1 / 19

Presented By Lorenzo Andrioli

TFAWS Paper Session. Thermal Analysis in Support to Thermal Protection System Seals and Interface Design of IXV Lorenzo Andrioli, Massimo Antonacci Thales Alenia Space – Turin, Italy Alessandro Mannarelli SSE Sofiter System Engineering – Turin, Italy. Presented By Lorenzo Andrioli.

cicero
Download Presentation

Presented By Lorenzo Andrioli

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. TFAWS Paper Session Thermal Analysis in Support to Thermal Protection System Seals and Interface Design of IXVLorenzo Andrioli, Massimo AntonacciThales Alenia Space – Turin, ItalyAlessandro MannarelliSSE Sofiter System Engineering – Turin, Italy Presented ByLorenzo Andrioli Thermal & Fluids Analysis WorkshopTFAWS 2011August 15-19, 2011 NASA Langley Research CenterNewport News, VA

  2. Outline • Introduction • Analysis Approach • Interfaces (I/F) Thermal Mathematical Models (TMMs) general description • Thermal network basic concept • Environment simulation • Analysis work logic • Model example • New approach for Thermal Protection System (TPS) thermal analysis • Summary & Conclusions TFAWS 2011 – August 15-19, 2011

  3. Introduction The IXV (IntermediateeXperimentalVehicle) • An atmospheric re-entry demonstrator which will perform a suborbital flight and will re-enter in the atmosphere. • To be launched by the ESA/Vega from the Centre Spatial Guyanais (CSG) • It will experience the typical Low Earth Orbit re-entry thermal loads. TFAWS 2011 – August 15-19, 2011 3

  4. Introduction Main objective: To develop an analytical approach to be implemented for I/F design of IXV. Model characteristics changes operated by means of: • algorithms • configurations To properly simulate behaviour of items characterized by different: • thermal properties • thermo-mechanical properties • permeability Leading to different temperature requirement limits. TFAWS 2011 – August 15-19, 2011 4

  5. Introduction Interfaces (I/F) External critical regions in which environmental agents can find a preferential way to dangerously affect internal environment and items. Design requirements: • to limit sneak flow and act as thermal barriers (proper sealing); • to limit discontinuities (steps, gaps, and bowing) in the vehicle Outer Mould Line; • to allow depressurization and repressurization of IXV and TPS&H/S Assemblies. TFAWS 2011 – August 15-19, 2011 5

  6. Introduction Different types of I/Fs to be designed: • among different-type Thermal Protection Systems: • nose-to-windward • nose-to-leeward • leeward-to-windward • windward-to-hinge • hinge-to-rear • hinge-to-leeward • between TPSs and other subsystems: • floatation system ejectable panels insulation • venting hole • protection insulation over antennas • bridle channels insulation • protection insulation on umbilical mechanisms TFAWS 2011 – August 15-19, 2011 6

  7. Analysis Approach Modelingcriterion • ESATAN Thermal Lumped Parameter (TLP) solver • Technique resembles System Thermal Mathematical Model (TMM) one improving temperature mapping capabilities • highly customizable 2D mesh models and one 3D axisymmetric model • depending on the I/F type, a fluid leak (sneak flow) through sealing materials is simulated TFAWS 2011 – August 15-19, 2011 7

  8. I/F TMMs general description Thermal network basic concept • Thermal network organized in node blocks linked together to establish a geometrical hierarchy → propagation of changes by acting upon relevant parameters (e.g. modification of items sizing, material properties, etc.) • Node blocks wrapped into arithmetical nodes→ spreading effect of surface heat exchanges implicitly solved (reliable evaluation of I/F temperatures) TFAWS 2011 – August 15-19, 2011 8

  9. I/F TMMs general description Environment simulation • Internal environment: radiative and convective equivalent conductors (representative nodes defined on the basis of System TMM) • External environment: radiative conductors and heat fluxes (ATDB, max heat load trajectory) or input from dedicated thermo-ablative software • Sneak flow: modelled by means of a heat contribution calculated as: TFAWS 2011 – August 15-19, 2011 9

  10. I/F TMMs general description Air mass flow: calculated with Darcy law 1D formulation k permeability of the seal mair kinematic viscosity rair density thspatial term describing the flow path (seal thickness) ppressure Aflow area (gap× slot width) Sneak flow into non-passing through slots: air filling the gap is considered as stagnating (really thin and deep slots, highly conservative boundary layer temperature) TFAWS 2011 – August 15-19, 2011 10

  11. I/F TMMs general description • Air flow through venting hole: equivalent thermal conductor (h × A) linking duct with a inflow boundary node kairair conductivity rbushduct internal radius NuNusselt number From Petukhov-Gnielinski semi-empiric correlation: TFAWS 2011 – August 15-19, 2011 11

  12. I/F TMMs general description Analysis work logic TFAWS 2011 – August 15-19, 2011 12

  13. I/F TMMs general description Model example: typical TPS-to-TPS junction I/F TFAWS 2011 – August 15-19, 2011 13

  14. Analysis results and their application Local vs System TMMs DT are applied to overall vehicle temperature maps all along the I/Fs envelope at C/S and TPS level. Temperature maps are used as an input for System Thermo-elastic analyses→ overall steps and gaps requirements verification TFAWS 2011 – August 15-19, 2011 14

  15. New approach for TPS thermal analysis Current approach modeling (ESATAN) flaws: • ESATAN-TMS GUI is in early development phase→ code is usually written down by hand • Manual debugging and subroutine generation is the rule→ coding is more error-prone than a robust front-end approach • CAD interfacing tools are under development→ geometry is user discretized and modeled, usually in scripting form with graphic visualization • Data exchange is manually managed by means of properly written routines→ a coding endeavor is required TFAWS 2011 – August 15-19, 2011 15

  16. New approach for TPS thermal analysis Solution: switching to an hybrid approach tool. • Bi-directional from/to CAD geometry interfacing, with direct user intervention for simplification purposes • Finite element based model mesh generation • Possibility to chose between a Finite Element Method (FEM) or a TLP solution • Possibility to chose between FEM or TLP like postprocessing (temperatures interpolated over the node vs isothermal nodes) TFAWS 2011 – August 15-19, 2011 16

  17. New approach for TPS thermal analysis FEM-TLP hybrid workflow in NX environment An example of hybrid approach workflow applied to a preliminary TPS-to-TPS I/F analysis. TFAWS 2011 – August 15-19, 2011 17

  18. Summary & Conclusions The presented modelling approach has been developed in the frame of IXV programme resulting into a key feature of the I/F design assessment at System level. The adopted work logic resulted in an effective approach to: • Achieve the required detail level for I/Fs design justification • Reduce development times and iterations between the different disciplines involved • Minimize and enhance data exchange cycles among several analysis tools TFAWS 2011 – August 15-19, 2011 18

  19. Summary & Conclusions Improvements based on hybrid FEM/TLP analysis are being implemented to: • Boost up detail level for I/Fs design refinement • Further reduce development and coding endeavor (minimizing modeling mistakes) • Enhance data exchange among several CAD/analysis suites TFAWS 2011 – August 15-19, 2011 19

More Related