1 / 22

JMDC Command Files for Activation and Operation 2011-03-04 AMS SW Review, KSC, Mar. 2011

JMDC Command Files for Activation and Operation 2011-03-04 AMS SW Review, KSC, Mar. 2011. Andreas Sabellek. Supported by the Carl-Zeiss-Foundation. Command Files for Activation Overview. start_up.cmd Executed whenever JAP is loaded cfg_xxxx.cmd (configuration file) Executed on request

avon
Download Presentation

JMDC Command Files for Activation and Operation 2011-03-04 AMS SW Review, KSC, Mar. 2011

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. JMDC Command Filesfor Activation and Operation2011-03-04AMS SW Review, KSC, Mar. 2011 Andreas Sabellek Supported by the Carl-Zeiss-Foundation

  2. Command Files for Activation Overview • start_up.cmd • Executed whenever JAP is loaded • cfg_xxxx.cmd (configuration file) • Executed on request • configuration dependent command list (e.g. ESTEC AA) • One of out of the present configuration command files is executed by the startup command file (defined individually on every JMDC) • rst_xxxx.cmd (file to restore JMDC to DAQ) • Execute on request to set JAP to DAQ operation after JAP needed to be reloaded during DAQ AMS SW Review, KSC

  3. Current start_up.cmd • Optionally change high rate data output rate • default JAP settings are kept (HRDL: 9Mbit/s; RS422: 1.92 MHz) • Start CQ-List task • Enable additional CHD data pages • Task status added for debugging • Executes a configuration command file AMS SW Review, KSC

  4. cfg_xxxx.cmd execution sets 1) Node Address Table cfg_xxxx.cmd 2) CQ-List Items (disabled) 3) Table of Dallas temperature sensors and actions for monitoring task 4) Activation/Deactivation (powerstep) command lists Configuration is packed into one file AMS SW Review, KSC

  5. 1) Node Address Table • Sets AMSWire paths • Sets CAN bus addresses and bus • Assigns primary and secondary alias addresses • Minor changes (to tested table) are done by separate commands AMS SW Review, KSC

  6. 2) CQ-List Items • Items are added with primary node address, in this way the real path is defined by node address table • Current items monitor • Slow Control: JPD, M-Crate, CCEB, PDS, TTCE, UG, GPS*, ASTE* • DAQ nodes: JLV1, T, E, R, S, U • Items during DAQ operation: T, E (dyn. pedestals) AMS SW Review, KSC

  7. 3) DTS Table • Includes all sensors connected to busses on JPD, M-crate, CCEB, PDS (on USCM), UG • Sets warning and alarm limits for every sensor (counted in CHD data) • Sets command to be executed, when alarm limit is reached (may be configuration dependent) AMS SW Review, KSC

  8. 4) Powerstep Command Lists Overview powerstep 0: no switching of power, but enables monitoring of hardware powered when 120V to PDS is applied; executed by JAP on power on powerstep 1: ends in STANDBY condition; powers on slow control hardware and enables monitoring powerstep 2: powers on detectors except tracker; high voltage stays off and monitoring is enabled powerstep 3: powers on tracker and start tracker thermal interlock task and enables monitoring powerstep 4: ramping of high voltages for detectors powerstep 5: ends in OPERATIONAL condition; sets and starts DAQ powerstep 6: stops DAQ and prepares repeated execution of powersteps powerstep 7: ends in STANDBY condition; powers off detectors and leaves slow control hardware on AMS SW Review, KSC

  9. Powerstep 0 Summary • Reset all node address table errors • Boot PDS USCM, enable qlist item, start PDS task • Boot JPD USCM, enable qlist item, start GTSN task • Enable JLV1 qlist item • Set JLV1 and JINJ nodes in DAQ wishlist • Read PDS status AMS SW Review, KSC

  10. Powerstep 1 Summary • Switch off PDS and JPD secondary USCM • Switch on all 28V DC/DC (PB2) in PDS • M-Crate List: power MPD, boot USCM, secondary USCM off, boot ASTE, enable qlist item • TTCE List: power TTPD, enable qlist item • UG List: power UGPD, boot USCM, secondary USCM off, configure UG, start UG task, enable qlist items • Enable heaters according to STANDBY condition • Read PDS status AMS SW Review, KSC

