1 / 8

D-NWG-FN-23 Dell Networking Foundations 2023 Real Questions

With the latest D-NWG-FN-23 Dell Networking Foundations 2023 Real Questions from PassQuestion, you will have access to a wealth of valuable information covering all the essential exam topics, giving you the best possible chance of achieving a successful result.

karonchen
Download Presentation

D-NWG-FN-23 Dell Networking Foundations 2023 Real Questions

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Pass Pass DELL DELL D-NWG-FN-23 D-NWG-FN-23 Exam Exam with with Real Real Questions Questions DELL DELL D-NWG-FN-23 D-NWG-FN-23 Exam Exam Dell Networking Foundations 2023 https://www.passquestion.com/ https://www.passquestion.com/D-NWG-FN-23 D-NWG-FN-23.html .html 35% OFF on All, Including D-NWG-FN-23 Questions and Answers P Pass ass DELL DELL D-NWG-FN-23 D-NWG-FN-23 Exam Exam with with PassQuestion PassQuestion D-NWG-FN-23 D-NWG-FN-23 questions questions and and answers answers in in the the first first attempt. attempt. https://www.passquestion.com/ 1 / 8

  2. 1.At which layer of the OSI model is the Rapid Spanning Tree protocol used to prevent switching loops? A. Physical B. Network C. Data Link D. Transport Answer: C 2.Which parameter is required to match an OSPF Adjacency to form? A. IP addresses B. Area ID C. Switch models D. Switch firmware version Answer: B 3.A Dell Networking N3024 has a link aggregation configured as shown: interface Gi1/0/1 channel-group 1 mode active exit ! interface Gi1/0/2 channel-group 1 mode active exit ! interface port-channel 1 switchport access vlan 10 exit After connecting all cables, the port-channel does NOT work as expected. As part of the troubleshooting process, the technician examines the “show lldp” displayed: What is the most likely cause for the issue on the port-channel? A. The interface port-channel is not using 10Gbps interfaces. B. The interfaces on the N2024 switches are running LACP. C. The interface port-channel is not configured in trunk mode. D. The interfaces are connected to different switches. Answer: D 4.A technician configures RIP on a new N-Series switch to connect to an existing switch that runs RIP. The routing table is not populating even after the network statements are added. What is a possible cause of this issue? A. The existing switch has not been configured with the command “hostroutesaccept”. 2 / 8

  3. B. The new switch’s interface is in the wrong subnet to form a RIP relationship. C. The “ip helper-address” command has not been configured on the existing switch. D. The other switch is not a root bridge and cannot form an RIP relationship. Answer: B 5.Which of the following is an optional LLDP TLV? A. Chassis ID B. System Name C. Port ID D. Time-to-live Answer: B 6.A network administrator needs to identify which MAC addresses are static. Under which column in the output of the show mac-address-table command is this information displayed? A. Interface B. Type C. MAC address D. State Answer: B 7.What is the FCS field used for in an Ethernet frame? A. Redirect ICMP messages back to the originator B. Ensure the frame was not corrupted during transmission C. Resolve ARP requests D. Look up the destination address Answer: B 8.What is the size of the ICMP header? A. 8 bits B. 8 bytes C. 16 bits D. 16 bytes Answer: B 9.Which two port states are valid on a root bridge in a converged Spanning Tree network? (Choose two.) A. Blocking B. Designated C. Forwarding D. Listening E. Alternate Answer: AC 10.What is the dotted decimal notation for a /29 prefix? A. 255.255.255.192 3 / 8

