170 likes | 187 Views
ECET 340 Week 1 HomeWork 1<br>ECET 340 Week 1 iLab 1<br>ECET 340 Week 2 HomeWork 2<br>ECET 340 Week 2 iLab 2<br>ECET 340 Week 3 HomeWork 3<br>ECET 340 Week 3 iLab 3<br>ECET 340 Week 4 HomeWork 4<br>ECET 340 Week 4 iLab 4<br>
E N D
ECET 340 help A Clearer path to student success/uophelp.com For more course tutorials visit www.uophelp.com
ECET 340 Entire Course (All ilabs and Homework) (Devry) For more course tutorials visit www.uophelp.com ECET 340 Week 1 iLab 1 ECET 340 Week 2 HomeWork 2 ECET 340 Week 2 iLab 2 ECET 340 Week 3 HomeWork 3 ECET 340 Week 3 iLab
ECET 340 Week 1 HomeWork 1 (Devry) For more course tutorials visit www.uophelp.com Give three examples each of internal and external peripheral devices as referenced to the HCS12 microcontroller and not an entire PC. (2 points)2. Given “the requirements of each signal’s destination must match the capabilities of the signal’s source,” name some of the electrical signal parameters that must be considered when designing an
ECET 340 Week 1 iLab 1 (Devry) For more course tutorials visit www.uophelp.com OBJECTIVES: To become familiar with Microcontroller MC9S12 parallel ports and how simple input and output devices are interfaced through them. To learn how to program I/O instructions in C language. To learn how to organize a program
ECET 340 Week 2 HomeWork 2 (Devry) For more course tutorials visit www.uophelp.com 1. Where does program control transfer to when an interrupt occurs? +2 points 2. Which one of the following Interrupts has highest priority? +2 points 3. RAM Vector table addresses $3E52 belongs to which interrupt? +2 points 4. Before exiting an ISR, the programmer
ECET 340 Week 2 iLab 2 (Devry) For more course tutorials visit www.uophelp.com ECET 340 Week 2 iLab 2
ECET 340 Week 3 HomeWork 3 (Devry) For more course tutorials visit www.uophelp.com 1. Sketch a circuit that can be used to debounce a pushbutton and explain how it works. (4 points max) 2. In Figure 7.32 on page 339 of the Huang textbook, if the row has and the columnsare , which key is pressed? (2 points max) 3. In Figure 7.32 on page 339 of the Huang textbook, explain why the 10kΩ resistors ties to VCC are
ECET 340 Week 3 iLab 3 (Devry) For more course tutorials visit www.uophelp.com SOLVED ECET 340 iLAB3 OBJECTIVES: To learn the basic operation of a keypad. To understand how to interface a keypad to a microprocessor. To learn how to program a keypad
ECET 340 Week 4 HomeWork 4 (Devry) For more course tutorials visit www.uophelp.com clock frequency is 50 kHz.2. If an 8-bit SAR has Vref = 10 V, what is the binary value for an input voltage of 7.28 V?3. What is the percent error for the binary answer found in Problem #2?
ECET 340 Week 4 iLab 4 (Devry) For more course tutorials visit www.uophelp.com . OBJECTIVES: To learn how to use A-to-D converters to digitize signals from analog input devices. To learn how to write a C language program that samples the data from an analog device, digitizes it and formats it for output on an LCD.
ECET 340 Week 5 HomeWork 5 (Devry) For more course tutorials visit www.uophelp.com . Explain, briefly, why an analog restoring filter is sometimes used at the output of a DAC.2. Given Iref = 2 mA for a DAC1408 IC, find Iout for the input 1110 11103. Find the number of discrete voltages output by a 12-bit DAC. Show work.4. Use the internet to locate
ECET 340 Week 5 iLab 5 (Devry) For more course tutorials visit www.uophelp.com Scenario/Summary This week's lab covers two areas, conversion of digital HCS12 signals to an analog format, and the use of a Serial Peripheral Interface (SPI) to transfer data, and commands between the HCS12, and the DAC peripheral.
ECET 340 Week 6 HomeWork 6 (Devry) For more course tutorials visit www.uophelp.com What are the four main functions of the HC12 Timer unit?2. Two input capture events occur at counts 0x1037 and 0xFF20 of the free-running counter. How many counts (in decimal) have transpired between these two events?
ECET 340 Week 6 iLab 6 (Devry) For more course tutorials visit www.uophelp.com ECET 340 Week 6 iLab 6
ECET 340 Week 7 HomeWork 7 For more course tutorials visit www.uophelp.com 1. The movable part of the solenoid is the: +2 points 2. Why is the 6N139 optoisolator used in the interfaces to devices such as large motors? +2 points 3. Calculate the number of steps per revolution for a stepper motor with a step angle of 7.5°. +2 points 4. How is stepper motor
ECET 340 Week 7 iLab 7 (Devry) For more course tutorials visit www.uophelp.com ECET 340 Week 7 iLab 7
ECET 340 help A Clearer path to student success/uophelp.com For more course tutorials visit www.uophelp.com