1 / 16

AllSign Printer Driver Software Installation Manual

AllSign Printer Driver Software Installation Manual. 1.Choose the correct setup Attention: For softare USB 128+ v1.4 You need to connect to the boards then you can open the software. otherwise it will close automaticlly.( Konica software doesn't have this issue).

dustin
Download Presentation

AllSign Printer Driver Software Installation Manual

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. AllSign Printer Driver Software Installation Manual

  2. 1.Choose the correct setupAttention: For softare USB 128+ v1.4 You need to connect to the boards then you can open the software. otherwise it will close automaticlly.( Konica software doesn't have this issue)

  3. 2.You can see MTYPE to know which modle you need to choose

  4. 3. See all types

  5. 4. Check PHC picture and you will understand which oneyou need to choose

  6. 5. Install the XTUSB for the Printer driver (Mainboard driver). And double click the "Sentinel Keys" to install theUSB key driver (If you have password with the boards, you need to put the USB key into the computer )After you install the driver, and connect to the printer, you can find the " USB printer" in your hardware -Devicen manager)

  7. 6. Open the software and input the password at "Menu"

  8. 7.Password is"000000"

  9. 8. Please adjust to the correct setup in Print Option. Note: Idle Flash Freq is 50HZ. High flash: 2000HZ

  10. 9. Task Select : It is where you choose your ripped file and see printing status.

  11. 10. Operation: It is where you can set the margin and choose Printing speed and direction

  12. 11. Maintance-Calibration. Please click "Default" to restore all the parameter before you adjust .

  13. 12. Maintance-Motion: It is very important here. X speed: Min Speed:100 Max speed: 1000mm/s Acceeration:2000 mm/s2 and Calculater to automatic set the parameter for X direction.( you need to check in different positions -left , middle and right side in the printing bed. If you get close number then ok, but if you got very big difference you must check that postion---the raster bar is not installed good )Y speed: Acceleration: 2000mm/s2 Motion factor: Adjust the number until you get real size.( for example: you set 100MM for Y moving. and you get 100MM in actual )Zero Position: 15mmMust choose: X Dir reverse Y Dir Reverse Limit Signal Reverse Pluse Phase ReverseAfter you set all please Click " APPLY " to save the parameter

  14. 13. If you are using Konica software there will be another option in Maintainance called" Voltage "This is where you set the voltage for Each Konica print heads. It is very important and you must adjsut the voltage until you got perfect printing in each color(No nozzle blocked at high speed printing)--Small tips: Please check the Subtank ink level to insure high speed printing.(Konica and Proton's level will be higher than the 128Plus, if the level is not enough there will be air inside the tube and heads got blocked during printing. If the level is too high then you got ink drop at the bottom of the head, then the heads will be blocked.Note: For both 42PL and 14PL. You must choose TC_5.5MIf the Infactor Curve Option is not choosed. There will be error in loading software and you must set this first.Most important: To open Konica software You must Turn on the Printhead voltage button.

  15. 15. If you want to uninstall the software please click the "Setup" to uninstall. DO NOT DELETE THE FOLDER AT YOUR PROGRAM FILES

  16. 16. If you are setting Myjet 128+ PCI software. PLease pay attention:1. Reset Speed: 100mm/s 2.Acceleration: 200ms3. Select "Carriage Direction Convert" "Limit Switch Valid Signal Convert" "Advance Direction Convert"

More Related