  4. B. 255.255.255.252 C. 255.255.255.240 D. 255.255.255.248 Answer: D 11.What is the maximum frequency of a CAT6 UTP cable? A. 100 MHz B. 250 MHz C. 500 MHz D. 600 MHz Answer: B 12.When configuring a switch, which CLI mode only supports limited show commands? A. EXEC B. Maintenance C. Configuration D. EXEC Privilege Answer: A 13.Which command sequence leads to the successful creation of a Layer 3 port channel on an OS10 switch? A. 1(config-if-po-2)# ip address 192.168.0.0/31 S1(config-if-po-2)# no switchport B. S1(config-if-po-2)# ip address 192.168.0.0/31 S1(config-if-po-2)# no switchport C. S1(config-if-po-2)# ip address 192.168.0.0/31 S1(config-if-po-2)# switchport mode IPv4 D. S1(config-if-po-2)# no switchport S1(config-if-po-2)# ip address 192.168.0.0/31 Answer: D 14.Which type of route is often used to direct traffic bound for the Internet? A. Redistributed B. Directly connected C. Dynamic D. Default Answer: D 15.How is a switch different from a hub? A. A switch operates at a lower, more efficient layer of the OSI model. B. A switch decreases the number of broadcast storms. C. A switch tracks MAC addresses of all connected devices. D. A switch does not include any latency into the frame transfer time. Answer: C 4 / 8

  5. 16.Which IEEE standard defines the Data Link Layer, Discovery protocol? A. 802.1AB B. 802.1AX C. 802.1D D. 802.1W Answer: A 17.What does the blinking yellow Activity/PoE LED indicate on an N-Series switch? A. There is no current transmit/receive activity and PoE power is off. B. There is no current transmit/receive activity and PoE power is on. C. There is current transmitting/receiving and PoE power is on. D. There is current transmitting/receiving and PoE power is off. Answer: C 18.On which Dell EMC Networking switches can Multi-Chassis Link Aggregation (MLAG) be configured? A. C9000 Series B. N-Series C. S-Series D. Z-Series Answer: B 19.A Dell EMC Networking N-Series switch is configured on a port channel with LACP using the interfaces Te1/0/1 and Te1/0/2. How is the egress traffic distributed among the interfaces? A. Traffic overflow will be sent to the second interface B. Interfaces will be used in active/passive C. Load balanced per packet using round robin D. Load balanced using a hash function Answer: D 20.Which IPv6 scope is used for private addressing within an organization? A. APIPA B. Area wide C. Global D. Unique local Answer: D 21.Which Border Gateway Protocol (BGP) version supports IPv6? A. BGPng B. BGPv2 C. BGPv3 D. BGPv4 Answer: D 5 / 8

  6. 22.Which IPv6 address type is similar to IPv4 APIPA? A. Multicast B. IPv6 link-local C. Global unicast D. Unique Local Answer: B 23.What attributes does LLDP use to send and receive information about directly connected neighbors? A. Unit Header Value B. Type Length Value C. Unit MAC Frames D. Packets Frames Headers Answer: B 24.What is the correct sequence of steps that occur in the communications between the client and server to obtain an IP address from a DHCP server? Answer: 6 / 8

  7. 25.Which OS6 command is used to verify the running configuration on port 4? A. # show running-config int eth 1/0/4 B. # show running-config int gi 1/0/4 C. # show running-configuration int gi 1/1/4 D. # show running-configuration interface ethernet 1/1/4 Answer: B 26.A network administrator created three VLANs on an Ethernet switch. How many broadcast domains are created by the switch? A. 1 B. 2 C. 3 D. 4 Answer: C 27.Refer to the exhibit. 7 / 8

  8. A technician configures RIP on a new N-Series switch to connect to an existing switch that runs RIP. The new switch routing table is NOT populating even after the correct network statements are added. What is causing this issue? A. The new N-Series switch does not have “default-information originate” configured. B. The existing switch has been configured for “hostroutesaccept”. C. The other switch is a root bridge and cannot form RIP relationships. D. The existing switch is configured to send and receive only for RIPv1. Answer: D 28.How is outbound traffic distributed when using LACP port channels on OS6 switches? A. Load balanced per packet using round robin B. Interfaces are used in active/passive C. Load balanced using a hash function D. Traffic overflow is sent to the second interface Answer: C 29.A static route is denoted with which flag in the routing table? A. C B. S C. T D. R Answer: B 8 / 8

More Related