1 / 8

VMM2 SRS Hybrid

VMM2 SRS Hybrid. S. Martoiu, A. Rusu IFIN-HH/CERN. VMM2 SRS Hybrid. PCB design by Alex Rusu Design being released for fabrication Dimensions: 80 x 50 mm VMM and FPGA on the “Panasonic” side. LDOs and a few caps on the other side Prototype completion < 2 weeks

elvina
Download Presentation

VMM2 SRS Hybrid

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. VMM2 SRS Hybrid S. Martoiu, A. Rusu IFIN-HH/CERN

  2. VMM2 SRS Hybrid • PCB design by Alex Rusu • Design being released for fabrication • Dimensions: 80 x 50 mm • VMM and FPGA on the “Panasonic” side. • LDOs and a few caps on the other side • Prototype completion < 2 weeks • Higher quantity production depends on VMM2 availability in quantity.

  3. VMM2 SRS Hybrid • Spartan6 LX9/16 FPGA for VMM control/data acquisition • 1 x Micro HDMI for DAQ • Clk (40MHz) • TTC and configuration (400Mbps – 10b8b) • 2x data lines (400Mbps – 10b8b) • (opt.) ART info over data lines • 1 x Micro HDMI for ART • Buffered ART signals • (opt.) clk, ttc • Power in via HDMI (> 2.7 V) • On-board LDOs • 4 x 1.2V (analog, a/d, digital, fpga) • 1x 2.5V (fpga) • ADP1755 (reported to be rad tolerant up to > 2KGy https://indico.cern.ch/event/310595/session/0/contribution/12/material/slides/0.pdf )

  4. Evaluation Firmware 400Mb/s VMM CTRL TTC 10b/8b HDMI serdes VMM 40 MHz (BC) VMM x 2 160MHz DDR DATA serdes DAQ FIFO 8b/10b HDMI serdes 400Mb/s VMM channel (x2) TTC and Control channels use one HDMI high-speed line with 8b/10b encoding scheme. Direct data flow (no L1A selection) with 8b/10b encoding over 2 x HDMI lines (one for each VMM)

  5. Evaluation Firmware 400Mb/s VMM CTRL TTC 10b/8b HDMI serdes VMM 40 MHz (BC) ART serdes VMM x 2 160MHz DDR DATA serdes DAQ FIFO 8b/10b HDMI serdes 400Mb/s VMM channel (x2) IDLE K DATA DATA 0 K ART ART ADDR DATA 1 DATA 2 DATA 3 IDLE (Optional) high-priority ART channel interleaved on the data line (planned) Second HDMI port is used for a separate ART path (buffered ART signals).

  6. Evaluation Firmware 400Mb/s VMM CTRL TTC 10b/8b HDMI serdes VMM 40 MHz (BC) CFG serdes CFG FIFO ART serdes VMM x 2 160MHz DDR DATA serdes DAQ FIFO 8b/10b HDMI serdes 400Mb/s 40MHz CFG serdes CFG FIFO VMM channel (x2) Control loop is shared with the TTC,Control and Data path on a low priority basis Redundant control and configuration via I2C Remote FPGA re-configuration (planned)

  7. Evaluation Firmware 400Mb/s VMM CTRL TTC 10b/8b HDMI serdes VMM 40 MHz (BC) CFG serdes CFG FIFO ART serdes VMM x 2 160MHz DDR DATA serdes DAQ FIFO 8b/10b HDMI serdes 400Mb/s 40MHz CFG serdes CFG FIFO VMM channel (x2) Evaluation firmware fits in LX9 with enough margin. Planning to install LX16 anyway for future developments.

  8. Summary • PCB design completed, soon under fabrication in prototype run • Fast assembly queued, prototype turnaround should be less than 2 weeks • Minimal firmware is done, SRS application firmware under development. • Higher volume production depends on VMM2 availability in qty.

More Related