1 / 32

Network Solutions mcscontrols

Network Solutions www.mcscontrols.com. Presentation Overview. Network Hardware Types Network Protocols Network Adapters MCS-Magnum Communication MicroMag Communication Example Network Configurations. Network Hardware Types. Four network hardware types that are used in MCS products:

hop-green
Download Presentation

Network Solutions mcscontrols

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Network Solutions www.mcscontrols.com

  2. Presentation Overview • Network Hardware Types • Network Protocols • Network Adapters • MCS-Magnum Communication • MicroMag Communication • Example Network Configurations

  3. Network Hardware Types • Four network hardware types that are used in MCS products: • RS485 • RS232 • Ethernet • LonWorks (twisted pair)

  4. RS485 Hardware • One twisted pair (two conductors) • Shielded wire – wrapped foil with drain wire • Minimum AWG 20 • Max baud rate: 115,000 bit/s • Multidrop – point to point • Max 30 MCS Controllers wired together • Total Network cable length < 4000’ (1219m) • Can be lengthened with a repeater

  5. RS232 Hardware • One to one • Three conductor • 9 or 25 pin connecter • Max total cable length < 50’ (15m) • Can be lengthened with a repeater

  6. Ethernet Hardware • Star topography • 4 twisted pairs (8 conductors) • CAT5E • Max baud rate: 10 Mbit/s • Max cable length < 328’ (100m) • Can be lengthened with a switch

  7. LonWorks Hardware • One twisted pair (two conductors) • Shielded wire • Free topography • Minimum AWG 20 • Total Network cable length < 3280’ (1000m) • Can be lengthened with a repeater

  8. Network Protocols • Network protocols are formatting rules that specify how data is sent and received between devices. • Protocols are necessary for devices to interact with each other • Protocols MCS controllers support: • Bacnet • Modbus • LonTalk • Johnson N2 • MCS

  9. Network Protocols • The MCS Controllers support the following network protocols: Over Ethernet Over RS485 Over LonWorks

  10. MCS Network Adaptors • MCS uses five different optional network adapters: • Hardware Adapters • MCS-485-Gateway (RS232 - RS485) • MCS-Ethernet (Ethernet - RS232) • MCS-USB-RS232 (USB - RS232) • Hardware & Protocol Adapters • MCS-BMS-Gateway (Bacnet MSTP, LonTalk, Johnson N2) • MCS-Bacnet-Router2 (Bacnet IP)

  11. MCS-485-Gateway • Converts between • RS485 and RS232 • Used with the MicroMagfor a connection to: • PC (MCS-Connect) • MCS-Touch (MCS-Connect) • MCS-Ethernet • Can be powered from MCS Controller • Only hardware conversion, does not change protocol

  12. MCS-Ethernet • Converts between • Ethernet and RS232 • Used with the MicroMag for Ethernet connection to: • Internet • Comes with 120V wall outlet power adapter • Only hardware conversion, does not change protocol

  13. MCS-USB-RS232 • Converts between • USB and RS232 • Used for PC (MCS-Connect) communication • Powered through USB port • Only hardware conversion, does not change protocol

  14. MCS-BMS-Gateway • Converts Bacnet MSTP (RS485) to: • LonTalk (LonWorks) • Johnson N2 (RS485) • Converts Bacnet IP (Ethernet) to: • LonTalk (LonWorks) • Johnson N2 (RS485) • Bacnet MSTP (RS485) • Only supports one MCS-Magnum or MicroMag • Can be powered from MCS Controller • RS485 • Johnson N2 • Bacnet MSTP Or Ethernet Bacnet IP MCS-Magnum MCS-BMS-Gateway • LonWorks • LonTalk • RS485 • Johnson N2 RS485 Bacnet MSTP MicroMag MCS-BMS-Gateway Or • LonWorks • LonTalk

  15. MCS-Bacnet-Router2 • Converts Bacnet MSTP (RS485) to Bacnet IP (Ethernet) • Supports up to 30 MicroMag • Can be powered from MicroMag • Ethernet • Bacnet IP RS485 Bacnet MSTP MicroMag MCS-Bacnet-Router2

