1 / 49

6 장 Transmission of Digital Data: Interfaces and MODEMs

6 장 Transmission of Digital Data: Interfaces and MODEMs. 6.1 Digital Data Transmission 6.2 DTE-DCE Interface 6.3 Other Interface Standards 6.4 모뎀 (MODEM) 6.5 요약. 6.1 Digital Data Transmission.

heinz
Download Presentation

6 장 Transmission of Digital Data: Interfaces and MODEMs

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. 6장 Transmission of Digital Data: Interfaces and MODEMs 6.1 Digital Data Transmission 6.2 DTE-DCE Interface 6.3 Other Interface Standards 6.4모뎀(MODEM) 6.5 요약

  2. 6.1 Digital Data Transmission ~ of primary concern when considering the transmission of data from one device to another is the wiring

  3. Digital Data Transmission(cont’d) • parallel Transmission ~ By grouping, we can send data n bits at a time instead of one • 장점 : 속도(speed) • 단점 : 고가(expansive) 전송거리(short distance): 최대25 feets

  4. Digital Data Transmission(cont’d) • Parallel transmission

  5. Digital Data Transmission(cont’d) • Serial Transmission ~ one bit follows another • 장점 : 단일 channel, 저가 • 단점 : require interface converter

  6. Digital Data Transmission(cont’d) • Serial Transmission

  7. Digital Data Transmission(cont’d) • 비동기 전송(Asynchronous Transmission) ~ send one start bit(0) at the beginning and one or more stop bits(1) at the end of each byte

  8. Digital Data Transmission • 동기전송(synchronous transmission) ~ send bits one after another without start/stop bits or gaps. It is the responsibility of the receiver to group the bits • 장점 : 속도(speed)

  9. 6.2 DTE-DCE Interface • DTE(Data Terminal equipment) : 데이터 단말장치 • DCE(Data Circuit-terminating Equipment) : 데이터 처리 종단 장치

  10. DTE-DCE Interface(cont’d) • DTE(Data Terminal Equipment) ~ is any device that is a source of destination for binary digital data • terminal • microcomputer • computer • printer • fax machine and so on

  11. DTE-DCE Interface(cont’d) • DCE(Data Circuit-Terminating Equipment) ~ is any device that transmits or receives data in the form of an analog or digital signal through a network • Modulator/demodulator

  12. DTE-DCE Interface(cont’d) • 표준안(Standards) ~ to define the connection between a DTE and DCE

  13. DTE-DCE Interface(cont’d) • Standards • EIA • EIA-232 • EIA-442 • EIA-449 • ITU-T • V series (전화망에 관한 데이터 통신) • X series (데이터 통신망에 대한 데이터통신)

  14. DTE-DCE Interface(cont’d) • EIA-232(RS-232) ~ defines the mechanical, electrical and functional characteristics • 기계적인 면(mechanical) ~ define the interface as a 25-wire cable with a male and a female DB-25 pin connector ~ length may not exceed 15m(50 feet) • 전자적인 면(electrical specification) ~ define voltage levels and the type of signal(예: NRZ-L)

  15. DTE-DCE Interface(cont’d) • sending the data ~ To be recognized as data, the amplitude of a signal must fall between 3 and 15 volts or between –3 and –15 volts

  16. DTE-DCE Interface(cont’d) • control and timing ~ Signals must be sent using OFF less than –3 volts and ON greater than +3 volts

  17. DTE-DCE Interface(cont’d) • 기능 적인 면(Functional Specification)

  18. DTE-DCE Interface(cont’d) • 예: synchronous full-duplex transmission

  19. DTE-DCE Interface(cont’d)

  20. DTE-DCE Interface(cont’d) • Null Modem ~ not needed to connect two compatible digital devices directly • Using regular data pin connections with and without DCEs

  21. DTE-DCE Interface(cont’d) • Crossing Connections • Null modem pin connection

  22. 6.3 Other Interface Standards ~ needs more speed and/or distance • EIA-449 • EIA-530 • X.21

  23. Other Interface Standards(cont’d) • EIA-449 • DB-37 pin • DB-9 pin • DB-37 and DB-9 connections

  24. Other Interface Standards(cont’d) • Pin Functions • category I pins ~ are compatible with those of EIA-232 • category II pins ~ have no equivalent in EIA-232

