1 / 50

Properties of Sections

Properties of Sections. ERT 348 Controlled Environmental Design 1 Biosystem Engineering. Properties of Sections. Centre of gravity or Centroid Moment of Inertia Section Modulus Shear Stress Bending Stress. Centre of gravity.

kumiko
Download Presentation

Properties of Sections

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Properties of Sections ERT 348 Controlled Environmental Design 1 Biosystem Engineering

  2. Properties of Sections • Centre of gravity or Centroid • Moment of Inertia • Section Modulus • Shear Stress • Bending Stress

  3. Centre of gravity • A point which the resultant attraction of the earth eg. the weight of the object • To determine the position of centre of gravity, the following method applies: • Divide the body to several parts • Determine the area@ volume of each part • Assume the area @ volume of each part at its centre of gravity • Take moment at convenient axis to determine centre of gravity of whole body

  4. 60mm 120mm 60mm 80mm 1 3 2 Example 1: • Density=8000 kg/m3 • Thick=10 mm • Determine the position of centre of gravity x mm W1= 0.08m x 0.06m x 0.01m x 8000kg/m3 x 10 N/kg = 3.84 N W2= 0.02m x 0.12m x 0.01m x 8000kg/m3 x 10 N/kg = 1.92 N W3= 0.12m x 0.06m x 0.01m x 8000kg/m3 x 10 N/kg = 5.76 N

  5. Example 1: • Resultant, R = 3.84 +1.92 + 5.76 N = 11.52 N • Rx = 3.84 (30) + 1.92 (60+60) + 5.76 (120 + 60+30) • x = 1555/11.52 = 135 mm

  6. Centroid • Centre of gravity of an area also called as centroid.

  7. 60mm 120mm 60mm Example 1: 80mm 120mm 1 3 2 • x = 1944000/14400 = 135 mm

  8. Moment of inertia, I • Or called second moment of area, I • Measures the efficiency of that shape its resistance to bending • Moment of inertia about the x-x axis and y-y axis. y d Unit : mm4 or cm4 x x b y

  9. Rectangle at one edge Iuu= bd3/3 Ivv= db3/3 Triangle Ixx= bd3/36 Inn= db3/6 Moment of Inertia of common shapes v b d d x x u u n n v b

  10. Ixx= Iyy = πd4/64 Ixx = (BD3-bd3)/12 Iyy = (DB3-db3)/12 Moment of Inertia of common shapes y B y d x D x x x b y y

  11. Izz = Ixx + AH2 Example: b=150mm;d=100mm; H=50mm Ixx= (150 x 1003)/12 = 12.5 x 106 mm4 Izz = Ixx + AH2 = 12.5 x 106 + 15000(502) = 50 x 106 mm4 Principle of parallel axes x x H z z

  12. Example 2: • Calculate the moment of inertia of the following structural section H= 212mm 12mm 400mm 24mm 200mm

  13. Solution • Ixx of web = (12 x4003)/12= 64 x 106 mm4 • Ixx of flange = (200x243)/12= 0.23 x 106 mm4 • Ixx from principle axes xx = 0.23 x106 + AH2 AH2 = 200 x 24 x 2122 = 215.7 x 106 mm4 Ixx from x-x axis = 216 x 106 mm4 • Total Ixx = (64 + 2 x 216) x106 =496 x 106 mm4

  14. Section Modulus, Z • Second moment of area divide by distance from axis • Where c = distance from axis x-x to the top of bottom of Z. • Unit in mm3 • Example for rectangle shape: • Ixx = bd3/12, c = d/2, Zxx= Ixx/c = bd2/6

  15. Section Modulus, Z • Z = 1/y • f = M/Z = My/I • Safe allowable bending moment, Mmax = f.Z where • f = bending stress • y = distance from centroid

  16. Example 3 • A timber beam of rectangular cross section is 150mm wide and 300mm deep. The maximum allowable bending in tension and compression must not exceed 6 N/mm2. What maximum bending moment in N.mm? • Z= bd2/6 = 150 x 3002/6 = 2.25 x 106 mm3 • Mmax= f.Z = 6 x 2.25x106 = 13.5x106 Nmm2

  17. Mrc = 1/y1 x compression stress Mrt = 1/y2 x tension stress Safe bending moment = f x least Z If non-symmetrical sections y1 x x y2

  18. 120 24 235 300 x x 137 48 200 Example 4 • Figure shows an old type cast iron joist (in mm) with a tension flange of 9600 mm2, a compression flange 2880 mm2 and a web of 7200 mm2. • The safe stress in compression is 5 N/mm2 and in tension 2.5 N/mm2. What is the safe bending moment for the section? What safe uniform load will the beam carry on a 4.8m span.

