1 / 39

ITGD4103 Data Communications and Networks Lecture-13: SONET/SDH week 13- q-2/ 2008

University of Palestine. Faculty of Information Technology. ITGD4103 Data Communications and Networks Lecture-13: SONET/SDH week 13- q-2/ 2008. Dr. Anwar Mousa. SONET / SDH. What is SONET & SDH?.

benedict-kirby
Download Presentation

ITGD4103 Data Communications and Networks Lecture-13: SONET/SDH week 13- q-2/ 2008

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. University of Palestine Faculty of Information Technology ITGD4103 Data Communications and Networks Lecture-13: SONET/SDH week 13- q-2/ 2008 Dr. Anwar Mousa

  2. SONET / SDH

  3. What is SONET & SDH? • SONET and SDH are a set of related standards for synchronous data transmission over fiber optic networks. • SONET is short for Synchronous Optical NETwork • SDH is an acronym for Synchronous Digital Hierarchy. • SONET is the United States version of the standard published by the American National Standards Institutue (ANSI). • SDH is the international version of the standard published by the International Telecommunications Union (ITU).

  4. The following table lists the hierarchy of the most common SONET/SDH data rates: • Optical Level Electrical Level Line Rate (Mbps) SDH Equivalent • OC-1 STS-1 51.840 – • OC-3 STS-3 155.520 STM-1 • OC-12 STS-12 622.080 STM-4 • OC-48 STS-48 2488.320 STM-16 • OC-192 STS-192 9953.280 STM-64 • OC-768 STS-768 39813.120 STM-256 • OC-1536 STS-1536 79,626,120 STM-512 • OC-3072 STS-3072 159,252,240 STM-1024 • STS (electrical signaling levels called Synchronous Transport Signals) • OC: Optical Carrier • STM: Synchronous Transport Modul

  5. The SONET/SDH • The "line rate" refers to the raw bit rate carried over the optical fiber. • A portion of the bits transferred over the line are designated as "overhead". • The overhead carries information that provides OAM&P (Operations, Administration, Maintenance, and Provisioning) capabilities such as framing, multiplexing, status, and performance monitoring. • The "line rate" minus the "overhead rate" yields the "payload rate" which is the bandwidth available for transferring user data such as packets or ATM cells.

  6. The SONET/SDH// • The SONET/SDH level designations sometimes include a "c" suffix (such as "OC-48c"). • The "c" suffix indicates a "concatenated" or "clear" channel. • This implies that the entire payload rate is available as a single channel of communications (i.e. the entire payload rate may be used by a single flow of cells or packets). • The opposite of concatenated or clear channel is "channelized". • In a channelized link the payload rate is subdivided into multiple fixed rate channels. • For example, the payload of an OC-48 link may be subdivided into four OC-12 channels.

  7. The SONET/SDH • In practice, the terms STS-1 and OC-1 are sometimes used interchangeably, though the OC-N format refers to the signal in its optical form. • It is therefore incorrect to say that an OC-3 contains 3 OC-1s: an OC-3 can be said to contain 3 STS-1s. • Note that the typical data rate progression starts at OC-3 and increases by multiples of 4. • As such, while OC-24 and OC-1536, along with other rates such as OC-9, OC-18, OC-36, and OC-96 may be defined in some standards documents, they are not available on a wide-range of equipment. • As of 2007, OC-3072 is still a work in progress.

  8. The SONET/SDH • Synchronous optical networking, is a method for communicating digital information using lasers or light-emitting diodes (LEDs) over optical fiber. • The method was developed to replace the Plesiochronous Digital Hierarchy (PDH) system for transporting large amounts of telephone and data traffic • and to allow for interoperability between equipment from different vendors.

  9. The SONET/SDH • Synchronous networking differs from PDH in that the exact rates that are used to transport the data are tightly synchronized across the entire network, • made possible by atomic clocks. • SONET/SDH is a synchronous network using synchronous TDM multiplexing. • All clocks in the system are locked to a master clock. • This synchronization system allows entire inter-country networks to operate synchronously, • greatly reducing the amount of buffering required between elements in the network.

