MASS, MOMENTUM , AND ENERGY EQUATIONS

1. MASS, MOMENTUM, ANDENERGY EQUATIONS

2. This chapter deals with four equations commonly used in fluid mechanics: the mass, Bernoulli, Momentum and energy equations. • The mass equation is an expression of the conservation of mass principle. • The Bernoulli equation is concerned with the conservation of kinetic, potential, and flow energies of a fluid stream and their conversion to each other in regions of flow where net viscous forces are negligible and where other restrictive conditions apply. The energy equation is a statement of the conservation of energy principle. • In fluid mechanics, it is found convenient to separate mechanical energy from thermal energy and to consider the conversion of mechanical energy to thermal energy as a result of frictional effects as mechanical energy loss. Then the energy equation becomes the mechanical energy balance.

3. We start this chapter with an overview of conservation principles and the conservation of mass relation. This is followed by a discussion of various forms of mechanical energy . Then we derive the Bernoulli equation by applying Newton’s second law to a fluid element along a streamline and demonstrate its use in a variety of applications. We continue with the development of the energy equation in a form suitable for use in fluid mechanics and introduce the concept of head loss. Finally, we apply the energy equation to various engineering systems.

4. Conservation of Mass • The conservation of mass relation for a closed system undergoing a change is expressed as msys = constant or dmsys/dt= 0, which is a statement of the obvious that the mass of the system remains constant during a process. • For a control volume (CV) or open system, mass balance is expressed in the rate form as • where min and mout are the total rates of mass flow into and out of the control volume, respectively, and dmCV/dt is the rate of change of mass within the control volume boundaries. • In fluid mechanics, the conservation of mass relation written for a differential control volume is usually called the continuity equation.

5. Conservation of Mass Principle • The conservation of mass principle for a control volume can be expressed as: The net mass transfer to or from a control volume during a time interval t is equal to the net change (increase or decrease) in the total mass within the control volume during t. That is,

6. where ∆mCV=mfinal – minitial is the change in the mass of the control volume during the process. It can also be expressed in rate form as The Equations above are often referred to as the mass balance and are applicable to any control volume undergoing any kind of process.

7. Mass Balance for Steady-Flow Processes • During a steady-flow process, the total amount of mass contained within a control volume does not change with time (mCV = constant). Then the conservation of mass principle requires that the total amount of mass entering a control volume equal the total amount of mass leaving it. When dealing with steady-flow processes, we are not interested in the amount of mass that flows in or out of a device over time; instead, we are interested in the amount of mass flowing per unit time, that is, the mass flow rate It states that the total rate of mass entering a control volume is equal to the total rate of mass leaving it

8. Many engineering devices such as nozzles, diffusers, turbines, compressors,and pumps involve a single stream (only one inlet and one outlet). • For these cases, we denote the inlet state by the subscript 1 and the outlet state by the subscript 2, and drop the summation signs

9. EXAMPLE 2–1 : Water Flow through a Garden Hose Nozzle A garden hose attached with a nozzle is used to fill a 10-gal bucket. The inner diameter of the hose is 2 cm, and it reduces to 0.8 cm at the nozzle exit (Fig. 5–12). If it takes 50 s to fill the bucket with water, determine (a) the volume and mass flow rates of water through the hose, and (b) the average velocity of water at the nozzle exit. Assumptions 1 Water is an incompressible substance. 2 Flow through the hose is steady. 3 There is no waste of water by splashing. Properties We take the density of water to be 1000 kg/m3 1 kg/L. Analysis (a) Noting that 10 gal of water are discharged in 50 s, the volume and mass flow rates of water are

10. (b) The cross-sectional area of the nozzle exit is The volume flow rate through the hose and the nozzle is constant. Then the average velocity of water at the nozzle exit becomes

11. MECHANICAL ENERGY • Many fluid systems are designed to transport a fluid from one location to another at a specified flow rate, velocity, and elevation difference, and the system may generate mechanical work in a turbine or it may consume mechanical work in a pump or fan during this process. • These systems do not involve the conversion of nuclear, chemical, or thermal energy to mechanical energy. Also, they do not involve any heat transfer in any significant amount, and they operate essentially at constant temperature. • Such systems can be analyzed conveniently by considering the mechanical forms of energy only and the frictional effects that cause the mechanical energy to be lost (i.e., to be converted to thermal energy that usually cannot be used for any useful purpose). • The mechanical energy can be defined as the form of energy that can be converted to mechanical work completely and directly by an ideal mechanical device. • Kinetic and potential energies are the familiar forms of mechanical energy.

12. Therefore, the mechanical energy of a flowing fluid can be expressed on a unit-mass basis as In the absence of any changes in flow velocity and elevation, the power produced by an ideal hydraulic turbine is proportional to the pressure drop of water across the turbine.

13. Most processes encountered in practice involve only certain forms of energy, and in such cases it is more convenient to work with the simplified versions of the energy balance. For systems that involve only mechanical forms of energy and its transfer as shaft work, the conservation of energy principle can be expressed conveniently as where Emech, loss represents the conversion of mechanical energy to thermal energy due to irreversibilities such as friction. For a system in steady operation, the mechanical energy balance becomes Emech, in = Emech, out + Emech, loss

14. THE BERNOULLI EQUATION • The Bernoulli equation is an approximate relation between pressure,velocity, and elevation, and is valid in regions of steady, incompressible flow where net frictional forces are negligible ( as shown in the Figure below). Despite its simplicity, it has proven to be a very powerful tool in fluid mechanics. The Bernoulli equation is an approximate equation that is valid only in in viscid regions of flow where net viscous forces are negligibly small compared to inertial, gravitational, or pressure forces. Such regions occur outside of boundary layers and wakes.

15. Derivation of the Bernoulli Equation the Bernoulli Equation is derived from the mechanical energy equation since the we are dealing with steady flow system with out the effect of the mechanical work and the friction on the system the first terms become zero. This is the famous Bernoulli equation, which is commonly used in fluid mechanics for steady, incompressible flow along a streamline in inviscid regions of flow.

16. The Bernoulli equation can also be written between any two points on the same streamline as