1 / 14

OpenFlow Global Configuration

OpenFlow Global Configuration. G 8264 is capable to operate either in Normal Switching mode and Openflow Switching mode Global state is maintained to activate Openflow Switch RS G8264( config )# openflow ? Configure Open Flow general configuration

alden
Download Presentation

OpenFlow Global Configuration

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. OpenFlow Global Configuration G8264 is capable to operate either in Normal Switching mode and OpenflowSwitching mode Global state is maintained to activate Openflow Switch RS G8264(config)#openflow ? Configure Open Flow general configuration buffer Enable buffer support for oflow packets enable Enable Open Flow ======== Should be ON fdb configure fdb priority commands maxflow Set Open Flow Max. Limit table Add/Modify/Delete Flows RS G8264(config)#openflow

  2. OpenFlow VLAN Configuration VLAN which needs to be part of Openflow Network needs to be enabled and configured with OpenflowIdentifier. RS G8264(config-vlan)#? VLAN configuration mode enable Enable the current VLAN exit Exit from VLAN configuration mode member VLAN member name VLAN name no Negate commands openflow Open Flow VLAN Configuration commands ==== openflowconfig openflow-id Set the Open Flow ID for VLAN == openflow identifier private-vlan Configure private VLAN protocol-vlan Configure protocol VLAN stg Assign VLAN to a Spanning Tree Group vmap Add a vmap RS G8264(config-vlan)#

  3. RS G8264(config-vlan)#openflow ? Open Flow VLAN Configuration commands connect Configure controller connection commands controller Configure controller for Open Flow VLAN  Controller config echo-reply Configures retention period for echo-request message echo-request Configures transmission interval for echo-request messages emergency Configure emergency timeout RS G8264(config-vlan)#openflow

  4. Openflow Controller Configuration RS G8264(config-vlan)#openflow controller 1 ? address Set controller IP Address port Set controller listening port number RS G8264(config-vlan)# RS G8264(config-vlan)#openflow controller 1 address 172.20.254.248 ? data-port Data port  Controller is connected to dataports 1-64 mgt-port Management port  Controller is connected to mgmt port 65 <cr>

  5. Openflow Port Configuration To configure ports as edge-ports (MAC Learning is ON) RS G8264(config)#openflow-edgeport ? LINE Add port(s) delimited by ',' or an interval of ports delimited by '-‘ To configure ports as data-management to connect controller via dataports (Not part of Openflow data network) RS G8264(config)#openflow-mgmtport ? LINE Add port(s) delimited by ',' or an interval of ports delimited by '-'

  6. Openflow Switch Configuration RS G8264(config)#show running-config Current configuration: ! version "1.0.0.43" switch-type "Blade Network Technologies RackSwitch G8264" ! openflow enable ! no system bootp system idle 30 ! ! interface port 2 no learning pvid 2 flood-blocking exit ! interface port 3 no learning pvid 2 flood-blocking exit ! interface port 4 no learning pvid 2 flood-blocking exit ! interface port 5 no learning pvid 2 flood-blocking exit

  7. ! vlan 1 name "ibm" member 1,6-64 no member 2-5 ! vlan 2 enable name "VLAN 2" member 2-5 openflow controller 1 address 172.20.254.248 openflow controller 1 port 6444 openflow-id 9 ! ! spanning-tree stp 1 vlan 1 spanning-tree stp 1 vlan 2 spanning-tree stp 1 vlan 4095 interface port 2 no spanning-tree stp 1 enable exit ! interface port 3 no spanning-tree stp 1 enable exit ! interface port 4 no spanning-tree stp 1 enable exit ! interface port 5 no spanning-tree stp 1 enable exit ! end

  8. Openflow Show Commands RS G8264(config)#show openflow ? <1-16> Open Flow ID  Shows supported OF features sent to controller statistics Show Open Flow Statistics  Shows statistics table Show Open Flow Table  Shows basic table and emergency tables <cr> RS G8264(config)#show openflow Protocol Version: 1 Openflow State: enable Max Flows: 10000 FDB Table Priority: 1000 Open Flow Instance ID: 9 OpenflowEdgeports : None OpenflowManagementports : None Openflow Buffering : Disabled RS G8264(config)#