  10. The SONET/SDH • Both SONET and SDH can be used to encapsulate earlier digital transmission standards, • such as the PDH standard, or used directly to support either ATM or so-called Packet over SONET/SDH (POS) networking. • As such, it is inaccurate to think of SDH or SONET as communications protocols, • but rather as generic and all-purpose transport containers for moving both voice and data.

  11. Structure of SONET/SDH signals// • SONET and SDH often use different terms to describe identical features or functions. • The main difference between the two: • SONET can use either of two different basic framing units while SDH has one

  12. The basic unit of transmission// • The basic unit of framing in SDH is an STM-1 (Synchronous Transport Module level - 1), which operates at 155.52 Mbit/s. • SONET refers to this basic unit as anSTS-3c (Synchronous Transport Signal - 3, concatenated), • but it is otherwise identical in size, bit-rate, and high-level functionality. • SONET offers an additional basic unit of transmission, the STS-1 (Synchronous Transport Signal - 1), operating at 51.84 Mbit/s - exactly one third of an STM-1/STS-3c.

  13. Concatenated signals • In normal operation, an STS-n signal is made of n multiplexed STS-1 signal. • Sometimes we have a signal with a data rate higher than what an STS-1 can carry. • In this case, SONET allows us to create an STS-n signal that is not considered as n STS-1 signal; it is one STS-n signal that can not be demultiplexed into n STS-1 signal (STS-nc). • STS-3c can not be demultiplexed into three STS-1 signals. • An STS-3c can accommodate 44 ATM cells, each of 53 bytes.

  14. SONET LAYERS • The SONET standards includes four functional layer: the photonic, the section, the line and the path layer. • They corresponds to both the physical and data link layer in OSI. • The path layer • The path layer is responsible for the movement of a signal from its optical source to its optical destination. • Path layer overhead is added at this layer. • STS multiplexers provide path layer functions

  15. SONET LAYERS • The line layer • The line layer is responsible for the movement of a signal across physical line. • Line layer overhead is added to the frame at this layer. • STS multiplexers and ADM provide line layer functions

  16. SONET LAYERS • The Section layer • The line layer is responsible for the movement of a signal across physical section. • It handles framing, scrambling and error control. • Section layer overhead is added to the frame at this layer.

  17. SONET LAYERS • The Photonic layer • Corresponds to the physical layer of OSI Model. • Includes physical specification of the optical fiber channel, • SONET uses NRZ encoding with the presence of light representing one and the absence of light representing Zero.

  18. Framing • In packet or frame oriented data transmission (such as Ethernet), a frame usually consists of a header and a payload, • with the header of the frame being transmitted first, followed by the payload (and possibly a trailer). • In synchronous optical networking, this is modified slightly. The header is termed the overhead and the payload still exists, • but instead of the overhead being transmitted before the payload, it is interleaved, • with part of the overhead being transmitted, then part of the payload, then the next part of the overhead, then the next part of the payload, until the entire frame has been transmitted.

  19. Multiplexing • Three STS-1 signals may be multiplexed by time-division multiplexing to form the next level of the SONET hierarchy, the OC-3 (STS-3), running at 155.52 Mbit/s. • The multiplexing is performed by interleaving the bytes of the three STS-1 frames to form the STS-3 frame, containing 2,430 bytes and transmitted in 125 microseconds. • Higher speed circuits are formed by successively aggregating multiples of slower circuits, their speed always being immediately apparent from their designation. • For example, four STS-3 signals can be aggregated to form a 622.08 Mbit/s signal designated as OC-12 or STM-4. • OC-12 STS-12 622.080 STM-4 • OC-3 STS-3 155.520 STM-1

