1 / 13

SAM9260-EK WinCE DEMO

SAM9260-EK WinCE DEMO. AT91 SAM9 Product Group. Version 1.0 October 2006. SAM9260-EK Boot Solutions. Jumper J7 (Boot Mode Select) allows to select the Boot Mode of the AT91SAM9260-EK J7 Opened, the AT91SAM9260 boots from the on-chip Boot ROM

cosima
Download Presentation

SAM9260-EK WinCE DEMO

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. SAM9260-EKWinCE DEMO AT91 SAM9 Product Group. Version 1.0 October 2006

  2. SAM9260-EK Boot Solutions • Jumper J7 (Boot Mode Select) allows to select the Boot Mode of the AT91SAM9260-EK • J7 Opened, the AT91SAM9260 boots from the on-chip Boot ROM • The on-chip Boot ROM Memory integrates different programs permitting download and/or upload into the different memories of the product • First, it initializes the DBGU and the USB Device Port. • Then the DataFlash Boot program is executed. It looks for a sequence of eight valid ARM exception vectors in a DataFlash connected to the SPI. If a valid sequence is found, code is downloaded into the internal SRAM. This is followed by a remap and a jump to the first address of the SRAM. • Then the NANDFlash Boot program is executed. It looks for a sequence of eight valid ARM exception vectors in a NANDFlash. If a valid sequence is found, code is downloaded into the internal SRAM. This is followed by a remap and a jump to the first address of the SRAM. • If no valid ARM vector sequence is found, SAMBA™ Boot is then executed. It waits for transactions either on the USB device, or on the DBGU serial port. Then, user can use SAM-BA GUI to download binary file into the different memories of the product. • J7 Closed, the AT91SAM9260 boots from the off-chip memory connected to NCS0 (No memory is connected on the EK by default)

  3. SAM9260-EK WinCE Demo • Software requirements • Demo WinCE file including: • Binary Files: BootRam.bin, EBOOT.nb0 & NK.nb0 • AT91ISP V1.4(or higher) GUI Application installed on your computer • Hardware requirements • SAM9260-EK Evaluation Kit • Serial Cross Cable (Female-Female) • USB Device Cable • Ethernet Cable

  4. SAM9260-EK SAM-BA Boot • Install AT91ISP v1.4 and reboot your computer • Reset the board • Connect the USB Device Interface (J19) to your PC using the USB Device Cable • Start SAMBA GUI Application • Select theSAM9260-EKand chooseUSB Connection

  5. Download BootRAM.bin in DataFlash with SAM-BA • Select DataFlash AT45DB/DCB tab • Choose Init & Select AT45DCB Dataflash Card on CS1 in scripts rolling menu and press Execute • Choose Send BOOT File in scripts rolling menu and press Execute • Choose file named BootRam.bin and press Open. 1°- Init & Select AT45DCB Dataflash Card on CS1 2°- Send BOOT File

  6. Download EBOOT.nb0 in DataFlash with SAM-BA • Press onSend File Name Browsebutton • Enter “0x4000” inInternal Addresstext field • Choose EBOOT.nb0and pressOpen • PressSend Filebutton EBOOT.nb0 Dataflash internal address 0x5000

  7. Download WinCE Demo (NK.nb0) in NandFlash with SAM-BA • Select NandFlash tab • Choose Init NandFlash in scripts rolling menu and press Execute • Press onSend File Name Browsebutton • Choose file named NK.nb0 and press Open. • PressSend Filebutton (this will take a few moment): WinCE has been stored in NandFlash • Close SAMBA, remove USB cable 2°- Send NK.nb0 1°- Init NandFlash

  8. Configure WinCE Boot: EBOOT • Connect the Serial Debug Port (J17) to your PC using the Serial Cross Cable • Start an hyperterminal session on your PC with settings: • 115200 8-N-1 • Reset the board • Press “Space” key when the message“Initiating image launch in x seconds”is displayed to stop booting, the following Menu is then displayed • Ethernet Boot Loader Configuration:0) MAC address: 02:03:04:05:06:071) IP address: 192.168.100.1282) Subnet mask: 255.255.255.03) Boot delay: 5 seconds4) DHCP: (Enabled)5) Reset to factory default configuration6) Download new image at startup7) Download image to SDRAM8) Frequency settings (core at 200, bus divider 2)A) test RTC:D) Download image nowL) Launch existing flash resident image nowN) Nand Flash menu

  9. Configure WinCE Boot: EBOOT • Select option “1” and enter your own IP address and Subnet Mask The board must be on the same subnet as your PC • The following menu is then displayed: • Ethernet Boot Loader Configuration:0) MAC address: 02:03:04:05:06:07 1) IP address: xxx.yyy.zzz.ttt2) Subnet mask: 255.255.254.03) Boot delay: 5 seconds4) DHCP: (Enabled)5) Reset to factory default configuration6) Download new image at startup7) Download image to SDRAM8) Frequency settings (core at 200, bus divider 2) A) test RTC:D) Download image nowL) Launch existing flash resident image nowN) Nand Flash menu

  10. Configure WinCE Boot: EBOOT • Select option “4” • The following menu is then displayed: • Ethernet Boot Loader Configuration:0) MAC address: 02:03:04:05:06:07 1) IP address: xxx.yyy.zzz.ttt 2) Subnet mask: 255.255.254.03) Boot delay: 5 seconds4) DHCP: (Disabled)5) Reset to factory default configuration6) Download new image at startup7) Download image to SDRAM8) Frequency settings (core at 200, bus divider 2) A) test RTC:D) Download image nowL) Launch existing flash resident image nowN) Nand Flash menu

  11. Configure WinCE Boot: EBOOT • Select option “6” • The following menu is then displayed: • Ethernet Boot Loader Configuration:0) MAC address: 02:03:04:05:06:07 1) IP address: xxx.yyy.zzz.ttt 2) Subnet mask: 255.255.254.03) Boot delay: 5 seconds4) DHCP: (Disabled)5) Reset to factory default configuration6) Launch existing flash resident image at startup7) Download image to SDRAM8) Frequency settings (core at 200, bus divider 2) A) test RTC:D) Download image nowL) Launch existing flash resident image nowN) Nand Flash menu

  12. Configure WinCE Boot: EBOOT • In hyperterminal menu • Select option N, “Nand Flash menu”: • The following menu is then displayed: • Nand Flash Menu :1) Erase all sectors2) Enter manually the image parameters3) Quit... • Select option “2” and set the following settings: • Physical Start Address : (0x80059000) : 0x80067000(Press Return)Starting ip : (0x8005a000) : 0x80068000(Press Return)Total ROM size : (0x75144c) : 0x8b3bfc(Press Return) • Reset the board and wait for a few moment

  13. Browsing the board with your PC • Plug the Ethernet Cable in Ethernet Interface (J14) and on your PC. • Start your favorite browser and enter the board URL : http://xxx.yyy.zzz.ttt • You can browse the demo web site thanks to the webserver. • Your own web site can be added on a USB key. For that : • Type telnet xxx.yyy.zzz.ttt in a windows on your PC. • In this telnet session type WebServerSettings USB \USBDisk\YourSite • enter the board URL : http://xxx.yyy.zzz.ttt/USB/ • You can browse your web site.

More Related