1 / 96

Hi-Scan Pro Application

Hi-Scan Pro Application. Hi-Scan Pro Application. CONTENTS. 1. Kia Vehicle Diagnosis 2. Vehicle Scope meter 3. System Setup 4. Optional Items 5. PC-Scan. 1.1 DIAGNOSIS TROUBLE CODE 1.2 FREEZE FRAME DATA 1.3 CURRENT DATA 1.4 MONITERING TEST RESULT 1.5 EVAP. LEAKAGE TEST

dieter-herring
Download Presentation

Hi-Scan Pro Application

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Hi-Scan Pro Application

  2. Hi-Scan Pro Application CONTENTS 1. Kia Vehicle Diagnosis 2. Vehicle Scope meter 3. System Setup 4. Optional Items 5. PC-Scan

  3. 1.1 DIAGNOSIS TROUBLE CODE 1.2 FREEZE FRAME DATA 1.3 CURRENT DATA 1.4 MONITERING TEST RESULT 1.5 EVAP. LEAKAGE TEST 1.6 FLIGHT RECORD 1.7 DUAL DISPLAY 1.8 SIMU-SCAN Hi-Scan Pro Application 1. Kia Vehicle Diagnosis

  4. Hi-Scan Pro Application ENTER ENTER ENTER 1.1 DIAGNOSIS TROUBLE CODE ( 1/5) To get started. Following procedures are within KIA VEHICLE DIAGNOSIS mode • On the Hi-Scan Pro keyboard; • Press “ON/OFF” button to turn on the Hi-Scan Pro • Keep on press “Enter” button until Initial screen come up. • Make sure DLC cable is properly connected. • FIRST : SELECT VEHICLE DIAGNOSIS • SECOND : SELECT VEHICLE • THIRD : SELECT SYSTEM • FOURTH : SELECT VEHICLE YEAR

  5. Hi-Scan Pro Application ENTER ENTER 1.1 DIAGNOSIS TROUBLE CODE (2/5) To view Diagnostic Trouble code. • After Selecting the vehicle model year, go through the Diagnostic Trouble Code and Current data to diagnose the vehicle. • If ECM or communication WIRE has problem, Hi-Scan Pro cannot communicate with vehicle and display the message as shown in picture. OR

  6. Hi-Scan Pro Application ENTER 1.1 DIAGNOSIS TROUBLE CODE (3/5) To check Diagnostic Trouble Code ENTER • If ECM has no trouble code with engine system, Hi-Scan Pro display on the screen “NO TROUBLE CODE” • If ECM has trouble code with engine system, Hi-Scan Pro display “TROBLE CODE WITH ITEM” OR

  7. Hi-Scan Pro Application 1.1 DIAGNOSIS TROUBLE CODE (4/5) To get information about DTC and delete DTC • HELP : Basic & Major information to help understand each trouble code and item • ERAS : Erase Trouble Code(Follow the instruction carefully) F2 ERAS F1 HELP

  8. Hi-Scan Pro Application F3 FRZE F6PART 1.1 DIAGNOSIS TROUBLE CODE (5/5) To check the data of sensor with DTC when DTC is occurred. • FREZ : Display the data of items with DTC at the situation when trouble is occurred. • Hi - Scan display “FRZE” data only when ECM support this function. • PART : Precise diagnosis for each sensor(Oscilloscope)

  9. Hi-Scan Pro Application Previous menu ENTER ENTER ENTER ENTER • FREZ : Display the data of items with DTC at the situation when trouble is occurred. • Hi - Scan display “FREZ” data only when ECM support this function. ENTER 1.2 FREEZE FRAME DATA To check the data of sensor with DTC when DTC is occurred. Press “ENTER” with the cursor on “02. FREEZE FRAME DATA” in “1. KIA VEHICLE DIAGNOSIS” mode. In this case, connect with vehicle via DLC cable.

