352-001 Exam Dumps - Pass with 352-001 Dumps PDF [2018]

1. Cisco 352-001 Exam Cisco Certified Design Expert QUESTIONS & ANSWERS (Demo Version) Thank You For Downloading 352-001 Exam PDF Demo QuizDumps helps you to prepare Cisco CCDE exam. Get most Up-to-Date Cisco 352- 001 exam Questions and Answers and pass the 352-001 exam in the first attempt. Get Full 352-001 Exam PDF Here https://quizdumps.com/exam/352-001-dumps/

2. Version: 14.0 Question 1 A company plans to include Nonstop Forwarding and Bidirectonal Forwarding Detecton as a part of their network redundancy plan. In which two ways do NSF and BFD work together when diferent hardware platorms are compared? (Choose two.) A. During supervisor engine or routng engine failover, the NSF feature will always ensure that the BFD at the peer router will not trigger a link down independent of the used hardware platorm. B. At some hardware platorms, BFD and NSF are not supported together. During supervisor engine or routng engine failover, the BFD at the peer router will trigger a link down. C. To ensure that BFD at the peer router will not trigger a link down during NSF, the BFD packets must be processed fast enough, and, during supervisor engine or routng engine failover, by processing the BFD independent from the supervisor engine or routng engine. D. Because BFD is always processed at the line cards (not at the supervisor engine or routng engine), a supervisor engine or routng engine failover will not afect the BFD peer router. E. Because BFD is always processed at the supervisor engine or routng engine, a supervisor engine or routng engine failover will always trigger a link down at the peer router. Aoswern BC Question 2 Refer to the exhibit. A service provider would like to use Ethernet OAM to detect end-to-end connectvity failures between SP-SW1 and SP-SW2. In which two of these ways can you design this soluton? (Choose two.) A. Enable Y.1731 Connectvity Fault Management on the SP switches. B. E-LMI PDUs must be forwarded over VPLS. C. Cisco Discovery Protocol PDUs must be forwarded over the VPLS. D. Use upward maintenance endpoints on the SP switches. E. Enable IEEE 802.1ag Connectvity Fault Management on the SP switches. Aoswern DE Question 3

3. A network design shows two routers directly connected to an Ethernet switch using optcal connectons. There is an OSPF adjacency between the routers. In this design, which soluton will ensure that interface down detecton is reported as quickly as possible to the IGP? A. optmiied OSPF SPF tmers B. Bidirectonal Forwarding Detecton C. automatc protecton switching D. optmiied OSPF LSA tmers E. Ethernet OAM CFM monitoring Aoswern B Question 4 A network designer is working with a company to improve convergence at the Layer 2 control plane and decides to use LACP. Which of these components does LACP use to create the system ID? A. LACP system priority and switch MAC address B. LACP port priority and switch MAC address C. LACP port priority and port number D. LACP system priority and port number Aoswern A Question 5 How are community formats sent in SNMPv1 and SNMPv2c? A. In both protocols they are encrypted. B. In both protocols they are sent as clear text. C. In SNMPv1 they are sent as clear text and in SNMPv2c they are encrypted. D. In SNMPv1 they are sent as clear text and in SNMPv2c they are sent as part of an encrypted session. Aoswern B Question 6 You are deploying OSPF on a point-to-multpoint Frame Relay network. The remote sites do not need to be able to communicate with each other and there are a relatvely small number of sites (scaling is not a concern). How should you confgure OSPF for this topology to minimiie the additonal routng informaton injected into the network and keep the confguraton siie and complexity to a minimum? A. Confgure the link at the hub router as OSPF point-to-multpoint and at the remote routers as OSPF point-to-point.

4. B. Confgure the link as OSPF broadcast and confgure the hub router to always be the designated router. C. Confgure the link as OSPF nonbroadcast and manually confgure each of the remote sites as a neighbor. D. Confgure the link as OSPF broadcast and confgure a mesh group towards the remote routers. Aoswern B Question 7 Which two practces should you implement to increase SNMPv1 security? (Choose two.) A. Restrict access to the specifc SNMP engine IDs in use. B. Use ACLs to allow only specifc IP addresses to poll SNMP. C. Use a combinaton of alphanumeric characters for the community strings. D. Use SNMP encrypton for transport confdentality. Aoswern BC Question 8 Refer to the exhibits. You have been asked to review a proposal for adding redundancy to the non-redundant network in Exhibit 1. Exhibit 2 shows the proposed redundant network. Which technology would provide faster convergence over the newly introduced layer 2 domains? A. Bi-directonal Forwarding Detecton B. Rapid Spanning Tree C. Unidirectonal Link Detecton D. Hot Standby Router Protocol

