1 / 26

EE121 John Wakerly Lecture #15

EE121 John Wakerly Lecture #15. CPLDs FPGAs. CPLDs vs. FPGAs. CPLD architecture Small number of largish PLDs (e.g., “36V18”) on a single chip Programmable interconnect between PLDs. FPGA architecture Much larger number of smaller programmable logic blocks.

burrow
Download Presentation

EE121 John Wakerly Lecture #15

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. EE121 John Wakerly Lecture #15 CPLDs FPGAs

  2. CPLDs vs. FPGAs • CPLD architecture • Small number of largish PLDs (e.g., “36V18”) on a single chip • Programmable interconnect between PLDs

  3. FPGAarchitecture • Much larger number of smaller programmable logic blocks. • Embedded in a sea of lots and lots of programmable interconnect.

  4. How to expand PLD architecture? • Increase # of inputs and outputs in a conventional PLD? • E.g., 16V8 --> 20V8 --> 22V10. • Why not --> 32V16 --> 128V64 ? • Problems: • n times the number of inputs and outputs requires n2 as much chip area -- too costly • logic gets slower as number of inputs to AND array increases • Solution: multiple PLDs with a relatively small programmable interconnect. • Less general than a single large PLD, but can use software “fitter” to partition into smaller PLD blocks.

  5. CPLD families • Identical individual PLD blocks (Xilinx “FBs”) replicated in different family members. • Different number of PLD blocks • Different number of I/O pins • Many CPLDs have fewer I/O pins than macrocells • “Buried” Macrocells -- provide needed logic terms internally but these outputs are not connected externally. • IC package size dictates # of I/O pins but not the total # of macrocells. • Typical CPLD families have devices with differing resources in the same IC package.

  6. Xilinx CPLDs • Notice overlap in resource availability in a particular package.

  7. 72 ==>XC9572 Xilinx 9500-family CPLD architecture

  8. 9500-family function blocks (FBs) • 18 macrocells per FB • 36 inputs per FB (partitioning challenge, but also reason for relatively compact size of FBs) • Macrocell outputs can go to I/O cells or back into switch matrix to be routed to this or other FBs.

  9. 9500-series macrocell (18 per FB) Set control Programmable inversion or XOR product term Up to 5 product terms Global clock or product-term clock Reset control OE control

  10. programmable steeringelements 9500-series product-term allocator Share terms from above and below

  11. 9500-series I/O block

  12. Switch matrix for XC95108 • Could be anything from a limited set of multiplexers to a full crossbar. • Multiplexer -- small, fast, but difficult fitting • Crossbar -- easy fitting but large and slow

  13. FPGAs • Historically, FPGA architectures and companies began around the same time as CPLDs • FPGAs are closer to “programmable ASICs” -- large emphasis on interconnection routing • Timing is difficult to predict -- multiple hops vs. the fixed delay of a CPLD’s switch matrix. • But more “scalable” to large sizes. • FPGA programmable logic blocks have only a few inputs and 1 or 2 flip-flops, but there are a lot more of them compared to the number of macrocells in a CPLD.

  14. General FPGA chip architecture a.k.a. CLB --“configurable logicblock”

  15. Xilinx 4000-series FPGAs

  16. FPGA specsmanship • Two flip-flops per CLB, plus two per I/O cell. • 25 “gates” per CLB if used for logic. • 32 bits of RAM per CLB if not used for logic. • All of this is valid only if your design has a “perfect fit”.

  17. Configurable Logic Block (CLB)

  18. CLB function generators (F, G, H) • Use RAM to store a truth table • F, G: 4 inputs, 16 bits of RAM each • H: 3 inputs, 8 bits of RAM • RAM is loaded from an external PROM at system initialization. • Broad capability using F, G, and H: • Any 2 funcs of 4 vars, plus a func of 3 vars • Any func of 5 vars • Any func of 4 vars, plus some funcs of 6 vars • Some funcs of 9 vars, including parity and 4-bit cascadable equality checking

  19. CLB input and output connections -- buried in the sea of interconnect

  20. Detail connectionscontrolled byRAM bits

  21. programmable switch element turning the corner, etc. Programmable Switch Matrix

  22. The fitter’s job • Partition logic functions into CLBs • Arrange the CLBs • Interconnect the CLBs • Minimize the number of CLBs used • Minimize the size and delay of interconnect used • Work with constraints • “Locked” I/O pins • Critical-path delays • Setup and hold times of storage elements

  23. Oh, by the way -- I/O blocks

  24. Problems common to CPLDs and FPGAs • Pin locking • Small changes, and certainly large ones, can cause the fitter to pick a different allocation of I/O blocks and pinout. • Locking too early may make the resulting circuit slower or not fit at all. • Running out of resources • Design may “blow up” if it doesn’t all fit on a single device. • On-chip interconnect resources are much richer than off-chip; e.g., barrel-shifter example. • Larger devices are exponentially more expensive.

  25. Midterm Solutions Discussion

  26. Next Time • Synchronous design methodology • Metastability

More Related