1 / 26

Simulated Inductance

Simulated Inductance. Experiment 25. Modification from Lab Manual. Write a MatLAB program Determine the transfer function Calculate the output voltage in phasor notation at the corner frequency. obtain a Bode plot Plot of AC Sweep in PSpice simulation y-axis should be in dB

gavrilla-rios
Download Presentation

Simulated Inductance

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Simulated Inductance Experiment 25

  2. Modification from Lab Manual • Write a MatLAB program • Determine the transfer function • Calculate the output voltage in phasor notation at the corner frequency. • obtain a Bode plot • Plot of AC Sweep in PSpice simulation • y-axis should be in dB • Frequency range from 1 kHz to 10 MHz • Construct a gyrator that has an effective inductance of 10mH. • Compare the operation of the gyrator with the 10mH inductor in an RL circuit where R = 2 kW.

  3. Gyrator • Inductors are far from ideal devices • Parasitic resistance because of the length of wire used to form the inductor. • Parasitic capacitance because of coupling between parallel loops of wire.

  4. Integrated Circuits • Inductors are three dimensional devices, usually free standing • Very difficult to fabricate using standard semiconducting processes and to integrate in a silicon wafer.

  5. Gyrator • Operational Amplifier circuit that has a frequency response similar to an inductor.

  6. Low Pass RL Filter At 0Hz, Vout = Vin. As the frequency increases and the inductor begins to act like an open, Vout approaches 0V.

  7. Bode Plot of Resistor Voltage vs. Vin

  8. High Pass RL Circuit At 0Hz, Vout = 0V. As the frequency increases and the inductor begins to act like an open, Vout approaches Vin.

  9. High Pass RL Filter

  10. Voltage Transfer Function Plot:High Pass RL Filter

  11. Bode Plot:High Pass RL Filter

  12. Phase Plot: High Pass RL Filter

  13. Low Frequency Response:As Expected

  14. Higher Frequency Response:Limited by Op Amp

  15. Information from 741 Datasheet Operational Amplifiers are designed to have large open loop gain. But, the frequency response of the circuit has been sacrificed to achieve this.

  16. Temperature and Frequency Dependence of Open Loop Gain

  17. Applications for Gyrator • Low frequency (f < 500 kHz) applications in: • Audio Engineering • Biomedical Engineering • Certain areas of power electronics

  18. MatLAB

  19. Defining a Vector Three elements t=[0,.1,3] or t=[0 .1 3] t = 0 0.1000 3.0000 Four Elements t=[0:3] t = 0 1 2 3 Elements that include 0, then 0.1, and then increments of 1 until it reaches the largest number ≤ 3 t=[0,.1:3] t = 0 0.1000 1.1000 2.1000 Thirty one elements between 0 and 3 in increments of 0.1 t=[0:.1:3] t = 0 0.1000 0.2000 0.3000 0.4000 0.5000 0.6000 0.7000 0.8000 0.9000 1.0000 1.1000 1.2000 1.3000 1.4000 1.5000 1.6000 1.7000 1.8000 1.9000 2.0000 2.1000 2.2000 2.3000 2.4000 2.5000 2.6000 2.7000 2.8000 2.9000 3.0000

  20. MatLAB Suppose you have determined that the transfer function for your filter is: • You can put this transfer function into MatLAB • Define two vectors • A = [An, An-1, ….., A1, A0] where n, m ≥ 0 and • B = [Bm, Bm-1, ….., B1, B0] n does not have to equal m • H = tf(A,B)

  21. Example High pass filter with a single-pole/single-zero • Let RC = 104 s/rad • A = [0, 10e3] • B = [1 10e3] • H = tf(A,B) 10000s H = --------- is returned when you run the program 10000s + 1

  22. MatLAB: Bode Plots • Once you have entered the transfer function into MatLAB, you can use a predefined function ‘bode’ to automatically generate plots of the magnitude and phase vs. frequency. Enter: bode(H)

  23. Bode Plot Parameters

  24. Complex Numbers • The default symbol for √-1 is i. However, MatLAB does recognize that j is equivalent to i. • The coefficient of the imaginary number must be placed before the ‘i’ or ‘j’. • If you typed c = 2-3j, MatLAB interprets it as c = 2.0000 - 3.0000i • To find components of complex number • real(c) returns 2 • imag(c) returns -3

  25. Magnitude and Phase • Magnitude of a complex number • Is the square root of the square of the real component plus the square of the imaginary component • Phase of a complex number • Is the arc tangent of the imaginary component divided by the real component • Must change to degrees if the output of the arc tangent is given in radians

More Related