F1020/F1031 COMPUTER HARDWARE MEMORY

1. F1020/F1031 COMPUTER HARDWAREMEMORY

2. Read-only Memory (ROM) • Basic instructions for booting the computer and loading the operating system are stored in ROM • Read-only memory (ROM) chips are located on the motherboard. • ROM chips contain instructions that can be directly accessed by the CPU. Basic instructions for booting the computer and loading the operating system are stored in ROM. • ROM chips retain their contents even when the computer is powered down. The contents cannot be erased or changed by normal means. NOTE: ROM is sometimes called firmware. This is misleading because firmware is actually the software that is stored in a ROM chip.

4. Random-access Memory (RAM) • Temporary storage for data and programs that are being accessed by the CPU • Volatile memory, which means that the contents are erased when the computer is powered off • More RAM means more capacity to hold and process large programs and files, as well as enhance system performance. • Types of RAM: • Dynamic Random Access Memory (DRAM) • Static Random Access Memory (SRAM) • Fast Page Mode DRAM (FPM Memory) • Extended Data Out RAM (EDO Memory) • Synchronous DRAM (SDRAM) • Double Data Rate SDRAM (DDR SDRAM) • Double Data Rate 2 SDRAM (DDR2 SDRAM) • RAMBus DRAM (RDRAM)

5. Dynamic Random Access Memory (DRAM) is a memory chip that is used as main memory. DRAM must be constantly refreshed with pulses of electricity in order to maintain the data stored within a chip. • Static Random Access Memory (SRAM) is a memory chip that is used as cache memory. SRAM is much faster than DRAM and does not have to be refreshed as often. • Fast Page Mode DRAM (FPM Memory) is memory that supports paging. Paging enables faster access to the data than regular DRAM. Most 486 and Pentium systems from 1995 and earlier use FPM memory.

6. Extended Data Out RAM (EDO Memory) is memory that overlaps consecutive data accesses. This speeds up the access time to retrieve data from memory, because the CPU does not have to wait fro one data access cycle to end before another data access cycle begins. • Synchronous DRAM (SDRAM) is DRAM that operates in synchronization with the memory bus. The memory bus is the data path between the CPU and the main memory.

7. Double Data Rate SDRAM (DDR SDRAM) is memory that transfers data twice as fast a SDRAM. DDR SDRAM increases performance by transferring data twice per cycle. • Double Data Rate 2 SDRAM (DDR2 SDRAM) is faster than DDR SDRAM memory. DDR2 SDRAM improves performance over DDR SDRAM by decreasing noise and crosstalk between the signal wires. • RAMBus DRAM (RDRAM) is a memory chip that was developed to communicate at very high rates of speed. RDRAM chips are not commonly used.

8. Memory Modules • Dual Inline Package (DIP) is an individual memory chip. A DIP had dual rows of pins used to attach it to the motherboard. • Single Inline Memory Module (SIMM) is a small circuit board that holds several memory chips. SIMMs have 30-pin and 72-pin configurations. • Dual Inline Memory Module (DIMM) is a circuit board that holds SDRAM, DDR SDRAM, and DDR2 SDRAM chips. There are 168-pin SDRAM DIMMs, 184-pin DDR DIMMs, and 240-pin DDR2 DIMMs.

9. RAM Bus Inline Memory Module (RIMM) is a circuit board that holds RDRAM chips. A typical RIMM has a 184-pin configuration. Notes: Memory modules can be single-sided or double-sided. Single-sided memory modules only contain RAM on one side of the module. Double-sided memory modules contain RAM on both sides of the module

10. Cache and Error Checking Cache • SRAM is used as cache memory to store the most frequently used data. • SRAM provides the processor with faster access to the data than retrieving it from the slower DRAM, or main memory. Error Checking • Memory errors occur when the data is not stored correctly in the RAM chips. • The computer uses different methods to detect and correct data errors in memory

11. 30/32 pin 72 pin 168 pin