  16. MCS-Magnum Communication • The MCS-Magnum comes with two hardware communication ports: RS485 Port Ethernet Port

  17. MCS-Magnum Communication • The MCS Keypad has a built in MCS-485-Gateway and is connected to the RS485 port on the MCS-Magnum • These two ports cannot be in use at the same time with different protocols: • RS485 port on the MCS-Magnum • RS232 port on the MCS-Magnum Keypad RS232 Port RS485 Bus

  18. MCS-Magnum RS232 • The MCS-Magnum can be connected to a PC via MCS-Connect using RS232 located on the MCS-Magnum Keypad • The PC may require usb to RS232 adapter, MCS Part # (MCS-USB-RS232) • MCS-USB-RS232 MCS-PC9-MM cable PC (MCS-Connect) The RS485 cannot be used with different protocols when the RS232 is used

  19. MCS-Magnum RS485 • Using the RS485, the MCS-Magnum can be connected to the BMS (Modbus RTU or MCS 485) Building Management System . . . RS485 The RS232 cannot be used with different protocols when the RS485 is used

  20. Wiring MultipleMCS Controllers • Using the RS485, the network must be wired controller to controller • Star configurations not allowed • Up to 30 controllers can be wired together Correct Incorrect . . .

  21. MCS-Magnum Ethernet • Using the Ethernet, the MCS-Magnum can be connected to • BMS (Bacnet IP or Modbus IP) • MCS-Touch (MCS-Connect) • PC (MCS-Connect) • Internet access through router (which allows connection via MCS-Connect from anywhere) Or Or Or Ethernet

  22. MicroMag Communication • Ethernet access can be added with the MCS-Ethernet • The MicroMag comes standard with two independent ports: RS485 Port RS232 Port

  23. MicroMag RS232 • The MicroMag RS232 serial port only supports MCS protocol can be used to connect to: • MCS-Touch (MCS-Connect) • PC (MCS-Connect) • The PC may require usb to RS232 adapter, MCS Part # (MCS-USB-RS232) MCS-Touch MCS-PC9-MM cable • MCS-USB-RS232 PC (MCS-Connect) Or

  24. MicroMag RS485 • The MicroMag RS485 port can be used to connect: • MCS-Touch (MCS-Connect) • BMS (Bacnet MSTP or Modbus RTU or MCS 485) Building Management System . . . RS485 Or MCS-Touch

  25. MicroMag RS485 • The MicroMag RS485 port can be used to connect: • MCS-Touch (MCS-Connect) • BMS (Bacnet MSTP or Modbus RTU or MCS 485) • Internet Access using • MCS-485-GATEWAY and the MCS-Ethernet Ethernet . . . RS485 RS232 9pin  25pin Internet Router MCS-ETHERNET MCS-485-GATEWAY

  26. Example Network #1 Standalone MCS-Magnum • MCS-Touch Ethernet Ethernet MCS-Touch

  27. Example Network #2 Standalone MCS-Magnum • MCS-Touch • BMS (Johnson N2 or LonTalk or Bacnet MSTP) • Internet Access RS485 or LonWorks Building Management System MCS-BMS-Gateway Internet Router Ethernet MCS-Touch

  28. Example Network #3 Multiple MCS-Magnum Enclosures • Internet Access • BMS (Bacnet IP or Modbus IP) Rooftop/Chiller #1 Rooftop/Chiller #2 Ethernet Building Management System Internet Router

  29. Example Network #4 Standalone MicroMag • MCS-Touch • BMS (Modbus RTU or Bacnet MS/TP) MCS-PC9-MM cable RS485 MCS-485-Gateway MCS-Touch RS485 Building Management System

  30. Example Network #5 Multiple MicroMags • BMS (Bacnet MSTP or Modbus RTU or MCS 485) • MCS-Touch RS485 MCS-Touch RS232 RS232 Building Management System RS485 RS232

  31. Advanced Example Network Multiple MCS-Magnum & Multiple MicroMag • MCS-Touch • BMS (Bacnet IP) MCS-Touch Building Management System MCS-ETHERNET-SWITCH MCS-Bacnet-Router2

  32. For additional information please visit our website www.mcscontrols.com Or call MCS at 239-694-0089

More Related