1 / 11

Lecture 11. Real Heat Engines and refrigerators (Ch. 4)

Stirling heat engine Internal combustion engine (Otto cycle) Diesel engine Steam engine (Rankine cycle) Kitchen Refrigerator. Lecture 11. Real Heat Engines and refrigerators (Ch. 4). Carnot Cycle. P . 1. absorbs heat. 2. T H . 4. 3. T C . rejects heat. V .

keiji
Download Presentation

Lecture 11. Real Heat Engines and refrigerators (Ch. 4)

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Stirling heat engine Internal combustion engine (Otto cycle) Diesel engine Steam engine (Rankine cycle) Kitchen Refrigerator Lecture 11. Real Heat Engines and refrigerators (Ch. 4)

  2. Carnot Cycle P 1 absorbs heat 2 TH 4 3 TC rejects heat V - is not very practical (too slow), but operates at the maximum efficiency allowed by the Second Law. 1 – 2 isothermal expansion (in contact with TH) 2 – 3 isentropic expansion to TC 3 – 4 isothermal compression (in contact with TC) 4 – 1 isentropic compression to TH (isentropic  adiabatic+quasistatic) Efficiency of Carnot cycle for an ideal gas: (Pr. 4.5) S On the S -T diagram, the work done is the area of the loop: 3 2 entropy contained in gas The heat consumed at TH (1 – 2) is the area surrounded by the broken line: 4 1 S - entropy contained in gas TC TH T

  3. T 2 3 T2 T1 4 1 V2 V1 Stirling heat engine Stirling engine – a simple, practical heat engine using a gas as working substance. It’s more practical than Carnot, though its efficiency is pretty close to the Carnot maximum efficiency. The Stirling engine contains a fixed amount of gas which is transferred back and forth between a "cold" and and a "hot" end of a long cylinder. The "displacer piston" moves the gas between the two ends and the "power piston" changes the internal volume as the gas expands and contracts. Page 133, Pr. 4.21

  4. T 2 3 T2 T1 4 1 V2 V1 Stirling heat engine The gases used inside a Stirling engine never leave the engine. There are no exhaust valves that vent high-pressure gasses, as in a gasoline or diesel engine, and there are no explosions taking place. Because of this, Stirling engines are very quiet. The Stirling cycle uses an external heat source, which could be anything from gasoline to solar energy to the heat produced by decaying plants. Today, Stirling engines are used in some very specialized applications, like in submarines or auxiliary power generators, where quiet operation is important.

  5. T 2 3 T2 T1 4 1 V2 V1 Efficiency of Stirling Engine In the Stirling heat engine, a working substance, which may be assumed to be an ideal monatomic gas, at initial volume V1 and temperature T1 takes in “heat” at constant volume until its temperature is T2, and then expands isothermally until its volume is V2. It gives out “heat” at constant volume until its temperature is again T1 and then returns to its initial state by isothermal contraction. Calculate the efficiency and compare with a Carnot engine operating between the same two temperatures. 1-2 2-3 3-4 4-1

  6. 3 P ignition expansion work done by gas 2 compression work done on gas 4 exhaust Patm 0 1 intake/exhaust V1 V2 V Internal Combustion Engines (Otto cycle) - engines where the fuel is burned inside the engine cylinder as opposed to that where the fuel is burned outside the cylinder (e.g., the Stirling engine). More economical than ideal-gas engines because a small engine can generate a considerable power. Otto cycle. Working substance – a mixture of air and vaporized gasoline. No hot reservoir – thermal energy is produced by burning fuel. 0  1 intake (fuel+air is pulled into the cylinder by the retreating piston) 1  2 isentropic compression 2  3 isochoric heating 3  4 isentropic expansion 4  1  0 exhaust

  7. 3 P ignition expansion work done by gas 2 compression work done on gas 4 exhaust Patm 0 1 intake/exhaust V1 V2 V Otto cycle (cont.) - maximum cylinder volume - minimum cylinder volume - the compression ratio The efficiency: (Pr. 4.18)  = 1+2/f- the adiabatic exponent For typical numbers V1/V2 ~8 ,  ~ 7/5  e = 0.56, (in reality, e = 0.2 – 0.3) (even an “ideal” efficiency is smaller than the second law limit 1-T1/T3) S 3 4 S1 2 S2 1 V1 V2 V

  8. Diesel engine (Pr. 4.20)

  9. Steam engine (Rankine cycle) Boiler hot reservoir, TH P processes at P = const, Q=dH water 3 Sadi Carnot Pump 2 Boiler Turbine heat 1 Turbine work steam 4 Pump Water+steam heat V condense NOT an ideal gas! Condenser cold reservoir, TC

  10. Steam engine (Rankine cycle) Boiler hot reservoir, TH P processes at P = const, Q=dH water 3 Sadi Carnot Pump 2 Boiler Turbine heat 1 Turbine work steam 4 Pump Water+steam heat V condense Condenser cold reservoir, TC

  11. Kitchen Refrigerator A liquid with suitable characteristics (e.g., Freon) circulates through the system. The compressor pushes the liquid through the condenser coil at a high pressure (~ 10 atm). The liquid sprays through a throttling valve into the evaporation coil which is maintained by the compressor at a low pressure (~ 2 atm). condenser P processes at P = const, Q=dH 2 3 liquid throttling valve compressor 1 4 cold reservoir (fridge interior) T=50C gas liquid+gas V evaporator The enthalpies Hi can be found in tables. hot reservoir (fridge exterior) T=250C

More Related