How To Fill Cracks In Hardwood Floors

1. How To Fill Cracks In Hardwood Floors

2. Introduction Hardwood floors are aesthetically pleasing and enhance the décor of any house. Keeping them well maintained can be quite challenging and when plank floors or tongue and groove hardwood become old they develop gaps. Many issues arise because of the gaps as these become dirt magnets and cleaning them is not simple. When these boards’ cups and curl they can cause falls or trip hazards.

3. Hardwood Flooring Company Utah Depending on Hardwood Flooring Utah company is the only solution to deal with old wood flooring. When these floorboards are installed on the joists directly, gaps make a room feel drafty. So, when the airflow comes up from the crawlspace or basement the heating system has to work hard to pump heat and it is quite expensive. The developing issue also arises when one tries to fit the nickel on any of the gapped floorboards. You need a wood floor crack repair service at this time. Let’s see why these gaps develop?

4. Why Do the Gaps Develop? For wood flooring Gapping is a very common issue because wood shrinks with time. The problem arises because in the first place boards were not laid correctly initially when they were installed. Secondly, water causes a lot of damage to these floors. Firstly, the wood will swell and then they shrink. Finally, the wood dries out. Just like a furnace room, solid wood flooring that has excess heat below can develop gaps because of dry heat.

5. Can You Fill The Gaps? You need to keep in mind that due to seasonal humidity changes wood contracts and expands. In the winter season you may not notice the gaps, but when the weather is humid one should leave the gaps as it is because if you fill cracks in hardwood floors at that time it will create problems because the wood will expand and contract again. In some cases, the boards can buckle if there is no room left for them to expand. This is the natural tendency of wood and you should fill them during the humid season.

6. Wood Strips To Fill The Gaps: Use a table saw to rip out the strips of the floorboards that are spare and if you cannot get the matching boards then choose the boards of the same species. First, you need to measure the length and width of each gap and then with the table saw rip the cut strips in the desired measurements, but use safety when using the table saw. Take the wood glue and apply it on the side of each strip. Now tap it in the gape gently with the hammer and let the glue dry. Then you can sand down the high spots in the strips. Do not damage the surrounding boards. Now stain the rest of the strips that match with the rest of the floor.

7. Steps To Fill The Gaps: For wide plank boards, a natural fibre rope is ideal to fill the large gaps. Stain the rope so it can blend with the floorboards. The gaps will become less noticeable. Just use jute, cotton, or a natural rope. Synthetic ropes cannot accept stain. First, take a screwdriver and scrape out the gaps. Use a tool to remove the junk, old putty, and dirt. Take care that you do not spoil the floorboard edges. With the help of a vacuum cleaner vacuum the dirt. Now, scrape and vacuum again till the gaps are clean. Choose the size of rope which is larger than the gap and then pour wood stain in the small bucket. Dip the rope in stain so it gets saturated. Now pull out the rope carefully so excess stain drops in the bucket itself. Lay the stained rope on the clean cardboard and let it dry properly. Make sure you do not expose the rope to heat or sunlight else it may catch fire. Along the gap string out the rope and then force it into the gap with the help of a tool or a putty knife.

8. Rope To Fill The Gaps: Choose the size of rope which is larger than the gap and then pour wood stain in the small bucket. Dip the rope in stain so it gets saturated. Now pull out the rope carefully so excess stain drops in the bucket itself. Lay the stained rope on the clean cardboard and let it dry properly. Make sure you do not expose the rope to heat or sunlight else it may catch fire. Along the gap string out the rope and then force it into the gap with the help of a tool or a putty knife.

9. Final Word These are some ways to fill the gaps in the hardwood flooror else get in touch with the best Wood flooring Utah Company near your area to maintain your hardwood floors.