  20. Multiplexing • The highest rate that is commonly deployed is the OC-192 or STM-64 circuit, which operates at rate of just under 10 Gbit/s. • Speeds beyond 10 Gbit/s are technically viable and are under evaluation. • [Few vendors are offering STM-256 rates now, with speeds of nearly 40Gbit/s]. • Where fiber exhaust is a concern, multiple SONET signals can be transported over multiple wavelengths over a single fiber pair by means of Wavelength division multiplexing, • including Dense Wave Division Multiplexing (DWDM) and Coarse Wave Division Multiplexing (CWDM). DWDM circuits are the basis for all modern transatlantic cable systems and other long-haul circuits.

  21. SONET/SDH and relationship to 10 Gigabit Ethernet • Another fast growing circuit type amongst data networking equipment is 10 Gigabit Ethernet (10GbE). • This is similar in rate to OC-192/STM-64, and, in its wide area variant, encapsulates its data using a light-weight SDH/SONET frame. OC-192 STS-192 9953.280 STM-64 • However, 10 Gigabit Ethernet does not explicitly provide any interoperability at the bitstream level with other SDH/SONET systems.

  22. SONET equipment SONET regenerator • SONET Regens extend long haul routes in a way similar to most regenerators, • A regenerator is a repeater that takes a received optical signal (OC-n) (that has already traveled a long distance ), demodulates it into the corresponding electrical signal (STS-n), regenerates the electrical signal, and finally modulates the electrical signal into its corresponding OC-n signal. • Since the late 1990s, SONET regenerators have been largely replaced by Optical Amplifiers.

  23. SONET equipment STS (Synchronous Transport Signals) Multiplexer/ Demultiplexer • Mark the beginning points and endpoints of a SONET link • Provide interface between an electrical tributary network and the optical network • An STS multiplexer multiplexes signals from multiple electrical sources and creates the corresponding OC signals. • An STS demultiplexer demultiplexes an optical OC signal into corresponding electricalsignals.

  24. SONET equipment SONET Add-Drop Multiplexer (ADM) • SONET ADMs are the most common type of SONET Equipment. • SONET ADMs allows insertion and extraction of signals. • SONET ADMs can add STSs coming from different sources into a given path or can remove a desired signal from a path and redirect it without demultiplexing the entire signal. • Instead of relying on timing and bit positions, add/drop multiplexing use header info such as addresses and pointers to identify individual streams.

  25. SONET equipment Terminals • A terminal is a device that uses the services of a SONET network. • For example, in the Internet, a terminal can be a router that sends packets to another router at the other side of a SONET network. • SONET is used as a transport network to carry loads from other WANs.

  26. SONET Network Architectures • Currently, SONET (and SDH) have a limited number of architectures defined. • These architectures allow for efficient bandwidth usage as well as protection • (i.e. the ability to transmit traffic even when part of the network has failed), • and are key in understanding the almost worldwide usage of SONET and SDH for moving digital traffic. • The three main architectures are:

  27. SONET Network Architectures • Linear networks • Linear networks can be point-to-point or multipoint • Point-to-point Networks • A point-to-point network is normally made of an STS multiplexer, an STS demultiplexer and zero or more regenerators with no add/drop multiplexers. • The signal flow can be uidirectional or bidirectional.

  28. SONET Network Architectures • Multipoint networks • A multipoint network uses ADMs to allow the communications between several terminals. • An ADM removes (drops) the signal belonging to the termial connected to it and adds the signal transmitted from another terminal. • Each terminal can send data to one or more terminals. • The signal flow can be uidirectional or bidirectional.

  29. SONET Network Architectures Linear APS (Automatic Protection Switching), also known as 1+1: • To create protection against failre in linear networks, SONET defines Automatic Protection Switching (APS). • APS means protection between two ADMs or a pair of STSMux/Demux_ • Three schemes are common:

  30. SONET Network Architectures 1. ONE-PLUS-ONE APS • There are normally two lines: one working line and oneprotection line. • Both lines are active all the time. • The sending multiplexer sends the same data on both lines; the receiver multiplexer monitors the line and chooses the one with the better quality. • If one of the lines fails, the receiver selects the other line. • The sheme is inefficient because two times the bandwidth is required.