  10. Hi-Scan Pro Application ENTER 1.3 CURRENT DATA (1/2) To view the sensor and actuator data. Select “CURRENT DATA” in “KIA VEHICLE DIAGNOSIS” mode. In this case, connect with vehicle via DLC cable. • FIX : Fix current data and display on the top of the screen • PART : Precise diagnosis for sensor with inverted letters(Oscilloscope) • FULL : Display full 22 items’ data F2 PART F3 FULL F1 FIX

  11. Hi-Scan Pro Application F4 HELP F5 GRPH 1.3 CURRENT DATA (2/2) To view the sensor and actuator data. • HELP : Provide reference data • GRPH : Waveform graph display • RCRD : Record sensor data F6 RCRD

  12. Hi-Scan Pro Application 1.3 CURRENT DATA - PART To analyze part precisely. Previous menu ENTER ENTER ENTER ENTER ENTER F2 PART • Connect a probe to “CH A” of Hi-Scan Pro • Go through the appropriate mode and press “ENTER” on “03. CURRENT DATA”. • Press “F2” button to operate “PART” function. • PART : Place a box, in which letters are inverted, and press “PART” for precise part analysis. • Connect a Test Probe to Channel A of Hi-Scan Pro. • Oscilloscope mode begin as shown in the picture.

  13. Hi-Scan Pro Application 1.3 CURRENT DATA - GRAPH To view the pattern of sensor or actuator data Previous menu ENTER ENTER ENTER ENTER ENTER F1 FIX F5 GRPH On a “CURRENT DATA” mode, press “F1” to fix the items and “F5” to view the graph. • FIX : Select the sensors to view “GRAPH” • GRPH : Waveform graph display • FIX : Select the sensors to fix at the top of the screen. You can change the sensor by pressing FIX button again. You can scroll up and down without moving fixed sensor.

  14. Hi-Scan Pro Application 1.3 CURRENT DATA - RECORD To record the sensor or actuator data. Previous menu ENTER ENTER ENTER ENTER ENTER F6 RCRD On a “CURRENT DATA” mode, press “F6” to record a data. • RCRD : Move to “RECORD” mode, in which select trigger type. • AUTO TRIGGER(ANY DTC) : Triggers with any DTC. • AUTO TRIGGER(SINGLE DTC) : Trigger with single user specified DTC. • MANUAL TRIGGER : User trigger the data recording. • FLIGHT RECORD DATA REVIEW : Fetch recorded data.

  15. Hi-Scan Pro Application 1.3 CURRENT DATA – AUTO TRIGGER (ANY DTC) (1/2) Record a data using AUTO TRIGGER. Previous menu ENTER ENTER ENTER ENTER ENTER ENTER ENTER AUTO TRIGGER (ANY DTC) ENTER After “TRIGGER TYPE” is chosen, Select memory location using “▲””▼” buttons and press enter. TYPE ID • ENTER : Select the memory location then press “ENTER” to type memory ID. • Type “CAR ID”. • ENTER : Go to “DATA RECORD” select mode. Select the “DATA RECORD” type and press “ENTER”.

  16. Hi-Scan Pro Application 1.3 CURRENT DATA – AUTO TRIGGER (ANY DTC) (2/2) Choose items to record: all or custom. “01” ENTER • USER SELECT DATA RECORD. : Record user defined sensor data. • FIX : Select sensors to record in ‘USER SELECT DATA RECORD”. • ENTER : Start “RECORDING” • ESC :”STOP” recording “02” ENTER • ALL DATA RECORD : Record all sensor data

  17. Hi-Scan Pro Application 1.3 CURRENT DATA – AUTO TRIGGER (SINGLE DTC) Enter specific DTC which will be used as trigger. ENTER • AUTO TRIGGER(SINGLE DTC) • : Record user defined single DTC. • Type specific “DTC CODE” and press “ENTER”. • Rest of procedures are same as “AUTO TRIGGER (ANY DTC)” Type DTC CODE and press ENTER

  18. Hi-Scan Pro Application 1.3 CURRENT DATA – MANUAL TRIGGER (1/2) User triggers the record data. ENTER ENTER ENTER • MANUAL TRIGGER : Place a mark on a recorded data where “ENTER” button is pressed while recording. This mark is displayed as vertical line in “GRAPH” mode. • Next procedures are same as “AUTO TRIGGER”. • Select “DATA RECORD” type. TYPE ID

  19. Hi-Scan Pro Application 1.3 CURRENT DATA – MANUAL TRIGGER (2/2) Choose items to record: all or custom. “01” ENTER • USER SELECT DATA RECORD. : Record user defined sensor data. • FIX : Select sensors to record and press “F1”. • ENTER : Start “RECORDING”. • ENTER : Start “TRIGGERING”. • ESC :”STOP” recording. “02” ENTER • ALL DATA RECORD : Record all sensor data • ENTER : Place a mark on a data where “ ENTER” is pressed while recording.