  19. Solution • x =∑ay/∑a = (2880x360 + 7200x198 + 9600x24) (2880 + 7200 + 9600) = 137 mm • Total Ixx = (120x243/12 + 2880x2232)+ (24x3003/12 + 7200x612) + (200x483/12 + 960x1132) = 348.57 x 106 mm4 • Mrt = 2.5 x 348.57 x 106 = 6.36x106 Nmm • Mcr= 5.0 x 348.57 x 106 = 7.42x106 Nmm • WL/8 = 6.36x106 Nmm • W= 6.36 x 8/4.8 = 10.6 kN

  20. Elastic Shear Stress Distribution • The shear forces induced in a beam by an applied load system generate shear stresses in both the horizontal and vertical directions. • At any point in an elastic body, the shear stresses in two mutually perpendicular directions are equal to each other in magnitude.

  21. Shear Stress

  22. 50mm x x 200mm Example 5: Elastic Shear Stress • The rectangular beam shown in Figure is subject to a vertical shear force of 3.0 kN. • Determine the shear stress distribution throughout the depth of the section. A y y

  23. Solution: 3 y=50mm 4 y=25mm 1 5 y=0mm 2

  24. Answer:

  25. Answer: • Average τ = V/A = 3 x 103/(50x200) = 0.3 N/mm2 • Maximum = 1.5 V/A = 1.5x0.3 = 0.45 N/mm2

  26. Bending Stress Distribution • f=σ= bending stress = My/I

  27. 50mm x x 200mm M= 2.0 kNm

  28. UFO lawat Menara KL?

  29. Material Properties Concrete

  30. Concrete • Concrete compressive strength: fcu • C30,C35,C40,C45 and C50 • Where the number represent compressive strength in N/mm2

  31. Modulus Elasticity, E Es(Modulus Elasticity of steel reinforcement) = 200 kN/mm2

  32. Poisson ratio υc • Refer to Clause 2.4.2.4 BS 8110 • The value = 0.2

  33. Steel Reinforcement Strength: fy • Refer to Clause 3.1.7.4 BS 8110 (Table 3.1) • fy= 250 N/mm2 for hot rolled mild steel (MS) • fy= 460 N/mm2 for hot rolled or cold worked high yield steel (HYS)

  34. Material Properties Steel

  35. Design strength, py

  36. Modulus Elasticity, E • Modulus elasticity, E = 205 000 N/mm2 Poisson ratio υc • The value = 0.3 Shear Modulus,G • G=E/[2(1+υ)] = 78.85 x103 N/mm2

  37. Section classification • Refer to Table 11 & Table 12 BS5950-1:2000 Clause 3.5 • Class 1 - Plastic Sections • Class 2 - Compact Sections • Class 3 - Semi-compact Sections • Class 4 - Slender Sections

  38. Aspect ratio • ε=(275/py)0.5

  39. Types of sections • I sections • H sections • Rectangular Hollow Sections (RHS) • Circular Hollow Sections (CHS) • Angles (L shape or C shapes)

  40. Types of sections

  41. Material Properties Timber

  42. Moisture content • m1=mass before drying • m2=mass after drying • Unit in % • The strength of timber is based on its moisture content. • In MS 544, the moisture content – 19% • >19% - moisture • <19% - dry

  43. Material Properties • Elastic Modulus E = 4600 – 18000 N/mm2 • Poisson’s Ratio υ = 0.3

  44. Grade of timber • Timber can be graded by • Visual Inspection • Machine strength grading • 3 grade only • Select • Standard • Common Less defect

  45. Group of timber • We have Group • A • B • C • D Lower strength

  46. Defects by nature

  47. Defects in timber • In addition to the defects indicated in Figure 7.1 there are a number of naturally occurring • defects in timber. The most common and familiar of such defects is a knot

  48. Typical sawing pattern

  49. Reference to design • MS 544 : Pt.1-Pt.11 : 2001 - Code of Practice for Structural Use of Timber

  50. Continue structure design...

More Related