430 likes | 1.98k Views
Unified-PCMC Ver. 7 TDA100D ver. 5.1 support TDE/NCP ver. 4.2 support. 2011/Jan/19 3rd version. UPCMC v7 series. Each version supports the following. V7.0 : KX-TDA100D v5.1 support. V7.1 : KX-TDE100/200/600, KX-NCP500/1000 v4.2 support. KX-TDA50(USA) v6.0 support.
E N D
Unified-PCMC Ver. 7 TDA100D ver. 5.1 support TDE/NCP ver. 4.2 support 2011/Jan/19 3rd version
UPCMC v7 series Each version supports the following. V7.0 : KX-TDA100D v5.1 support. V7.1 : KX-TDE100/200/600, KX-NCP500/1000 v4.2 support. KX-TDA50(USA) v6.0 support. V7.1.1.5 : Add SA and UA for TDA100D supporting-area.
Common tool specification changing Installer update
Slot structure (1/1) 7th slot is added to the slot structure of current TDA100. 1st - 7th slots are used as free slot.
Four DPT interface ports (DLC4) on MPR (1/1) DLC ports(DLC4) are mounted on MPR. The slot number of MPR is "11” (fixed). DPT:T7600/DT300/VM/DPT-CS/HD-CS can connect to DLC4. The extension number is always assigned from the extension of DLC4.
MCSLC24 and MCSLC26 Card (1/1) Caller ID(FSK only) is supported in new MCSLC24 and MCSLC16. (Do not support the Caller ID for DTMF type) Message Wait that is equivalent of MSLC16. PFT (Two Power Failure Transfer) is available.
CLCOT8/16 Card (1/1) 16ports is available with CLCOT8E card. Caller ID of FSK/DTMF/FSK with Visual CIT type are available. PFT (Two Power Failure Transfer) is available. Pay Tone service is not available. Installation CLCOT8E Card can be checked by Card Property.
Removal of MEC card (1/1) [2.6.2 Quick Dial] MEC 1-100 Expand 1-100 Expansion tab is always displayed [Personal Speed Dialing No.] of [4.1.3 Speed Dial] Personal Speed Dial is always displayed. [6.1 System Speed Dial] Expanded memory for Tenant isalways displayed. [6.2 Hotel & Charge] Billing for Guest (Need MEC card) Billing for Guest
FAX Transfer (1/1) Add the FAX Transfer feature. Add [Fax Extension] in [5.3.2 DISA Message]. Specifies the extension number to which to transfer a call when the MSG card detects a fax signal. This function is supported in TDA30, NCP series, and TDE series.
Quick Setup Improvement (1/1) The user can select Extension and ICD Group Number from pull down list. Improve Quick Setup Add CO Dialing Mode selection
Function supported by other model (1/3) The CTI Port Number range in CTILINK Card is changed. The range is 0,10000-65535.
Function supported by other model (2/3) "24 Ports Analogue Extension Card HOOK Threshold setting" is supported
Function supported by other model (3/3) Improved password protection - The function to prevent login when you incorrectly input the password three times was added. At that time the Error Message(E030113) is displayed. Error Message(E030113) You have reached the maximum number of login attempt. Please login in after a while again. - The password cannot be seen from PCMC. (same as NCP/TDE)
Dealer control (1/3) TDA100D RU/UC, CN TDA100D PCMC refuses connection to ‘other area’ model. PCMC BX TDA100D RU, CN (Different suffix of PBX) Connection Refused !
Dealer control (2/3) TDA100D RU/UC - If Registration Key is not input, you can not use some functions. When you access the following menus, this error isdisplayed. - Port Property of PRI30 - [1.2 Portable Station] - [9.1 TIE Table] You can input the Registration Key from this.
Dealer control (3/3) TDA100D RU/UC • You can also input the Registration Key at • “Tool(T)-License Registration(L)”.
Connect update (1/1) 1. TDA100D is added
New update (1/1) 1. TDA100D is added
PBX Replacement update (1/5) 1. TDA100D V5.1 is supported Support TDA100/200(v5.0) -> TDA100D(v5.1) replacement Note; - If a card is installed inSlot8,Slot9,Slot10 or Slot11, PBX Replacement can not run. It is necessary to delete these cards. - If DHLC8 or SLC8 is installed, PBX Replacement can not run. It is necessary to delete these cards. - If MSLC16,SLC16 or CSLC16 are installed, they are converted to MCSLC16 automatically. - TDA100D -> TDA100/200/600 is not supported. - TDA100D -> TDE100/200/600 is not supported.
PBX Replacement update (2/5) • When you convert the system data of TDA100/200 from versions other than Version 5. • -> You cannot convert the system data and the following error message is displayed. • You have to convert to V.5 before converting to TDA100D .
PBX Replacement update (3/5) • When you convert the system data of TDA100/200 which includes DHLC cards and/or SLC cards. • -> You cannot convert the system data and the following error message is displayed. • You have to remove these cards.
PBX Replacement update (4/5) • When you convert the system data of TDA200 with cards assigned to Slots 8~11. • -> You cannot convert the system data and the following error message is displayed. • You have to remove the cards in Slots 8~11.
PBX Replacement update (5/5) 2. TDE/NCP V4.2 is supported DSYS Converter Note: Because v4.x has common system data format, the output file of DSYS Converter is same between UPCMC v7.0 and v7.1. PBX Replacement Note: Because v4.x has common system data format, the output file of the above PBX Replacement is same between UPCMC v7.0 and v7.1.
Change Suffix code description (1/3) Installer of UPCMC V7 (Suffix) New design for supporting KX-TDA100D.
Change Suffix code description (2/3) Installer of UPCMC V7 (Area selection for NE)
Change Suffix code description (3/3) Installer of UPCMC V7 (Area selection for CE)
Access control to TDA100D You can access the contents of KX-TDA100D only when you select the correct suffix when installing the UPCMC.
Thank You Very Much For Your Attention “ We are Panasonic Family”