230 likes | 241 Views
Units of Power and Comparison. Key ideas for wireless are coverage and performance To measure power, we can measure absolute or relative power Absolute is compared to a known scale Relative is to another signal. Pg 69. Units of Power and Comparison. Comparative units can help:
E N D
Units of Power and Comparison • Key ideas for wireless are coverage and performance • To measure power, we can measure absolute or relative power • Absolute is compared to a known scale • Relative is to another signal Pg 69
Units of Power and Comparison • Comparative units can help: • compare coverage areas for different signals • Measure gain or loss • Measure the change in power Pg 69
Watt • Basic unit of power • 1 ampere of current at 1 volt • Volts x Amps • Ability to move/push/etc Pg 70
MilliWatt (mW) • 1/1000 th of a watt • Most 802.11 equipment is measured in milliwatts • Usually 1 to 100 mw • FCC may allow up to 1 W in some cases, but it isn’t usually needed except in point to point. Pg 70
Decibel (dB) • Base unit of comparison, not of power • Represents the difference between two values • Compare the power of two transmitters • Compare the output of a transmitter and received at the receiver • From the term bel • Bell Labs • 10 to 1 ratio Pg 70
Decibel (dB) • Bels are logarithmic • Use the log10 to calculate Pg 70
Decibel (dB) • Decibels are 10 x a bel • bel=log10(P1/P2) • decibel= 10Xlog10(P1/P2) • No log math on the test! • We use decibels instead of watts as it is easier to write in many cases. Pg 70
Decibel (dB) Pg 72
dBi • Antennas are compared to isotropic radiators • The difference between the theoretical isotropic radiator and the actual antenna can be measures in decibels isotropic (dBi) • Relative measurement • Change in power relative to an antenna • Measure of antenna gain • Measured at focus point • Always a gain, not a loss • No-gain or unity gain (0 dBi) • Think antenna Gain Pg 73
dBd • A second relative measure of strength • Decibel dipole • Decibel gain relative to a dipole antenna • Can also compare to dBi • Standard dipole is 2.14 dBi • If an antenna is 3 dBd the total is additive • 2.14+3=5.14 dBi Pg 73
dBm • Absolute measurement • Decibels relative to 1 mw of power • So 100 mW= +20dBm • Can also calc from a dBm value • PmW=log-1(PdBm/10) • 1 mW is reference and 0 dBm is 1 mW Pg 74
dBm • Why use dBm? • Easier to grasp -100dBm than .0000000001 mW • Also, the 6dB rule • If you double the distance between a received and transmitter, the received signal will decrease by 6 dB. • Also, every 6dBi of gain will double the usable distance of the RF signal • Also helps when adding units • If transmitter is +20dBm and the antenna is 5 dBi, the EIRP is 25 dBm Pg 74
Inverse Square Law • The 6 dB rule is based on Isaac Newton’s inverse square law. • Change in power is equal to the square of the change in distance • If you double the distance, the power will change by (2xD)2 • FSPL = 36.6 + (20log10(f)) + (20log10(D)) • FSPL = path loss in dB • f = frequency in MHz • D = distance in miles between antennas • FSPL = 32.4 + (20log10(f)) + (20log10(D)) • FSPL = path loss in dB • f = frequency in MHz • D = distance in kilometers between antennas Pg 76
RF Math • No need for LOG on test. • Rules of 10s and 3s • Provide for approximate values • For every 3 dB of gain (relative), double the absolute power (mW). • For every 3 dB of loss (relative), halve the absolute power (mW). • For every 10 dB of gain (relative), multiply the absolute power (mW) by a factor of 10. • For every 10 dB of loss (relative), divide the absolute power (mW) by a factor of 10. Pg 77
RF Math • For every 3 dB of gain (relative), double the absolute power (mW). • For example, if your access point is configured to transmit at 100 mW and the antenna is rated for 3 dBi of passive gain, the amount of power that will radiate out of the antenna (EIRP) will be 200 mW Pg 77
RF Math • For every 3 dB of loss (relative), halve the absolute power (mW). • Conversely, if your access point is configured to transmit at 100 mW and is attached to a cable that introduces 3 dB of loss, the amount of absolute amplitude at the end of the cable will be 50 mW Pg 77
RF Math • For every 10 dB of gain (relative), multiply the absolute power (mW) by a factor of 10. • In another example, if your access point is configured to transmit at 40 mW and the antenna is rated for 10 dBi of passive gain, the amount of power that radiates out of the antenna (EIRP) will be 400 mW Pg 77
RF Math • For every 10 dB of loss (relative), divide the absolute power (mW) by a factor of 10. • Conversely, if your access point is configured to transmit at 40 mW and is attached to a cable that introduces 10 dB of loss, the amount of absolute amplitude at the end of the cable will be 4 mW. Pg 77
RF Math • dBm is a measure of power • dB is a unit of change • dB can be applied to dBm • So, if you have +10dBm and increase by 3 dB, you have +13 dBm Pg 77
Step by Step Exercise Pg 78
RF Math Summary • Log Functions • dBm =10 × log10(mW) • mW = log–1 (dBm ÷ 10) = 10(dBm ÷ 10) • Rules of 10 and 3 • 3 dB gain = mW × 2 • 3 dB loss = mW ÷ 2 • 10 dB gain = mW × 10 • 10 dB loss = mW ÷ 10 Pg 85
RF Math Summary Pg 86