1 / 15

Aleksander Karolczuk*, Mateusz Kowalski*, Krzysztof Kluger*, Fabian Żok**

XII International Symposium on Explosive Production of New Materials: Science, Technology, Business, and Innovations , May 25-30, 2014, Cracow. Identification of residual stress phenomena based on the hole drilling method in explosively welded steel-titanium composite.

kiral
Download Presentation

Aleksander Karolczuk*, Mateusz Kowalski*, Krzysztof Kluger*, Fabian Żok**

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. XII International Symposiumon Explosive Production of New Materials:Science, Technology, Business, and Innovations, May 25-30, 2014, Cracow Identification of residual stress phenomena based on the hole drilling method in explosively welded steel-titanium composite Aleksander Karolczuk*, Mateusz Kowalski*, Krzysztof Kluger*, Fabian Żok** The Project was financed from a Grant by National ScienceCentre (Decision No. DEC-2011/03/B/ST8/05855) ** Z.T.W Explomet S.J., Opole, Poland * Opole University of Technology

  2. The plan of presentation • Introduction • Experimental research • Residual stress calculations • Results analysis • Summary

  3. Introduction • 1) Sources of residual stresses • Manufacturing process • The heat treatment • Flattening process • 2) Consequences of residual stresses • Failure of joining process • Material strength under monotonic and fatigue loadings (negative or positive) • Stress corrosion cracking (suppressed under compressive stresses) • 3) The aim of the paper • Determination of the influence of the heat treatment on residual stress state in titanium layer of Steel-Titanium bimetal

  4. Experimental research Basic information concerning the analyzed bimetal: Flayer plate: Titanium Grade 1 (6 mm) Basic plate: S355J2+N steel (40 mm) Table 1. Chemical composition steel S355J2+N (EN 10025-2:2004) and titanium Grade 1 Table 2. Mechanical properties of the steel S355J2+N and titanium Grade 1

  5. Experimental research • 3 plates (210 x 180 x 46 mm) • without the heat treatment • 3 (210 x 180 x 46 mm) plates • after the heat treatment The heat treatment: soaking in 600oC for 90 minutes Draft of welded plate with ignition point and specimen locations.

  6. Experimental research Residual stress measurements were performed using the hole drilling method that consists of strain measurements (relaxation) around the drilled hole

  7. Experimental research Diameter: 1.5 mm (drill) Speed : 6000 rpm Two points of measurement for each plate

  8. Experimental research Strain history registered in titanium during the drilling process Measured stabilized strain values in titanium layer, registered in three directions: A, B, C

  9. Experimental research Influence of the drilling process on the measured strains Titanium plate after the heat treatment:

  10. Residual stress calculations • Residual stress calculations were performed according to: • The strain gauge manufacturer’s prescriptions (TML) • The ASTM (E837-08) prescriptions (ASTM) • Assumptions: • Uniform stress distribution – averaged residual stress state • Plane stress state • Isotropic materials

  11. Residual stress calculations Example results: TML- the specimens without the heat treatment. • Where: (1) - angle measured clockwise from direction A to 1; (P) - angle measured clockwise to A direction from detonation direction.

  12. Result analysis The mean values of the principal stress σ1 , σ2 and standard deviations calculated according to the TML and ASTM prescriptions for the specimens without and after the heat treatment.

  13. Result analysis Maximum principal stress direction and direction of detonation ? Directions of the maximum principal stresses related to detonation directions. Calculations according to the TML and ASTM methods.

  14. Result analysis 1) The tensile stresses in the titanium layer – introduced during explosive welding process 2) Compressive stresses in the titanium layer - appearing after the heat treatment are the result of different thermal expansion coefficients of welded materials

  15. Summary 1) The heat treatment changes the residual stress state in titanium. The stress state in specimen without the heat treatment is tensile and after the heat treatment is compression. 2) Direction of the maximum principal stress does not coincide with direction of detonation wave. 3) Calculation shows inhomogeneous residual stress state. The stresses change depending on the hole depth.

More Related