1 / 31

Chapter 7

Chapter 7. Noise. Noise is a term generally used to refer to any undesired disturbances that mask the received signal in a communication system. Thermal noise Shot noise. 7.1 Thermal Noise. Also known as Johnson Noise or Nyquist noise

knut
Download Presentation

Chapter 7

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Chapter 7 Noise

  2. Noise is a term generally used to refer to any undesired disturbances that mask the received signal in a communication system. • Thermal noise • Shot noise

  3. 7.1 Thermal Noise • Also known as Johnson Noise or Nyquist noise • The thermal noise current it in a resistor R may be expressed by its mean square value and is given by: • where K is Boltzmann's constant, T is the absolute temperature and B is the post-detection bandwidth.

  4. The noise current produced by these random motions of charged carriers is called “Thermal noise current” . It is given by Electrons within any resistor never remain stationary and this constitutes a randomly varying current known as thermal current. Motion due to their thermal energy.

  5. SHOT NOISE • Discrete nature of electrons causes a signal disturbance called shot noise. • Deviation of the actual number of electrons from the average number is known as shot noise. • Present for BOTH current: Signal and dark current.

  6. 7.2 Shot Noise due to Dark Current • When there is no optical power incident on the photodetector a small reverse leakage current still flows from the device terminals and this contributes to the total system noise • The shot noise due to the dark current, id is given by: where e is the charge of an electron and Id is the dark current.

  7. 7.3 Shot Noise on the Photocurrent The shot noise, is on the photocurrent Ip is given by:

  8. 7.4 Overall Receiver Noise • Figure 6.1 shows a block schematic of the front end of an optical receiver and the various noise sources associated with it. • The majority of the noise sources shown apply to both main types of optical detector (p-i-n and avalanche photodiode). • The avalanche photodiode receiver is the most complex case as it includes noise resulting from the random nature of the internal gain mechanism (dotted in Fig. 6.1).

  9. Figure 6.1

  10. 7.4.1 p-n and p-i-n Photodiode Receiver • The total shot noise iTS is given by:

  11. The thermal noise due to the load resistance RL is given by:

  12. The signal to noise ratio (SNR) for the p-n or p-i-n photodiode receiver may be obtained by summing all the noise contributions. • It is given by: where is the Photodetector Responsivity, iamp=total noise from amplifier circuit,

  13. The noise associated with the amplifier, iamp can be combined with the thermal noise from the load resistor it using the noise figure, Fn for the amplifierto give: • The expression for the SNR can now be written in the form:

  14. 7.4.2 Receiver Capacitance • The total capacitance to the front end of an optical receiver is given by: CT = Cd + Ca where Cd is the detector capacitance and Ca is the amplifier input capacitance. • Need to minimize in order to preserve the post detection bandwidth B. To increase B it is necessary to reduce RL

  15. Figure 7.4 Equalizer compensates for distortions

  16. However, a thermal noise penalty is introduced when B is increased by decreasing RL • A trade-off therefore exists between the maximum bandwidth and the level of thermal noise which may be tolerated. • This is especially important in receivers which are dominated by thermal noise.

  17. 7.4.3 Avalanche Photodiode (APD) Receiver • The internal gain mechanism in an APD increases the signal current into the amplifier and so improves the SNR. • However, the dark current and quantum noise are increased by the multiplication process and may become a limiting factor. • This is because the random gain mechanism introduces excess noise into the receiver in terms of increased shot noise above the level that would result from amplifying only the primary shot noise.

  18. Thus if the photocurrent is increased by a factor M, then the shot noise is also increased by an excess noise factor Mx, such that the total shot noise is is given by: where x is between 0.3 and 0.5 for silicon and between 0.7 and 1.0 for germanium or III-V alloy.

  19. The total SNR for the avalanche photodiode may be obtained as • This can be rewritten:

  20. It may be seen that the first term in the denominator increases with increasing M whereas the second term decreases. • For low M the combined thermal and amplifier noise term dominates and the total noise power is virtually unaffected when the signal level is increased, giving an improved SNR. • However, when M is large, the thermal and amplifier noise term becomes insignificant and the SNR decreases with increasing M at the rate of Mx.

  21. An optimum value of the multiplication factor Mop therefore exists which maximizes the SNR. • It is given by: • The variation in M, for both silicon and germanium APD is illustrated in Fig. 7.5. • This shows a plot SNR versus M with Fn equal to unity and neglecting the dark current.

  22. Figure 7.5

  23. 7.5 Receiver Structures • There are 3 basic configurations for optical receivers: • a) Low Impedance Front End • b) High Impedance Front End • c) Transimpedance Front End

  24. 7.5.1 Low Impedance Front End • Simplest and most common • Low impedance front end allows thermal noise to dominate within the receiver • Impractical for long-haul, wideband optical fiber communication systems.

  25. Low Impedance Front End Rb Ra

  26. 7.5.2 High Impedance Front End • High input impedance amplifier with large detector bias resistor to reduce thermal noise. • Degraded frequency response • Needs equalizer • Improvement in sensitivity over the low impedance front end design, but creates a heavy demand for equalization and has problems of limited dynamic range.

  27. High Impedance Front End

  28. 7.5.3 Transimpedance Front End • Overcomes the drawbacks of the high impedance front end by utilizing a low noise, high input impedance amplifier with negative feedback. • Operates as a current mode amplifier where the high input impedance is reduced by negative feedback (vout = IpRL) • Provides a far greater bandwidth without equalization than the high impedance front end. • Has a greater dynamic range. • Preferred for use in wideband optical fiber communication receivers

  29. Transimpedance Front End

  30. Exercise 1: The bandwidth was 10 MHz. The detected signal power was 2x10-12 W, and the thermal-noise power was 1.66x10-13 W at 300 K. Suppose the the photodetector is followed by an amplifier giving the power gain 10 dB and having the noise temperature 454 K. Compute the SNR.

  31. Exercise 2: A 1-Mbps NRZ link uses a 100Ω load at 300 K. The wavelength is 0.82 µm, and the desired error rate is 10-4. The PIN detector quantum efficiency is unity. Compute the optic power incident on the photodetector. Given that;

More Related