1 / 26

Aggregates, Cement and Concrete

Aggregates, Cement and Concrete. MSE 220 Spring, 2009. Rocks come in three types: Igneous – “fire rock” from lava, e.g., granite or obsidian Sedimentary – compacted sediment, e.g., limestone (dead creatures), sandstone

idania
Download Presentation

Aggregates, Cement and Concrete

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Aggregates, Cement and Concrete MSE 220 Spring, 2009

  2. Rocks come in three types: Igneous – “fire rock” from lava, e.g., granite or obsidian Sedimentary – compacted sediment, e.g., limestone (dead creatures), sandstone Metamorphic – Igneous or sedimentary rock transformed under heat and pressure, e.g., slate, marble

  3. Rocks are porous, and can absorb moisture. Oven dry: pores free of moisture Air dry: pores mostly free of moisture Saturated: all pores contain moisture, but none at surface Wet: surface moisture and saturated

  4. Moisture causes fine aggregates to swell more than coarse aggregate Packing improves with mixed sizes of aggregate

  5. Sieve Analysis Sieve analysis gives the percent of aggregate in each pan, as well as the running total percent The “percent coarser than” for all full sieves is summed and divided by 100 to give the “fineness modulus”. The fineness modulus tells us the location of the average aggregate size, in number of pans from the bottom. The size of the openings in a pan are usually ½ that of the preceding pan. This is a “full sieve”. If the pan has a mesh that is larger than ½ the size of the preceding pan, it is a “half sieve”.

  6. Particle Size Distribution Curves Particle Size Distribution curves plot the “percentage coarser than” of aggregate versus the log of the sieve size. A smooth curve means a uniform gradation. A step in the curve (b) means an aggregate size is missing, while an abrupt drop (c) means a bimodal distribution

  7. Grading Requirements The percentage, or amount of each size of aggregate must fall within certain upper and lower limits depending upon the application

  8. Concrete requires more coarse aggregate than mortar

  9. Grading requirements concrete construction, road and bridge construction, and various types of sand Codes also dictate the maximum size of the aggregate, based on the application. Beams: max aggregate = 1/5 narrowest beam section Slabs: 1/3 thickness Rebar: ¾ minimum distance between bars

  10. Ingredients for making Mortar, Grout and Concrete

  11. Hydraulic cements can cure in water – Nonhydraulic cements cannot Sources for the raw materials for making cement

  12. Cement is made up of Calcium Oxide (CaO), or lime), Silicon Dioxide (SiO2) and Alumina (Al2O3), with a minor amount of Iron Cement can be tailored to a specific application by controlling the amount of each constituent compound

  13. Volumetric proportions of constituent materials in concrete

  14. Rate of strength development in concrete For best strength, the ratio of water to cement (w/c) should be kept as low as possible, and cement should be kept moist while curing

  15. Effect of Curing Temperature on Concrete Compressive Strength Strength increases with increased temperature – up to a point

  16. The more “cement rich” the concrete, the stronger it becomes

  17. Maintaining the proper ratios of coarse-to-fine aggregate is key to maximize concrete strength

  18. Concrete is often tested in 3-pt bending, as well as compression

More Related