  31. SONET Network Architectures 2. ONE-to-ONE APS • There are normally two lines: one working line and one protection line. • The data are sent on the working line until it fails. • At this time the receiver , using the reverse channel, informs the sender to use the protection line instead. • The failer recovery is slower than that of the one-plus scheme but this scheme is more efficient because the protection line is used only when the working line if failed.

  32. SONET Network Architectures 3. ONE-to-Many APS • Similat to the one-to-one scheme except that there is only one protection line for many working lines. • When a failure occurs in one of the working lines, the protection line takes control until the failed line is repaired. • It is not as secure as the one-to-one scheme !

  33. SONET Network Architectures • UPSR (Unidirectional Path Switched Ring): • A type of ring network • A UPSR is a unidirectional network with two rings: one ring used as the working ring and the other as the proterction ring. • The idea is similar to the one—plus-one scheme in a linear network. • The same signal flows through both rings, one clockwise and the other counterclockwise.

  34. SONET Network Architectures • I t is called UPSR because monitoring is done at the path layer. • A node receives two copies of the electrical signal at the path layer, compares them and chooses the one with the best quality. • If a part of a ring fails, the other ring still can guarantee the continuation of data flow. • UPSR, like the one-plus-one scheme, has fast failure recovery, but it is not efficient because we need to have two rings that do the job of one!

  35. SONET Network Architectures • BLSR (Bidirectional Line Switched Ring): • A type of ring network • Communications is bidirectional, which means that we need two rings for working lines. • We also need two rings for protection lines. • The operation is similar to on-to-one APS scheme. • If a working ring in one direction between nodes fails, the receiving node can use the reverse ring to inform the upstream node in the failed direction to use the protection ring.

  36. SONET Network Architectures Combination of rings • SONET uses a combination of interconnected rings to create services in a wide area. • A SONET network may have a regional ring, several local rings and many site rings to give service to a wide area. • These rings can be UPSR. BLSR, or a combination of both.

  37. Next-generation SONET/SDH • SONET/SDH development was originally driven by the need to transport multiple PDH signals like DS1(1.544 Mbps), E1 (2.048 Mbps), DS3 (44.736 Mbps) and E3 along with other groups of multiplexed 64 kbit/s pulse-code modulated voice traffic. • The ability to transport ATM traffic was another early application. • In order to support large ATM bandwidths, the technique of concatenation was developed, whereby smaller SONET multiplexing containers (eg, STS-1) are multiplexed to build up a larger container (eg, STS-3c) to support large data-oriented pipes. • SONET/SDH is therefore able to transport both voice and data simultaneously.

  38. Next-generation SONET/SDH • One problem with traditional concatenation, however, is inflexibility. • Depending on the data and voice traffic mix that must be carried, there can be a large amount of unused bandwidth left over, due to the fixed sizes of concatenated containers. • For example, fitting a 100 Mbit/s Fast Ethernet connection inside a 155 Mbit/s STS-3c container leads to considerable waste. • Virtual Concatenation (VCAT) allows for a more arbitrary assembly of lower order multiplexing containers, building larger containers of fairly arbitrary size (e.g. 100 Mbit/s).

  39. Next-generation SONET/SDH • Virtual Concatenation increasingly leverages X.86 or Generic Framing Procedure (GFP) protocols in order to map payloads of arbitrary bandwidth into the virtually concatenated container. • Link Capacity Adjustment Scheme (LCAS) allows for dynamically changing the bandwidth via dynamic virtual concatenation, multiplexing containers based on the short-term bandwidth needs in the network. • The set of next generation SONET/SDH protocols to enable Ethernet transport is referred to as Ethernet over SONET/SDH (EoS).

More Related