECET 340 Course Real Knowledge / ecet340.com ECET 340 Week 1 HomeWork 1 (Devry) For more course tutorials visit www.ecet340.com Give three examples each of internal and external peripheral devices as referenced to the HCS12 microcontroller and not an entire PC. (2 points)2. Given “the requirements of each signal’s destination must match the capabilities of the signal’s source,” name some of the electrical signal parameters that must be considered when designing an interface between two different hardware components. (2 points)3. Write down the instructions needed to program PORT A for pins PA7, PA4-PA0 as inputs and PA6-PA5 as outputs. Answer should be a valid C language statement. (2 points)

4. ECET 340 Course Real Knowledge / ecet340.com • ECET 340 Week 1 iLab 1 (Devry) • For more course tutorials visit • www.ecet340.com • OBJECTIVES: • To become familiar with Microcontroller MC9S12 parallel ports and how simple input and output devices are interfaced through them. • To learn how to program I/O instructions in C language. • To learn how to organize a program to

5. ECET 340 Course Real Knowledge / ecet340.com ECET 340 Week 2 HomeWork 2 (Devry) For more course tutorials visit www.ecet340.com 1. Where does program control transfer to when an interrupt occurs? +2 points 2. Which one of the following Interrupts has highest priority? +2 points 3. RAM Vector table addresses $3E52 belongs to which interrupt? +2 points 4. Before exiting an ISR, the programmer should use which command? +2 points 5. In which one of the following sequences is the stack pulled by rti? +3 points 6. Given the starting address for the TC0 Interrupt is to become $5000. Write the

6. ECET 340 Course Real Knowledge / ecet340.com ECET 340 Week 3 HomeWork 3 (Devry) For more course tutorials visit www.ecet340.com 1. Sketch a circuit that can be used to debounce a pushbutton and explain how it works. (4 points max) 2. In Figure 7.32 on page 339 of the Huang textbook, if the row has and the columnsare , which key is pressed? (2 points max) 3. In Figure 7.32 on page 339 of the Huang textbook, explain why the 10kΩ resistors ties to VCC are required. (2 points max) 4. Write down the lines of C code (interrupt service routine, ISR) that generates an interrupt when Port H pin 0 becomes a logic “1”. Within this ISR, disable interrupts, clear the interrupt flag, then enable interrupts, and return from routine. I also want the routine or lines of C code that initialize Port H pin 0 to be used as an interrupt (hint: think data direction register) (2 points

7. ECET 340 Course Real Knowledge / ecet340.com • ECET 340 Week 3 iLab 3 (Devry) • For more course tutorials visit • www.ecet340.com • SOLVED ECET 340 iLAB3 • OBJECTIVES: • To learn the basic operation of a keypad. • To understand how to interface a keypad to a microprocessor. • To learn how to program a keypad driver in C language. • To learn how to program a keypad activated int

8. ECET 340 Course Real Knowledge / ecet340.com ECET 340 Week 4 HomeWork 4 (Devry) For more course tutorials visit www.ecet340.com 1. Determine the conversion time for an ADC0804 (8-bit), where 66 clocks per bit are required, if its clock frequency is 50 kHz.2. If an 8-bit SAR has Vref = 10 V, what is the binary value for an input voltage of 7.28 V?3. What is the percent error for the binary answer found in Problem #2?4. Given an 24 MHz bus speed. Write down the line(s) of instruction which set the ATD1 unit for 2MHz conversion frequency, 10-bit resolution and 8 A-to-D clocks per sample time.5. A single 10-bit, left justified conversion of 3.75V is co

9. ECET 340 Course Real Knowledge / ecet340.com • ECET 340 Week 4 iLab 4 (Devry) • For more course tutorials visit • www.ecet340.com • I. OBJECTIVES: • To learn how to use A-to-D converters to digitize signals from analog input devices. • To learn how to write a C language program that samples the data from an analog device, digitizes it and formats it for output on an LCD. • To become more proficient in programming displays for real-time operation.

10. ECET 340 Course Real Knowledge / ecet340.com ECET 340 Week 5 HomeWork 5 (Devry) For more course tutorials visit www.ecet340.com 1. Explain, briefly, why an analog restoring filter is sometimes used at the output of a DAC.2. Given Iref = 2 mA for a DAC1408 IC, find Iout for the input 1110 11103. Find the number of discrete voltages output by a 12-bit DAC. Show work.4. Use the internet to locate the data sheet for an MC1408 DAC. From it find, for the MC1408-7 version, the following:

11. ECET 340 Course Real Knowledge / ecet340.com ECET 340 Week 5 iLab 5 (Devry) For more course tutorials visit www.ecet340.com Scenario/Summary This week's lab covers two areas, conversion of digital HCS12signals to an analog format, and the use of a Serial Peripheral Interface (SPI)to transfer data, and commands between the HCS12, and the DACperipheral. Deliverables

12. ECET 340 Course Real Knowledge / ecet340.com ECET 340 Week 6 HomeWork 6 (Devry) For more course tutorials visit www.ecet340.com 1. What are the four main functions of the HC12 Timer unit?2. Two input capture events occur at counts 0x1037 and 0xFF20 of the free-running counter. How many counts (in decimal) have transpired between these two events?3. What is the maximum time possible before the free-running counter overflows when the e MHz?4. Two input capture events occur at 0x1037 and 0x002A. If the prescaler bits PR[2:1:0] are set to 101 and the e clock is 24 MHz, how much time as transpired between

13. ECET 340 Course Real Knowledge / ecet340.com The Best way to predict the Future is to create it.....To Best way.... www.ecet340.com