1 / 22

Wireless Telemetry System for Solar Vehicle

School of Electrical and Computer Engineering. Wireless Telemetry System for Solar Vehicle. Scott Cowan Elliot Hernandez Tung Le April 25, 2011. Project Overview. Source: http://www.ece.gatech.edu/academic/courses/ece4007/10fall/ECE4007L01/ws1/files/sjt_final_presentation.ppt.

mahala
Download Presentation

Wireless Telemetry System for Solar Vehicle

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. School of Electrical and Computer Engineering Wireless Telemetry System for Solar Vehicle Scott Cowan Elliot Hernandez Tung Le April 25, 2011

  2. Project Overview Source: http://www.ece.gatech.edu/academic/courses/ece4007/10fall/ECE4007L01/ws1/files/sjt_final_presentation.ppt

  3. Design Overview Solar Car Current Transmitter Data Storage Chase Car Speed USB USB SBC Temperature SPI DIO Laptop RS-485/RS-232 USB Voltage Battery Mgmt. Motor Ctrl. MPPT HMI GPS

  4. Design Problems & Solutions Problem: Programming C code for TCP/IP protocol for file sync Solution: Switched to C++ to use FTP protocol Problem: Using hardware SPI for the ADC converter Solution: Bit-bang(software based) using the SPI bus

  5. Hardware Problems & Solutions Problem: PCB errors discovered too late to correct Solution: Used wires to bypass incorrect traces; corrected schematics and PCB files for future reference

  6. Outside View of Telemetry Box Comm. Jacks Input Terminals USB Ports

  7. Inside View of Telemetry Box Flash Drive PCB SBC USB Hub

  8. Sensor Testing Methods

  9. Voltage Inputs • Telemetry box accepts 0-5 Vdc signals • Signal conditioner used to convert high voltage signals to low voltage signals at point of origin • Three of six voltage inputs scaled for 0-120 Vdc • Remaining voltage inputs scaled for 0-5 Vdc

  10. Testing High Voltage Input • Available power supply limited to 50 V • Inputted 0-50 Vdc into signal conditioner in 5 V increments • Compared readings from SBC to Fluke 199C Scopemeter

  11. Testing Low Voltage Inputs • Input 0-5 Vdc into telemetry box in 0.5 V increments • Compared readings from SBC to Fluke 199C Scopemeter

  12. Voltage Measurement Results • Percentage error decreases as DC input increases

  13. Current Inputs • Telemetry box accepts 10 current inputs with a range of ±140 A • To simulate high currents, 10 loops of wire were passed through current sensor

  14. Testing Current Inputs • Looped wire connected in series with 12 V battery and 1 Ω, 225 W variable resistor • Resistance varied to give various currents • Reversed wiring to give negative values • Current measured using Fluke 199C Scopemeter with 80i-110s clamp-on ammeter • Ammeter readings multiplied by 10 and compared to SBC readings

  15. Current (I) Sensor Results • Current sensor is capable of bi-directionality

  16. Temperature Inputs • Readings from temperature are incorrect • Error occurred after soldering to PCB • Cause of error remains unknown

  17. GPS Output • $GPRMC,201740.394,V,,,,,,,101110,,,N*43 • $GPRMC,201741.394,V,,,,,,,101110,,,N*42 • Note: GPS is in the NMEA 0183 format, where the output is $GPAAM,A,A,CR,N,WPTNME*32

  18. Future Testing • RS-485 To RS-232 converter • Speed sensor input comparison to tachometer

  19. Remote Laptop Program • C++ program that runs FTP protocol • Can be used on any OS • Updates the file from the SBC to host computer every 10 seconds • Re-establish the connection when WIFI signal is broken • CSV file readable using text editor, Excel, Matlab, etc…

  20. Project Costs

  21. Future Improvements • Add LED status sensors to enclosing • Upgrade SBC to newer hardware • Increase in computation • lower power usage • Reduce compatibility issues • Use hardware interrupts for RPM calculations • Correct discovered errors in PCB

  22. Questions?

More Related