1 / 19

Smart Surge Protector

Smart Surge Protector. Team Members Jason Long & Billy Gates, Jr. Professor Stephen E. Saddow, Advisor. Motivation. Most residential surge protection devices fail without warning. Some have indicator lights that are difficult to see.

elina
Download Presentation

Smart Surge Protector

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Smart Surge Protector Team Members Jason Long & Billy Gates, Jr. Professor Stephen E. Saddow, Advisor

  2. Motivation • Most residential surge protection devices fail without warning. • Some have indicator lights that are difficult to see. • A smart surge protection device that reports the status of the surge protection element (varistor) to the user via a computer interface. • A GUI (Graphic User Interface) will be used to report the status to the user after reading the status of the monitoring circuit.

  3. Team Members Dr. S. E. Saddow JasonLong Billy J Gates,Jr.

  4. Team Organization Billy J Gates, Jr. • Monitoring interface Presentation organization • Computer program • Web Page • Executive Summary • Test Specifications • Objective Jason Long • Requirements • Objectives • References • Web Page • Problem Statement • Surge Protection circuit

  5. How to observe the protection device state? 1. LED’s Are not always visible to user 2. Alarms Are often ignored by user 3. Our design Give the user a computer prompt of the status of the device as it reaches the end of its lifetime.

  6. Abstract • A monitoring surge protection device that reports the status of the surge protection circuit (varistor) to the computer. • A GUI (Graphic User Interface) will be used to report the status to the user, by reading the status of the monitoring circuit.

  7. Objective 1. TestSource voltages: The Surge Protection Device (SPD) will operate from any standard 125V three-prong receptacle outlet that is designed for 120 VAC 60Hz. 2.Fire Standards: The device will meet all the National Fire and Safety Code and the National Electrical Codes. 3.Physical Packaging: We are not so much concerned with the physical packaging at the moment, although we know the design will be contained in a molded plastic case. The main concern will be getting the design to work. 4.Monitoring Time: We will check the status of the varistor for any changes caused by an over-voltage or over-current every 1s.

  8. Objective 5. Transient Voltage Surge Suppression: The SPD will be designed to suppress a continuous transient voltage of 135V AC. 6. Clamping Voltage: “Clamping” is the term used for the process whereby surge protection devices reduce or attenuate transients and limit the surges reaching the protected load to a specific lower voltage level. The lowest clamping voltage recognized by United Laboratories (UL) is 330 V in the UL1449 standard. Rise time for the voltage must be within the 8s (microseconds), and with a 20s trail off. 7. Peak transient current: The SPD will be able to handle a peak transient voltage of 1200 Amps. Rise time for the current must be within the 8s (microseconds), and with a 20s trail off.

  9. Objective 8. Operation Indicator (Graphical User Interface): Our SPD operation indicator will be a graphical user interface. The graphical user interface will give the user the number of times the SPD has been placed in it protection mode (against over- voltage and over-currents) and the number of times the SPD has before the device fails. This information will be gather via a RS-232 serial port. 9.Surge Protection: The SPD will protect against transient voltage surges line to neutral, line to ground, and neutral to ground. 10. Measuring circuit: This circuit will trigger if an over-current or over- voltage thru the varistor. Triggering a counter that will hold the number of times the varistor has been activated for protection. We will use a battery to power the counter in the event of power loss. 8.

  10. Approach • Computer Program C++ • Simulation PSPICE & Electronics Workbench • Hardware Varistor RS-232 interface counter

  11. Design MONITORING CIRCUIT 1000 V, 100A 100 KHZ PEARSON COIL 355 V CLAMPING LEVEL L TRANSIENT CURRENT IS SHUNTED L-N BY SPD COMPONENT RESISDUAL TRAVELS ON TO LOAD LOAD SINGLE SPD COMPONENT TRANSIENT RESIDUAL SHUNTED TO NEUTRAL ENERGY DISAPATED AS HEAT DURING CLAMP N G

  12. Design METAL OXIDE VARISTOR SMART SURGE PROTECTION DEVICE GRAPHICAL USER INTERFACE 4. PEARSON COILS AND COMPARITOR C++ COMPUTER PROGRAM SURGE MONITORING CIRCUIT RS-232 PORT

  13. Design 4. Monitor circuit Surge Protector Computer

  14. Design Surge Protection device This part of the circuit will consist of a varistor that will go into its active mode when an over-voltage or over-current occurs. Monitoring Circuit This part of the will trigger when a over-voltage or over-current occurs. To detect the over-voltage or over-current will sample the operation of the varistor when it is in its active mode. Counter The counter will be incremented each time the varistor is in it active mode. Computer Program(GUI) The program will have a preset value for the counter and it will check the counter for the maximum allowed count and warn the user by prompting the user with a visible icon on the computer screen.