5. Aoswern A Question 9 A service provider has a Resilient Ethernet Protocol ring running as a metro backbone between its locatons in one city. A customer wants to connect one site with one box redundant to the Resilient Ethernet Protocol ring at two diferent service provider locatons. How can this be done without producing any Layer 2 loops within the network design? A. Spanning tree at the service provider side only must be enabled. B. Spanning tree at the customer side only must be enabled. C. Flex Links at the service provider side only must be enabled. D. Flex Links at the customer side only must be enabled. E. EtherChannel at the service provider side and the customer side must be enabled. F. Spanning tree at the service provider side and the customer side must be enabled. G. Flex Links at the service provider side and the customer side must be enabled. Aoswern D Question 10 Refer to the exhibit. Your company designed a network to allow server VLANs in a data center to span all access switches. In the design, Layer 3 VLAN interfaces and HSRP are confgured on the aggregaton switches. In which three

6. ways should the design of the STP domain be optmiied for server and applicaton performance? (Choose three.) A. Use loop guard on access ports. B. Use PortFast on access ports. C. Use root guard on access ports. D. Align Layer 2 and Layer 3 forwarding paths. E. Use BPDU Skew Detecton on access ports. F. Explicitly determine root and backup root bridges. Aoswern BDF Question 11 You have created a network design that has two point-to-point Metro Ethernet circuits extending a single producton VLAN between two data centers. Under normal circumstances, one circuit will carry trafc and spanning tree will block the other. If the company wants you to make use of both circuits to carry producton trafc, which two technologies and features will you investgate to integrate into your network design? (Choose two.) A. EtherChannel B. MST C. Multchassis EtherChannel D. PVST+ Aoswern AC Question 12 Refer to the exhibit.

7. Acme Corporaton hired you as a network designer to upgrade their network so that it supports IPv4 and IPv6 multcast. Which two protocols are needed on the LAN switch? (Choose two.) A. PIM sparse mode B. IGMP snooping C. PIM snooping D. Source Specifc Multcast E. MLD snooping Aoswern BE Question 13 Voice trafc between two campus enterprise networks is growing. The network designers decide to add a second 10-Mb Metro Ethernet service parallel to their original 10-Mb service in order to provide more bandwidth and diversity. The QoS profle will be the same on the new 10-Mb service due to the voice stability on the frst Metro Ethernet link. When the second link is added to the OSPF domain, which trafc design consideraton would have the most impact on the voice trafc when both links are actve?

8. A. per-destnaton IP address basis B. per-fow basis C. per-packet basis D. per-source IP address basis Aoswern C Question 14 You work as a network designer for a company that is replacing their Frame Relay WAN with an MPLS VPN service, where the PE-to-CE routng protocol is BGP. The company has 3000 routes in their distributon routers, and they would like to advertse their access routers through the MPLS network. Their service provider, however, only supports 1000 prefxes per VRF. Which two design solutons can be applied to ensure that your access routers will be able to reach all devices in your network? (Choose two.) A. Use prefx lists on your distributon routers to control which routes are sent to the MPLS network. B. On your distributon routers, confgure null routes and aggregate routes for the prefxes in your network. C. Confgure your distributon routers to send a default route to the MPLS network. D. Summariie the routes on the MPLS WAN interfaces of your distributon routers. Aoswern BC Question 15 You are designing a network that will run EIGRP over a Metro Ethernet service that does not employ a link-loss technology. What will be the impact on convergence if there is a break in the end-to-end Layer 2 connectvity within the service provider network? A. The routers will immediately lose their adjacencies and converge. B. The routng protocol will not converge untl the hold tmers have expired. C. The switch ports connected to the router will go down and the routers will immediately converge. D. The VLAN on the switches will go inactve, the ports associated on the switch will go down, and the routers will immediately converge. Aoswern B Question 16 A new video multcast applicaton is deployed in the network. The applicaton team wants to use the 239.0.0.1 multcast group to stream the video to users. They want to know if this choice will impact the existng multcast design. What impact will their choice have on the existng multcast design? A. Because 239.0.0.1 is a private multcast range, a food of PIM packets that have to be processed by the

9. CPU and hostswill be sent by the routers in the network. B. Because 239.0.0.1 is a private multcast range, the rendeivous point has to send out constant group updates that will have to be processed by the CPU and hosts. C. The multcast applicaton sends too many packets into the network and the network infrastructure drops packets. D. The 239.0.0.1 group address maps to a system MAC address, and all multcast trafc will have to be sent to the CPU and fooded out all ports. Aoswern D Question 17 Refer to the exhibit. In this design, which technology would provide for the best use of resources to provide end-to-end Layer 2 connectvity? A. MSTP B. PAgP C. Multchassis EtherChannel D. LACP Aoswern C Question 18

