1 / 29

Maximizing Processor Efficiency with Interrupts in 8085A Microprocessor

Understand interrupt input types, sequence of actions, interrupt structure, sensitivity, acknowledge process, and priority structure in the 8085A microprocessor for efficient system performance.

burkeb
Download Presentation

Maximizing Processor Efficiency with Interrupts in 8085A Microprocessor

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Interrupts Disclaimer: All diagrams and figures in this presentation are scanned from the book “Microprocessors and Programmed Logic” authored by Kenneth L.Short and they are reproduced for educational purposes only.

  2. Interrupts • Interrupts increase processor system efficiency by letting I/O device request CPU time only when that device needs immediate attention. • An interrupt is a subroutine call initialized by external hardware.

  3. Interrupt Request • The request is asynchronous  it may occur at any point in a program’s execution.

  4. Interrupt Input Types • Nonmaskable interrupt input • The MPU is interrupted when a logic signal is applied to this type of input. • Maskable interrupt input • The MPU is interrupted ONLY if that particular input is enabled. • It is enabled or disabled under program control. • If disabled, an interrupt signal is ignored by the MPU.

  5. Maskable & Nonmaskable INT

  6. Sequence of Actions

  7. Sequence of Actions • The processing of the current instruction is completed. • An interrupt machine cycle is executed during which the PC is saved and control is transferred to an appropriate memory location.

  8. Sequence of Actions • The state of the MPU is saved. • If more than one I/O device is associated with the location transferred to, the highest priority device requesting an interrupt is identified.

  9. Sequence of Actions • A subroutine is executed which services the interrupt I/O device. • The saved state of the microprocessor is restored. • Control is returned to the instruction that follows the interrupted instruction.

  10. 8085A Interrupt Structure • There are 5 interrupt inputs: • TRAP (nonmaskable) • RST7.5 • RST6.5 • RST5.5 • INTR

  11. 8085A Interrupt Structure • When the 8085A is reset: • Its internal interrupt enable flip-flop (INTE FF) is reset. • This disables ALL the maskable interrupts. • So, the MPU only responds to TRAP. • Maskable interrupts must be enabled under program control. • Let’s prove and find out which address the TRAP would go?

  12. RST7.5, RST6.5, RST5.5 • Two program steps are required to enable these interrupts: • Setting the interrupt masks • Enabling the interrupts • SIM (set interrupt mask) is the instruction to mask each interrupt independently.

  13. 8085A Interrupt Structure • We can gather the status of maskable interrupt and interrupt enable/disable from the instruction RIM (Read Interrupt Mask)

  14. INTR • Although INTR is a maskable interrupt • it does NOT need SIM to get enabled. • Just instruction EI is enough.

  15. Interrupt Inputs’ Sensitivity • Level sensitive • RST6.5 and RST 5.5 are high level sensitive • The signal at these pins must be maintained until the interrupt is acknowledged • External interrupt request flip-flops are required

  16. Interrupt Inputs’ Sensitivity • Edge sensitive • RST7.5 (Rising edge sensitive) • Only a pulse is required to set the interrupt request  this request is remembered until the 8085A responds to the interrupt or until the request is reset by the SIM instruction or a /RESET IN signal. • The interrupt request flip-flops for RST7.5 is internal to the microprocessor

  17. Interrupt Inputs’ Sensitivity • Both edge and level sensitive • TRAP • Must make a low-to-high transition and remain high to be acknowledged. • After acknowledgement, it is NOT recognized again until it goes low, then high again and remains high. • To avoid false triggering due to noise/logic glitches.

  18. Remember This?

  19. BUS IDLE (BI) Machine Cycle • TRAP, RST5.5, RST6.5, and RST7.5 RST (internal) ((SP) – 1)  (PCH) ((SP) – 2)  (PCL) (SP)  (SP) – 2 (PC)  restart address

  20. INTERRUPT ACKNOWLEDGE (INA) Machine Cycle • INTR ( 0 =< n =< 7 ) RST n ((SP) – 1)  (PCH) ((SP) – 2)  (PCL) (SP)  (SP) – 2 (PC)  8*n • External logic must generate interrupt vector as 11NNN111 at the data bus

  21. Priority Interrupt Structures • 8085A have an internally established, fixed, multilevel priority structure. • From highest to lowest: • TRAP • Usually reserved to handle catastrophies such as power failures. • RST7.5 • RST6.5 • RST5.5 • INTR

More Related