  25. Other Interface Standards(cont’d) • DB-37 pins Pin Functions Category Pin Functions Category 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 Shield Signal rate indicator Unassigned Send data Send timing Receive data Request to send Receive timing Clear to send Local loopback Data mode Terminal ready Receive ready Remote loopback Incoming call Select frequency Terminal timing Test mode Signal ground I I I I I I II I I I II II I II Receive Common Unassigned Send data Send timing Receive data Request to send Receive timing Clear to send Terminal in service Data mode Terminal ready Receive ready Select ready Signal quality New signal Terminal timing Standby indicator Send common II I I I I I I I II I I I II II I II II

  26. Other Interface Standards(cont’d) • DB-9 pins Pin Function EIA-232 Equivalent 1 2 3 4 5 6 7 8 9 Shield Secondary receive ready Secondary send data Secondary receive data Signal ground Receive common Secondary request to send Secondary clear to send Send common 1 14 16 7 12 19 13

  27. Other Interface Standards(cont’d) • Electrical specification : RS-423 and RS-422 ~ EIA-449 uses two other standards to define its electrical specification • RS-423 (unbalanced circuits) • RS-422 (balanced circuits)

  28. Other Interface Standards(cont’d) • RS-423 : Unbalanced Mode

  29. Other Interface Standards(cont’d) • RS-422 : Balanced Mode

  30. Other Interface Standards(cont’d) • Canceling of noise using balanced mode

  31. Other Interface Standards(cont’d) • EIA-530 ~ is a new version of EIA-449 that uses DB-25 pins

  32. Other Interface Standards(cont’d) • X.21 ~ is an interface designed by the ITU-T • DB-15 connector

  33. Other Interface Standards • DB-15 pins Pin Function Pin Function Transmit data or control Control Receive data or control Indication Signal element timing Byte timing Reserved 1 2 3 4 5 6 7 8 Shield Transmit data or control Control Receive data or control Indication Signal element timing Bye timing Signal ground 9 10 11 12 13 14 15

  34. 6.4 MODEMs ~ the most familiar type of DCE

  35. MODEMs(cont’d) • MODEM ~ stands for modulator/demodulator • Modulator : converts a digital signal to an analog signal • Demodulator : converts an analog signal to a digital signal

  36. MODEMs(cont’d) • Transmission • Bandwidth ~ Each line has an upper limit and a lower limit on the frequencies of the signals it can carry. This limited range is called the bandwidth

  37. MODEMs(cont’d) • Telephone line bandwidth ~ A telephone line has bandwidth of almost 3000 Hz

  38. MODEMs(cont’d) • Modem speed • ASK(Amplitude Shift Keying) • Baud rate in half-duplex ASK

  39. MODEMs(cont’d) • Baud rate in full-duplex ASK ~ Although ASK has a good bit rate, it is not used today because of noise

  40. MODEMs(cont’d) • FSK(Frequency Shift Keying) • Baud rate in half-duplex FSK

  41. MODEMs(cont’d) • PSK and QAM(비교) Half-Duplex Full-Duplex Encoding 2400 4800 7200 9600 12,000 14,400 16,800 1200 2400 3600 4800 6000 7200 8400 ASK, FSK, 2-PSK 4-PSK, 4-QAM 8-PSK, 8-QAM 16-QAM 32-QAM 64-QAM 128-QAM 256-QAM 19,200 9600

  42. MODEMs(cont’d) • Modem Standards • Bell modem • ITU-T modem

  43. MODEMs(cont’d) • Bell Modems(cont’d)

  44. MODEMs(cont’d) • Bell Modems

  45. MODEMs(cont’d) • ITU-T Modem Standards(cont’d)

  46. MODEMs(cont’d) • ITU-T Modem Standards

  47. MODEMs(cont’d) • ITU-T/Bell Compatibility ITU-T Bell Baud Rate Bit Rate Modulation V.21 V.22 V.23 V.26 V.27 V.29 103 212 202 201 208 209 300 600 1200 1200 1600 2400 300 1200 1200 2400 4800 9600 FSK 4-PSK FSK 4-PSK 8-PSK 16-QAM

  48. MODEMs(cont’d) • Intelligent Modems ~ contain software to support a number of additional function, such as automatic answering and dialing • AT Command[parameter] command[parameter]… • Ex) ATDT4088648902

  49. MODEMs(cont’d) • AT commands Command Meaning Parameters The number to dial 0 or 1 0 or 1 n A B D E H L P T Put modem in answer mode Use V.22bis at 1200 bps Dial the number Enable/disable echo printing Put modem on/off hook Adjust speaker volume Use pulse dialing Use tone dialing

More Related