1 / 19

ECL FINESSE status

ECL FINESSE status. Vladimir Zhulanov BINP, Russia 2008.07.04. Algorithm details. Reconstruction options. ADC data  amplitude reconstruction is needed somewhere In FINESSE In COPPER In event builder. Hardware data processing. Advantages:

germane-olson
Download Presentation

ECL FINESSE status

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. ECL FINESSE status Vladimir Zhulanov BINP, Russia 2008.07.04

  2. Algorithm details

  3. Reconstruction options ADC data  amplitude reconstruction is needed somewhere • In FINESSE • In COPPER • In event builder

  4. Hardware data processing Advantages: • Low data amount transferred from FINESSE to COPPER • Low processing load of the COPPER CPU Disadvantages: • Inflexible realization – the algorithm must be strictly defined and intensively tested

  5. FPGA overall design DDR 1 DDR 2 FPGA DSP ADC DATA PROCESSOR + buffer for 320 samples * 64 channel TKO1 TKO2 COPPER EVENT DATA FIFO TKO3 PACKAGER TKO4 TTRX THREAD CONTROLLER

  6. Output data format

  7. Output data format (cont.)

  8. ECL FINESSE initialization • Load driver (once after COPPER boot up): insmod cprfin_ecl.o • Load firmware (once after COPPER boot up): cp he2932.bin /dev/copper/ecl_conf:[ab|cd] • Load DSP coefficients and supplement settings:cp dspfile.ecldsp /dev/copper/ecl_dsp:[ab|cd] • Setup other parameters:user_soft/ecl_setup [ab|cd]or using library cprfin_ecl_lib. The initialization is made via ioctl() calls

  9. ECL FPGA settings There are several kinds of FPGA parameters: • parameters and coefficients concerning DSP – special file • parameters of the synchronization with TKO modules and ADC work. • Masks for DSP and RAW ADC DATA – they must be changed for local run and luminosity run • Decimation factor Fd– how often FPGA stores raw ADC data. Can be set from 1/1 to 1/107

  10. Cosmics reconstruction Reconstruction in FPGA is equal software reconstruction

  11. Reconstructed pedestal

  12. Reconstructed amplitude

  13. Comparition of reconstructed time for 2 channels

  14. Status • The hardware implementation of DSP algorithm is fully debugged (no evidence against that). The hardware result of over then 80000 cosmics events matched sofware version of DSP restoration algorithm. • There are 5 FINESSEs and 8 Shapers ready – That’s enough to serve 1/8 of backward endcap

  15. Installation of new electronics BELLE DAQ 8 Shapers-ADC, located outside of radioactive area roecl01 120 CsI crystalls and Premps of 1/8 of backward endcap Copper with 2 ECL FINESSEs in EFC crate in electronic hut We are going to replace part of current electronics

  16. Current activity • Debugging the ECL DAQ software left by Kiyama.

  17. To do • Install the new new electronics for 1/8 of backward endcap (120 crystalls) • Test data pass to BELLE DAQ • Check hardware DSP implementation and consistency of read out data on cosmics • Measure real noise and coherent noise • Test of DAQ reliability (with and without parallel readout from FASTBUS part of ECL) – tune related software • Measure maximum capable trigger rate • We hope the new electronics and new DAQ will be tested with beam data at October!!!

  18. Thank you for your attention

More Related