  11. Powerstep 2 Summary • ToF list: power on SPDs, enable qlist items, enable nodes in DAQ wishlist • TRD list: power on UPDs, load configuration files, enable qlist items, secondary JINFs off, enable nodes in DAQ wishlist • RICH list: power on ERPDs, load configuration files, enable qlist items, secondary JINFs off, enable nodes in DAQ wishlist • ECAL list: (power on ERPDs), load configuration files, enable qlist items, secondary JINFs off, enable nodes in DAQ wishlist • Read PDS status AMS SW Review, KSC

  12. Powerstep 3 Summary • Start Tracker Thermal interlock task • power on TPDs • Perform TPD DC/DC converter configuration procedure and load configuration files • enable qlist items • secondary JINFs off • enable nodes in DAQ wishlist • Enable heaters according to OPERATIONAL condition • Read PDS status AMS SW Review, KSC

  13. Powerstep 4 Summary • TOF list: load configuration files for high voltage • TRD list: start routine to ramp high voltage • RICH list: load configuration files for high voltage • ECAL list: load configuration files for high voltage AMS SW Review, KSC

  14. Powerstep 5 Summary • (Start Startracker DAQ) • (Switch off not used JINJs, JLV1 and JPD) • Enable DAQ qlist items for ECAL, Tracker • Set DAQ parameters • Set TAS Run parameters • Set Tracker secondstep calibration parameters • Start DAQ AMS SW Review, KSC

  15. Powerstep 6 Summary • Stop DAQ • Switch on all JMDC, JINJ, JLV1 and both JPD • All secondary JINF nodes on • All secondary USCM nodes on • Reset all errors in node table AMS SW Review, KSC

  16. Powerstep 7 Summary • Stop DAQ • Switch on all JMDC, JINJ, JLV1 and both JPD • Disable qlist items for S,U,T,R,E • Power off xPDs for S,U,T,R,E • Set JLV1 and JINJ nodes in DAQ wishlist • Enable heaters according to STANDBY condition • Read PDS status AMS SW Review, KSC

  17. rst_xxxx.cmd • Ends in OPERATIONAL condition (powerstep 0-5 command list previously executed) for JMDC • Execute cfg_xxxx.cmd • Configure and start JMDC tasks • Enable CQ-list items • Configure and start DAQ • Remark: Cannot be used to restore STANDBY condition for JMDC! After reloading JAP in STANDBY execute powerstep command lists 0 and 1. AMS SW Review, KSC

  18. Prepared Configuration Command Files Files updated March 3rd, 2011 to match new JAP AMS SW Review, KSC

  19. Availability of Current Command Files • Local on pcposk0:/pocchome/jmdc/Startup_FM/ • Web on http://ams.cern.ch/AMS/DAQ/ams02_cmds/ • Directory summary /: startup files, configuration files, restore DAQ files /QLIST: command lists for every node, item numbers assigned in qlist.txt /NODES: node tables /GTSN: sensor tables /POWERSTEPS: powerstep command lists • Remarks: • filenames in these locations are extended for better description of contents… but for clearness can be changed to 8-byte name as in JMDC • All command parameters are available as readable textfiles now • Currently programs by X.Cai are used to make binaries AMS SW Review, KSC

  20. Activation/Deactivation Example (Procedure) • All steps follow checklists maintained by M.Capell with more intermediate checks and actions AMS powered on PDS side A and JAP is loaded on JMDC-1 • Execute cfg_BB00.cmd • Execute powerstep 0 and 1 (AMS is in STANDBY) • Execute powerstep 2, 3 and 4 (monitoring and detectors are on) • Execute powerstep 5 (DAQ operation) JAP gets reloaded • Execute rst_BB00.cmd (DAQ operation) After some time… • Execute powerstep 7 (AMS in STANDBY) Power off AMS AMS SW Review, KSC

  21. List of Other Command Files • cceb_on: powers CCEB on and enables reading of CCBT • cceb_off: powers CCEB off and disables cq-list item • tas(t): TAS run command file (to be erased?) • tof_scan: File with 12 different ToF HV settings in preparation • ugx_vcls: TRD gas operation Additional files need to be prepared/verified for tomorrow? AMS SW Review, KSC

  22. Plans • Currently command lists of powersteps and qlist items are based on individual input from subdetector groups, which should be reviewed and matched • Develop (GUI) editor program to allow reliable modification of files (to be tested on FS) AMS SW Review, KSC

More Related