  20. Hi-Scan Pro Application 1.3 CURRENT DATA –FLIGHT RECORD VIEW (1/2) Review recorded data ENTER • FLIGHT RECORD DATA REVIEW : Review recorded data. • Select the memory location, then press “ENTER”. • Press “ENTER” to review recorded data. Select the memory location and press “ENTER”

  21. Hi-Scan Pro Application 1.3 CURRENT DATA –FLIGHT RECORD VIEW (2/2) Select review type. ENTER • GRAP : Covert the “LIST” screen into “GRAPH”. • LIST : Covert the “GRAPH” screen into “LIST”. • HOME : Place the triggered position, displayed as vertical line, at the middle of the screen. • FIX : You can scroll up and down without moving fixed item. If you press “FIX” again, you can change the item to fix. F1 “GRAP” F1 “LIST”

  22. Hi-Scan Pro Application 1.4 MONITORING RESULTS To monitor emission related operations ENTER ENTER ENTER ENTER Previous menu Select “MONITORING TEST RESULT” in “KIA VEHICLE DIAGNOSIS” mode. In this case, connect with vehicle via DLC cable. • MONITORING TEST RESULT : This function provides 3 tests, which are 1) READINESS TEST 2) HO2S MONITERING TEST 3) OBD2 MONITERING TEST ENTER

  23. Hi-Scan Pro Application 1.4 MONITORING RESULTS – READNESS TEST To monitor emission related operations ENTER ENTER • READINESS TEST : Displays vehicle’s on-board monitoring. : Emission-related operations are monitored. • Test result accurately reflect vehicles’ condition of emission related components.

  24. Hi-Scan Pro Application 1.4 MONITORING RESULTS – HO2S MONITORING TEST To monitor Oxygen sensor test result. ENTER ENTER ENTER • HO2S MONITERING TEST : display the results of the Heated Oxygen Sensor testing performed by the ECM • Hi – Scan pro also displays test result by converting ECM data. • The test result is valid only after ECM’s H2OS monitoring is finished.

  25. Hi-Scan Pro Application 1.4 MONITORING RESULTS – OBD2 MONITORING TEST To monitor OBD2 test. ENTER ENTER ENTER • OBD2 MONITORING TEST : User can access to the on-board diagnostic monitoring test result of specific component /system that are not continuously monitored. • List of OBD monitor applicable for RIO - Three-way catalyst converter. - HO2S monitoring. - EVAP. EM monitoring. -Thermostat monitoring. - HO2S heater(B1S1). - HO2S heater(B1S2). - ECT Plausibility.

  26. Hi-Scan Pro Application 1.5 EVAP. LEAKAGE TEST (1/4) Previous menu To inspect EVAP leakage. ENTER ENTER ENTER ENTER ENTER F6 HELP • EVAP. LEAK TEST MODE : The EVAP. Leakage Test is based on the diagnosis module for tank leakage detection uses an electrically driven vane pump. • Please follow the Hi-Scan Pro EVAP. LEAKAGE TEST process like picture. Select “EVAP LEAKAGE TEST” in “KAI VEHICLE DIAGNOSIS” mode. In this case, connect with vehicle via DLC cable. DOWN

  27. Hi-Scan Pro Application 1.5 EVAP. LEAKAGE TEST (2/4) To inspect EVAP leakage. ENTER • NORMAL CONDITION OF EVAP. SYS :If evap. Sys of vehicle had being normal, Hi-Scan Pro display O.K of the test results.

  28. Hi-Scan Pro Application 1.5 EVAP. LEAKAGE TEST (3/4) To inspect EVAP leakage. ENTER ENTER DOWN • ABNORMAL CONDITION OF EVAP. SYS :If evap. Sys of vehicle had being abnormal, Hi-Scan Pro display ACTIVATION IS NOT POSSIIBLE. • Please check the vehicle condition according to Hi-Scan Pro process.

  29. Hi-Scan Pro Application 1.5 EVAP. LEAKAGE TEST (4/4) To inspect EVAP leakage. ENTER • ABNORMAL CONDITION OF EVAP. SYS:If you retry EVAP. Leakage test with-in 5 minutes had finished EVAP. Leakage test, Hi-Scan Pro will display NOT NECESSRRY.

