Kuat Geser Tanah ( Shear Strength ) (Source : CIL-610 Foundation Engineering)

1. Kuat Geser Tanah(Shear Strength)(Source : CIL-610 Foundation Engineering) oleh: A. Adhe Noor PSH, ST., MT Staf Pengajar Program Studi Teknik Sipil Jurusan Teknik Fakultas Sains dan Teknik Universitas Jenderal Soedirman

2. Steel Concrete Soil Compressive strength Shear strength Tensile strength Presence of pore water Complex behavior Strength of different materials

3. Embankment Strip footing Failure surface Mobilized shear resistance Shear failure of soils Soils generally fail in shear At failure, shear stress along the failure surface (mobilized shear resistance) reaches the shear strength.

4. Retaining wall Shear failure of soils Soils generally fail in shear

5. Mobilized shear resistance Failure surface Shear failure of soils Soils generally fail in shear Retaining wall At failure, shear stress along the failure surface (mobilized shear resistance) reaches the shear strength.

6. failure surface Shear failure mechanism The soil grains slide over each other along the failure surface. No crushing of individual grains.

7.       Shear failure mechanism At failure, shear stress along the failure surface () reaches the shear strength (f).

8.  failure envelope Friction angle Cohesion f c   Mohr-Coulomb Failure Criterion(in terms of total stresses)  f is the maximum shear stress the soil can take without failure, under normal stress of .

9.  ’ failure envelope Effective cohesion Effective friction angle f c’ ’ ’ Mohr-Coulomb Failure Criterion(in terms of effective stresses) u = pore water pressure f is the maximum shear stress the soil can take without failure, under normal effective stress of ’.

10.  f ’f tan ’ frictional component ’ cohesive component c’ c’ ’f ' Mohr-Coulomb Failure Criterion Shear strength consists of two components: cohesive and frictional.

11. c and  are measures of shear strength. Higher the values, higher the shear strength.

12. Laboratory tests on specimens taken from representative undisturbed samples Field tests • Most common laboratory tests to determine the shear strength parameters are, • Direct shear test • Triaxial shear test • Vane shear test • Torvane • Pocket penetrometer • Fall cone • Pressuremeter • Static cone penetrometer • Standard penetration test Determination of shear strength parameters of soils (c, forc’, f’) Other laboratory tests include, Direct simple shear test, torsional ring shear test, plane strain triaxial test, laboratory vane shear test, laboratory fall cone test

13. A representative soil sample z z svc + Ds svc shc shc shc shc svc svc + Ds After and during construction Before construction Laboratory tests Field conditions

14. svc + Ds shc shc Traxial test 0 svc svc + Ds svc shc shc 0 0 t Direct shear test svc 0 t svc Representative soil sample taken from the site Step 1 Set the specimen in the apparatus and apply the initial stress condition Laboratory tests Simulating field conditions in the laboratory Step 2 Apply the corresponding field stress conditions

15. Direct shear test Schematic diagram of the direct shear apparatus

16. Porous plates Components of the shear box Preparation of a sand specimen Direct shear test Direct shear test is most suitable for consolidated drained tests specially on granular soils (e.g.: sand) or stiff clays Preparation of a sand specimen

17. Pressure plate Leveling the top surface of specimen Specimen preparation completed Direct shear test Preparation of a sand specimen

18. Steel ball P Pressure plate Porous plates S Proving ring to measure shear force Step 1: Apply a vertical load to the specimen and wait for consolidation Direct shear test Test procedure

19. Steel ball P Test procedure Pressure plate Porous plates S Proving ring to measure shear force Step 1: Apply a vertical load to the specimen and wait for consolidation Direct shear test Step 2: Lower box is subjected to a horizontal displacement at a constant rate

20. Dial gauge to measure vertical displacement Shear box Proving ring to measure shear force Loading frame to apply vertical load Dial gauge to measure horizontal displacement Direct shear test

21. Direct shear test Analysis of test results Note: Cross-sectional area of the sample changes with the horizontal displacement

22. Shear stress, t Dense sand/ OC clay tf Loose sand/ NC clay tf Shear displacement Expansion Dense sand/OC Clay Change in height of the sample Shear displacement Loose sand/NC Clay Compression Direct shear tests on sands Stress-strain relationship

23. Shear stress, t Normal stress = s3 Normal stress = s2 Shear displacement Normal stress = s1 tf2 tf1 tf3 Shear stress at failure, tf Mohr – Coulomb failure envelope f Normal stress, s Direct shear tests on sands How to determine strength parameters c and f

24. Some important facts on strength parameters c and f of sand Direct shear tests on sands Direct shear tests are drained and pore water pressures are dissipated, hence u = 0 Sand is cohesionless hence c = 0 Therefore, f’ = f and c’ = c = 0

25. Overconsolidated clay (c’ ≠ 0) Shear stress at failure, tf Normally consolidated clay (c’ = 0) f’ Normal force, s Direct shear tests on clays In case of clay, horizontal displacement should be applied at a very slow rate to allow dissipation of pore water pressure (therefore, one test would take several days to finish) Failure envelopes for clay from drained direct shear tests

26. Where, ca = adhesion, d = angle of internal friction Interface tests on direct shear apparatus In many foundation design problems and retaining wall problems, it is required to determine the angle of internal friction between soil and the structural material (concrete, steel or wood)

27. THE END