  15. Design Maximum Continuous Voltage RMS = 135 Vac, Maximum Transient Energy = 10 Joules Peak Transient Current = 1200 amps, Maximum Clamping Voltage = 355 V, Transient Power Dissipation = .25 W METAL OXIDE VARISTOR PEARSON COIL Maximum Peak Current = 2000 amps, Useable Rise Time = 20ns Maximum RMS Current = 25 amps SURGE MONITORING CIRCUIT Op-amp, comparator, and current meterThis part of the will trigger when a over-voltage or over-current occurs. To detect the over-voltage or over-current will sample the operation of the varistor when it is in its active mode. GRAPHICAL USER INTERFACE C++ ProgramThe program will have a preset value for the counter and it will check the counter for the maximum allowed count and warn the user by prompting the user with a visible icon on the computer screen.

  16. Test Specifications • Circuit Simulations Used to test component design • Software Software used to check the status of device

  17. Test Specification Requirements SPD Surge Test Monitoring Circuit Test C ++ Simulation Active Modes Fire Safety Code Pspice Simulations Input voltages Fire Standards Physical Packing Transient Voltage Suppression Clamping Voltage Overload Protection Operation Indicator Monitoring Circuit GUI

  18. Acknowledgements • We would like to thank Dr. Stan Saddow, our advisor for his help in our design project.

  19. References [1] K. Lahti, K. Kannus, K. Nousiainen, “Comparison between the DC leakage currents of polymer housed metal oxide surge arresters in very humid ambient conditions and in water immersion tests,” IEEE Transactions on Power Delivery, vol. 14, no. 1, pp. 163-168, Jan 1999. [2] P. M. Wherett, C. J. Kossman, J. R. Gumley, “New techniques for designing surge protection devices,” Journal of Electrical and Electronics Engineering, Austraila, vol. 19, no.1, pp. 45-50, 1999 [3] M. Akbar, A. Monir, “Failure study of metal-oxide surge arrestors,” Electric Power Systems Research, vol. 50, no.2, pp. 79-82, 1999 [4] M. Aceves, J. Pedraza, J. A. Reynoso-Hernandez, C. Falcony, W. Calleja, “Study on Al/silicon rich oxide/Si structure as a surge suppressor, DC, frequency response and modeling,” Microelectronics Journal, vol. 30, no. 9, pp. 855-862, 1999. [5] T. A. Short, R.H. Ammon, “Monitoring results of the effectiveness of surge arrester spacings on distribution line protection.” IEEE Transactions on Power Delivery, vol. 14, no.3, pp. 1142-1150, 1999. [6] D. R. Miller, J. J. Woodworth, C. W. Daley, “Watts loss of polymer housed surge arresters in a simulated Florida coastal climate,” IEEE Transactions on Power Delivery, vol. 14, no. 3, pp. 940-947, 1999. [7] A. Piantini, C. V. S. Malagodi, “Voltage surges transferred to the secondary of distribution transformers,” IEE Conference Publication, vol. 1, no. 467, pp. 1.365.P6-1.368.P6, 1999. [8] H. Sugimoto, A. Asakawa, S. Yokoyama, K. Nakada, “Effectiveness of installing two pairs of distribution surge arrestors in parallel,” IEE Conference Publication, vol. 2, no. 467, pp.2.246.S13-2.249.S13, 1999. [9] F. Perrot, “Efficient method to characterize the performance of metal oxide varistors,” IEE Conference Publication, vol.2, no. 467, pp. 2.305.P1-2.308.P1, 1999. [10] W. Bassi, N. Matsuo, A. Piantini, “Currents and charge absorbed by low-voltage SPDs in overhead distribution systems due to lightning,” IEE Conference Publication, vol. 2, no. 467, pp. 2.349.P1-2.352.P1, 1999.

More Related