  30. Hi-Scan Pro Application 1.6 FLIGHT RECORD – AUTO TRIGGER (1/2) To record sensor or actuator data. ENTER ENTER ENTER ENTER ENTER AUTO TRIGGER (ANY DTC) Previous menu Select “FLIGHT RECORD” in “KIA VEHICLE DIAGNOSIS” mode. In this case, connect with vehicle with DLC cable. ENTER TYPE ID • ENTER : Select the memory location then press “ENTER” to type memory ID. • Type “CAR ID”. • ENTER : Go to “DATA RECORD” select mode. Select the “DATA RECORD” type and press “ENTER”.

  31. Hi-Scan Pro Application 1.6 FLIGHT RECORD – AUTO TRIGGER (2/2) Choose items to record: all or custom. • USER SELECT DATA RECORD. : Record user defined sensor data. • FIX : Select sensors to record in ‘USER SELECT DATA RECORD”. • ENTER : Start “RECORDING” • ESC :”STOP” recording • ALL DATA RECORD : Record all sensor data “01” ENTER “02” ENTER

  32. Hi-Scan Pro Application 1.6 FLIGHT RECORD – AUTO TRIGGER (SINGLE DTC) Enter specific DTC which will be used as trigger. ENTER • AUTO TRIGGER(SINGLE DTC) • : Record user defined single DTC. • Type specific “DTC CODE” and press “ENTER”. • Rest of procedures are same as “AUTO TRIGGER (ANY DTC)” Type DTC CODE and press ENTER

  33. Hi-Scan Pro Application 1.6 FLIGHT RECORD – MANUAL TRIGGER (1/2) User triggers the record data. • MANUAL TRIGGER : Place a mark on a recorded data where “ENTER” button is pressed while recording. This mark is displayed as vertical line in “GRAPH” mode. • Next procedures are same as “AUTO TRIGGER”. • Select “DATA RECORD” type. Same procedure as “AUTO TRIGGER”

  34. Hi-Scan Pro Application 1.6 FLIGHT RECORD– MANUAL TRIGGER (2/2) Choose items to record: all or custom. “01” ENTER • USER SELECT DATA RECORD. : Record user defined sensor data. • FIX : Select sensors to record and press “F1”. • ENTER : Start “RECORDING”. • ENTER : Start “TRIGGERING”. • ESC :”STOP” recording. “02” ENTER • ALL DATA RECORD : Record all sensor data • ENTER : Place a mark on a data where “ ENTER” is pressed while recording.

  35. Hi-Scan Pro Application 1.6 FLIGHT RECORD –FLIGHT RECORD VIEW (1/2) Review recorded data. ENTER • FLIGHT RECORD DATA REVIEW : Review recorded data. • Select the memory location, then press “ENTER”. • Press “ENTER” to review recorded data. Select the memory location and press “ENTER”

  36. Hi-Scan Pro Application 1.6 FLIGHT RECORD –FLIGHT RECORD VIEW (2/2) Select review type. ENTER • GRAP : Covert the “LIST” screen into “GRAPH”. • LIST : Covert the “GRAPH” screen into “LIST”. • HOME : Place the triggered position, displayed as vertical line, at the middle of the screen. • FIX : You can scroll up and down without moving fixed item. If you press “FIX” again, you can change the item to fix. F1 “GRAP” F1 “LIST”

  37. Hi-Scan Pro Application 1.7 DUAL DISPLAY Inspect the sensor or actuator data and DTC Previous menu ENTER ENTER ENTER ENTER ENTER F1 FIX F2 CURR F3DTC • Hi-Scan Pro can display both DTC and sensor data simultaneously. • Use can check the sensor data which with DTC. • FIX : Fix sensor data • CURR : Activate current data • DTC : Activate DTC data Select “DUAL DISPLAY” in “KIA VEHICLE DIAGNOSIS” mode. In this case, connect with vehicle via DLC cable.

  38. Hi-Scan Pro Application 1.8 SIMU-SCAN (1/4) Simulate and scan sensor or actuator simultaneously ENTER ENTER ENTER ENTER ENTER F2 SIML F1 METER Previous menu • METER : voltage, frequency, duty, current, temperature and pressure meter • SIMUL : voltage, frequency, duty, simulation Select “SIMU-SCAM” in “KIA VEHICLE DIAGNOSIS” mode. In this case, connect with vehicle via DLC cable and test probe.