  9. RS G8264(config)#show openflow 9 Open Flow Instance ID: 9 DataPath ID: 0x2fccf629d4500 Vlan ID: 2 Max Retries per controller: 4 Echo Request Interval: 30 Echo Reply Timeout: 15 Emergency Timeout: 30 Operational Mode: Emergency Miss Send Len: 128 Swicth Support Capabiilities: Flow Statistics : enabled Table Statistics : enabled Port Statistics : enabled Spanning Tree : disabled Reserved : disabled Reassemble IP Fragments : disabled Queue Statistics : disabled Match IP Addr in ARP Packets: disabled Swicth Support action: Output to Switch Port : enabled Set Vlan ID : enabled Set Priority : enabled Strip dot1q Header : disabled Ethernet Source Addr : enabled Ethernet Destination Addr: enabled IP Source Address : disabled IP Destination Address : disabled IP ToS : enabled TCP/UDP Source Port : disabled TCP/UDP Destination Port : disabled Output to Queue : disabled Vendor : disabled

  10. PortList Status State Config Current Advertised Supported Peer • 2 d 0x201 0x2 0x40 0x0 0x00x0 • 3 d 0x201 0x2 0x40 0x0 0x00x0 • 4 d 0x201 0x2 0x40 0x0 0x00x0 • 5 d 0x201 0x2 0x40 0x0 0x00x0 • Number of Ports: 4 • Configured Controllers: • IP Address: 172.20.254.248 • State: Inactive • Port: 6444 • Retry Count: 4 • Configured Controller Count 1 • RS G8264(config)#

  11. RS G8264(config)#show open statistics Dumping Open Flow stats Flow Count Basic Flows: 97750 (ACL Based: 750, FDB Based: 97000) Emergency Flows: 1000 (ACL Based: 750, FDB Based: 250) Message Count Hello-Sent: 2 Hello-Recvd: 2 Echo-Request-Sent: 2 Echo-Request-Recvd: 0 Echo-Reply-Sent: 0 Echo-Reply-Recvd: 2 Feature-Request: 0 Feature-Reply: 0 Get-Config-Request: 0 Get-Config-Reply: 0 Set-Config: 0 Packet-In No-Match: 0 Action: 0 Flow-Removed: Idle-Timeout: 0 Hard-Timeout: 0 Delete: 0

  12. Port-Status: • Add: 0 • Delete: 0 • Modify: 0 • Packet-Out: 0 • Flow-Mod: • Add: 98750 • Modify: 0 • Modify-Strict: 0 • Delete: 0 • Delete-Strict: 0 • Port-Mod: 0 • Statistics-Request: • Desc: 0 • Flow: 0 • Aggregate: 0 • Table: 0 • Port: 0 • Statistics-Reply: • Desc: 0 • Flow: 0 • Aggregate: 0 • Table: 0 • Port: 0 • Barrier-Request: 0 • Barrier-Reply: 0

  13. Error Messages • Hello Failed Sent: • Incompatible: 0 • Hello Failed Recv: • Incompatible: 0 • Bad Request: • Bad-Version: 0 • Bad-Type: 0 • Bad-Stat: 0 • Buffer-Unknown: 0 • Bad Action: • Bad-Out-Port: 0 • Flow-Mod-Failed: • All-Table-Full: 0 • Overlap: 0 • Emergency-Timeout: 0 • Bad-Command: 0 • Unsupported: 0 • Port-Mod-Failed: • Bad-Port: 0 • RS G8264(config)#

  14. Show openflow table BASIC FLOW TABLE Flow:1 Filter Based, priority:32768, hard-time-out: 0, idle-time-out: 0 QUALIFIERS: ingress-port:15 ACTION: set_nw_tos=28(28), output:4 STATS: packets=0, bytes=0 Flow:2 Filter Based, priority:65535, hard-time-out: 0, idle-time-out: 0 QUALIFIERS: ingress-port:31, vlan-id: 14, vlan-priority: 4, ether-type:0x806 src-mac:00-00-00-00-12-13, dst-mac:00-00-00-00-14-16, arp-type:128 src-ip:1.2.3.4/32 ACTION: set-vlan-id=20, set_nw_tos=32(35), output:2, 3, 4, 5, 6, 7, 8 STATS: packets=0, bytes=0 Flow:3 FDB Based, priority: 1000, hard-time-out: 0 QUALIFIERS: dst-mac:01-00-00-00-00-03, vlan-id: 1 ACTION: out-port: 2, 3, 4, 5, 6, 7, 8, 9, 10 EMERGENCY FLOW TABLE Flow:1 Filter Based, priority:65535, hard-time-out: 0, idle-time-out: 0 QUALIFIERS: ingress-port:31, vlan-id: 14, vlan-priority: 4, ethertype: 0x806 src-mac:00-00-00-00-12-13, dst-mac:00-00-00-00-14-16, arp-type:128, src-ip:1.2.3.4/32 ACTION: set-vlan-id=20, set_nw_tos=32(35), output:2, 3, 4, 5, 6, 7, 8

More Related