10. A customer is using a service provider to provide a WAN backbone for a 30-site network. In establishing the network, the customer must work within these constraints: The customer has a self-managed MPLS backbone. The VPLS WAN backbone of the service provider does not support PIM snooping. Multcast VPN must be used for multcast support inside some VRFs. What can the customer do so that multcast trafc is NOT fooded to all sites? A. Confgure statc GRE tunnels and run the MPLS and multcast VPN inside these GRE tunnels. B. Use Label Switched Multcast for the multcast transport. C. Use PIM-SSM as the multcast routng protocol with IETF Rosen Draf multcast VPN. D. Confgure a statc mapping between multcast addresses and MAC addresses. E. Use GET VPN to encrypt the multcast packets inside the WAN. Aoswern A Question 19 What are two design advantages to using virtual port channel? (Choose two.) A. enhanced system availability through multple systems B. reduced Spanning Tree Protocol convergence tme C. loop management without use of Spanning Tree Protocol D. ability to use Spanning Tree Protocol blocked ports to forward trafc E. enhanced ability to recover from Spanning Tree Protocol changes Aoswern AC Question 20 Refer to the exhibit. In this network, all routers are confgured to run EIGRP on all interfaces. All interface bandwidths are set to 1000, and the delays are confgured as shown. In the topology table at Router C, you see only one path towards 10.1.1.0/24. What is the reason that Router C only has one path in its topology table?

11. A. Router D is not advertsing 10.1.1.0/24 to Router C because Router C is its feasible successor. B. Router B is not advertsing 10.1.1.0/24 to Router C because Router C is its feasible successor. C. Router D is not advertsing 10.1.1.0/24 to Router C due to split horiion. D. Router B is not advertsing 10.1.1.0/24 to Router C due to split horiion. Aoswern C Question 21 Refer to the exhibit. All routers in this network are confgured to place all interfaces in OSPF area 5. R3 is the designated router on the 10.1.5.0/24 network. If you examine the OSPF database on R4, what would the network (type 2) LSA, generated by R3, contain? A. a connecton to 10.1.5.0/24 and links to R3, R2, and R1 B. a connecton to 10.1.5.0/24 and links to R2 and R1 C. connectons to 10.1.5.0/24 and 10.1.1.0/31 D. no connectons, R3 does not generate a network (type 2) LSA in this network Aoswern A Question 22 Refer to the exhibit.

12. Which routes in this network will be installed in the routng table at router E? A. the OSPF route B. the EIGRP route C. the OSPF and EIGRP routes D. neither the OSPF nor the EIGRP route Aoswern C Question 23 An enterprise network manager has decided to dual-home two service providers for Internet connectvity. In order to provide optmal outbound routng, the full Internet routng table will be accepted from each provider. The enterprise has obtained address space and an AS to use in connectng to the Internet. What is the simplest mechanism the network manager can use to prevent it from becoming a transit between the two service providers? A. Build a route flter that only allows the specifc networks the enterprise owns to be advertsed to each of the service providers. B. Build a trafc flter that only allows trafc originatng from the specifc networks the enterprise owns to be forwarded towards the service providers. C. Build a route flter that only allows networks with an empty AS path to be advertsed to each of the service providers. D. Build a route flter that only allows networks which are tagged with the LOCAL community to be advertsed to each of the service providers. Aoswern C

13. Question 24 Which statement correctly describes how MTU mismatches are addressed in the IS-IS neighbor- formaton process? A. IS-IS checks the locally confgured MTU against the MTU advertsed in neighbor hello packets. B. IS-IS checks the locally confgured MTU against the MTU advertsed in neighbor LSPs. C. IS-IS does not check for MTU mismatches when forming a neighbor relatonship. D. IS-IS pads hellos, so neighbor relatonships will not be formed on links with mismatched MTUs. Aoswern D Question 25 Which statement is true about connectng an IP multcast domain that is operatng in PIM dense mode to a PIM sparse mode domain? A. The interconnecton must be made at the rendeivous point of the PIM sparse mode domain. B. The connecton can be made at any locaton in the network, as PIM sparse mode will inter-operate seamlessly with PIM dense mode. C. PIM dense mode and sparse mode domains are not inter-operable and cannot be connected. D. The connecton can be made at any locaton in the network, but PIM sparse mode and PIM dense mode cannot inter-operate; IGMP must be used to provide the interconnecton. Aoswern A

14. QuizDumps CCDE professionals and Cisco specialist provide you verified Cisco 352-001 exam dumps. Our 352-001 PDF questions come with 100% money back guarantee. QuizDumps have already helped 100s of certification% 352-001 students in passing 352-001 exam with high marks in first attempt. In case of faliur you can get your money back. (Start Your 352-001 Exam Prepration Now) Download All 352-001 Questions From https://quizdumps.com/exam/352-001-dumps/ 100% Guaranteed Success in 352-001 Exam.