  39. Hi-Scan Pro Application 1.8 SIMU-SCAN (2/4) To measure the sensor data and compare with scan data F1 METER • METER MODE : One of the most powerful feature of Hi-Scan Pro is SIMU-SCAN, in which sensor output data is measured and current data is displayed simultaneously that user can compare actual data and ECM data. • : This figure is an example of SIMU-SCAN screen for ECT sensor. PRESS “1” BUTTON ON KEY PAD

  40. Hi-Scan Pro Application To measure the sensor data and compare with scan data F1 METER 1.8 SIMU-SCAN (3/4) • METER MODE : This is an example of SIMU-SCAN screen for ISC on time. PRESS “2” BUTTON ON KEY PAD PRESS “5” BUTTON ON KEY PAD

  41. Hi-Scan Pro Application F2 SIML 1.8 SIMU-SCAN (4/4) To measure the sensor data and compare with scan data • SIMU MODE :This is an example of SIMU-SCAN screen for TPS sensor with generated voltage 2V. • NOTICE : SIMU MODE activate on channel B only. SELECT NUMBER “1” OF KEY PAD

  42. Hi-Scan Pro Application 2. VEHICLE SCOPEMETER 2.1 Part analysis - Engine : 17 items - Auto T/A : 9 items 2.2 Manual scope 2.3 Meter(V,F,R,A,T,P) 2.4 Actuator driving 2.5 Sensor simulator

  43. ENTER Hi-Scan Pro Application 2.1 PART ANALYSIS (1/2) Analyze part precisely in pre-set oscilloscope mode Select “VEHICLE SCOPEMETER” in “INITIAL SCREEN” and select “KIA VEHICLE AUTO SCOPE”. Connect a test probe to “CH A” of Hi-Scan Pro and tap probe pin into appropriate signal wire of sensor or actuator. • Provides easier component inspection and more effective with pre-set DB support and reference waveform. • KIA VEHICLE AUTO SCOPE : Pre-set oscilloscope for KIA vehicles. • MANUAL SCOPE : Oscilloscope mode. • METER : Multi-meter mode. • ACTUATOR DRIVING : Test drive “ACTUATOR”. • SENSOR SIMULATOR : Send dummy data to inspect status of sensors.

  44. Hi-Scan Pro Application 2.1 PART ANALYSIS (2/2) Analyze part precisely in pre-set oscilloscope mode ENTER ENTER ENTER • ENGINE : 17 items. • A/T : 9 items

  45. Hi-Scan Pro Application 2.1 PART ANALYSIS ---- ENGINE : SENSOR (1/2) Analyze part precisely in pre-set oscilloscope mode PREVIOUS MENU ENTER ENTER ENTER • Engine sensor mode has 17 pre-set items. • User have to connect test probe to “CH A”, and prick probe pin to sensor signal wire. ENTER

  46. Hi-Scan Pro Application 2.1 PART ANALYSIS ---- ENGINE : SENSOR (2/2) Analyze part precisely in pre-set oscilloscope mode PREVIOUS MENU ENTER ENTER ENTER ENTER • CKP SENSOR • TIPS : Sensor information. • WAVE : Reference waveform of sensor. • AUTO SET DB SUPPORT - Voltage, Time, Trigger Level. WAVE ENTER TIP

  47. Hi-Scan Pro Application 2.1 PART ANALYSIS ---- ENGINE : ACTUATORS Analyze part precisely in pre-set oscilloscope mode PREVIOUS MENU ENTER ENTER ENTER ENTER ENTER WAVE • INJECTOR • TIPS : Actuator Information. • WAVE : Reference Waveform of sensor. • AUTO SET DB SUPPORT – Voltage, Time, Trigger Level. TIP

  48. Hi-Scan Pro Application 2.1 PART ANALYSIS ---- ENGINE : IGNITION Analyze part precisely in pre-set oscilloscope mode PREVIOUS MENU ENTER ENTER ENTER ENTER ENTER • 1’ST IGNATION WAVE • WAVE : Standard waveform of sensor • AUTO SET DB SUPPORT - Voltage, Time, Trigger Level. WAVE

  49. Hi-Scan Pro Application 2.1 PART ANALYSIS ---- Automatic Transmission Analyze part precisely in pre-set oscilloscope mode ENTER ENTER • Automatic Transaxle mode has 9 pre-set items.

  50. Hi-Scan Pro Application 2.2 MANUAL SCOPE User defined oscilloscope. Select “VEHICLE SCOPEMETER” in “INITIAL SCREEN” and select “VEHICLE SCOPEMETER”. Connect a test probe to “CH A” or “CH B” of Hi-Scan Pro and tap into signal wire of sensor or actuator. ENTER

More Related