1 / 16

Sliding Wear of Tungsten-Carbide Thermal Spray Coatings Standard Grind and Superfinished

Sliding Wear of Tungsten-Carbide Thermal Spray Coatings Standard Grind and Superfinished. HCAT Meeting August 28 – 30, 2001 Toronto, Ontario, Canada. SOUTHWEST Aeroservice, Inc. Outline. Objectives Experimental Procedure Wear Test Schematic and Machine Specimens Results.

baylee
Download Presentation

Sliding Wear of Tungsten-Carbide Thermal Spray Coatings Standard Grind and Superfinished

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Sliding Wear of Tungsten-Carbide Thermal Spray CoatingsStandard Grind and Superfinished HCAT Meeting August 28 – 30, 2001 Toronto, Ontario, Canada SOUTHWEST Aeroservice, Inc.

  2. Outline • Objectives • Experimental Procedure • Wear Test Schematic and Machine • Specimens • Results SOUTHWEST Aeroservice, Inc.

  3. Objectives • Compare sliding wear characteristics of standard grind thermal spray coatings to superfinished coatings. • Compare sliding wear characteristics of thermal spray coatings to chrome plating – standard grind and superfinished. SOUTHWEST Aeroservice, Inc.

  4. Experimental Procedure • Perform sliding wear test according to ASTM G77 standard • Quantify wear for each coating type and chrome plating (standard grind and superfinished) against Al-Ni-Bz bearing material • Standard grind finish defined as 16 –32 Ra • Superfinish defined as 4 Ra or less SOUTHWEST Aeroservice, Inc.

  5. w ASTM G77 Wear Test Schematic The thermal spray coated test ring rotates against a stationary Al-Ni-Bz test block with a 15 1b contact force. Boeing grease BMS 3-33 was used as lubricant between block and ring. SOUTHWEST Aeroservice, Inc.

  6. Wear Test Machine Load Cell Block Ring SOUTHWEST Aeroservice, Inc.

  7. Wear Test Procedure • Weigh ring and block before test • Install ring, block, and grease feeder • Run test for 30 min with load applied – 6.8 kg (15-lb) • Clean off grease from ring and block • Weigh ring and block after test • Measure volume loss from blocks SOUTHWEST Aeroservice, Inc.

  8. Wear Test Procedure • Quantify volume loss from block by measuring width of scar Al-Ni-Bz Block SOUTHWEST Aeroservice, Inc.

  9. Wear Test Specimens SOUTHWEST Aeroservice, Inc.

  10. Wear Test Specimens • Rings (1.377 in dia. coated on O.D.) • Coatings • SWATS 125 • SWATS 076 • SWATS 139 • SWATS 141 • SWATS 140 SOUTHWEST Aeroservice, Inc.

  11. Wear Test Specimens • Blocks (0.625 x 0.40 x 0.25 in) • Al-Ni-Bz (Common aircraft bearing material) • Also Coatings • SWATS 125 • SWATS 076 • SWATS 139 • SWATS 141 • SWATS 140 SOUTHWEST Aeroservice, Inc.

  12. Wear Test Results SOUTHWEST Aeroservice, Inc.

  13. Wear Test Results SOUTHWEST Aeroservice, Inc.

  14. Wear Test Results SOUTHWEST Aeroservice, Inc.

  15. Wear Test Results SOUTHWEST Aeroservice, Inc.

  16. This is a preliminary report of findings. T.U. will be presenting the complete results at the ASM International Materials Solutions Conference in Indianapolis on Wednesday November 7, 2001. SOUTHWEST Aeroservice, Inc.

More Related