1 / 64

Troubleshooting HT

Troubleshooting HT. Training Course Daikin Altherma HT + Flex Type ( S-HTF01-004 ). CAUTION!!!. When power is off, there still can be high voltage on the top surface of the capacitors!!!. Troubleshooting (1). Opening unit for servicing General symptoms Indoor unit DHW tank Error codes

mhuang
Download Presentation

Troubleshooting HT

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Troubleshooting HT Training Course Daikin Altherma HT + Flex Type (S-HTF01-004)

  2. CAUTION!!! When power is off, there still can be high voltage on the top surface of the capacitors!!!

  3. Troubleshooting (1) • Opening unit for servicing • General symptoms • Indoor unit • DHW tank • Error codes • Inspection on remocon • Service mode 40 on remocon • Service PCB outdoor unit • Monitoring mode outdoor unit

  4. Troubleshooting (2) • Vacuuming/recovering R410A • Pump down R410A • Vacuuming/recovering R134a • Check 3-way valve • Check fan motor • Spare part PCB

  5. Opening unit for servicing (1) To faciliate access to: • Air purge valve • Thermal cut-out • 3-way valve • Thermistors • Field wiring duct • …

  6. Opening unit for servicing (2) In combination with removing top panel: To faciliate access to: • manometer • Pressure relief valve • …

  7. Opening unit for servicing (3) Disconnect all field wiring

  8. General Symptoms – Indoor Unit

  9. General Symptoms – Indoor Unit

  10. General Symptoms – Indoor Unit

  11. General Symptoms – Indoor Unit

  12. General Symptoms – Indoor Unit

  13. General Symptoms – DHW tank

  14. General Symptoms – DHW UK tank (1)

  15. General Symptoms – DHW UK tank (2)

  16. Error codes For detailed overview -> see error flow chart in appendix To reset the safety (in case problem is solved), push In case of “UA” error, wait till initialisation between outdoor unit and indoor unit is finished (after power ON, wait at least 12 minutes)

  17. Outdoor Unit Error Codes (1) • A9: expansion valve R410A error • E1: compressor PCB error (R410A) • E3: high pressure error (S1PH) • E4: low pressure error (B1PL) • E5: compressor lock error (R410A) • E9: expansion valve error R410A • F3: discharge temperature error R410A • J3: discharge thermistor error R410A • J5: suction pipe thermistor R410A • JA: high pressure sensor R410A

  18. Outdoor Unit Error Codes (2) • JC: low pressure sensor R410A • L1: compressor inverter PCB error (R410A) • L4: fin thermistor outdoor inverter PCB error • L5: compressor inverter PCB error (R410A) • L8: compressor inverter PCB error (R410A) • L9: compressor inverter PCB error (R410A) • LC: communication error • U2: power supply failure • U4: transmission failure • U5: transmission failure

  19. Outdoor Unit Error Codes (3) • UF: transmission failure • UA: # of units • UH: malfunction of system: address error

  20. Indoor Unit Error Codes (1) • A1-00: EEPROM error (main PCB A1P) • A6-00: pump error or other water system error • A9-00: expansion valve R410A error • AJ-00: capacity error • C1-00: communication error • C4-00: liquid thermistor error R410A (R3T) • C5-00: tank thermistor error (R2T) • C9-00: return water thermistor error (R4T) • CA-00: leaving water thermistor error (R5T) • E1-03: compressor PCB error (R134a)

  21. Indoor Unit Error Codes (2) • E3-01: high pressure error (S1PH) (R410A) • E3-12: high pressure error (S1PH) (R134a) • E4-06: low pressure error (B1PL) (R134a) • E5-06: compressor lock error • E9-17: expansion valve error R134a (K2E) • F3-19: discharge temperature error R134a • J3-46: discharge thermistor error R134a (R6T) • J5-11: liquid thermistor R134a (R7T) • JA-16: high pressure sensor R134a (B1PH) • JC-16: low pressure sensor R134a (B1PL)

  22. Indoor Unit Error Codes (3) • L1-30: compressor inverter PCB error (R134a) • L4-08: fin thermistor error (R8T ~ inverter PCB) • L5-13: compressor inverter PCB error (R134a) • L8-10: compressor inverter PCB error (R134a) • L9-09: compressor inverter PCB error (R134a) • LC-29: communication error (cascade) • PJ-11: combination error • U2-20/21: power supply failure (cascade) • U4-00: communication error • U4-04: communication error (cascade)

  23. Indoor Unit Error Codes (4) • U5-00: remocon error • UF-06: communication error (cascade) • UF-10: communication error • UA-13: communication error with outdoor unit • UH-00: address error • LH-02: converter error • P1-06: main compressor PCB error

  24. Remote Controller Error Codes • CJ: remocon thermostat thermistor

  25. Error codes CODE DESCRIPTION POSSIBLE CAUSE CORRECTIVE ACTION A1 EEPROM error (main pcb A1P) EEPROM fail Try power OFF/ON Subcode 0 IU Broken pcb Replace pcb Subcode: When Indoor Unit error code IU: Indoor Unit error code OU: Outdoor Unit error code Remocom: Remote Controller error

  26. Inspection on remocon

  27. Service mode 40 - last 5 errors - on remocon

  28. Monitor mode Outdoor Unit

  29. Service PCB

  30. Service PCB Outdoor Unit 8 leds (H1P ~ H8P) 2 dipswitches (do not change) 5 buttons (BS1 ~ BS5)

  31. H*P leds • During initialisation: Multi led H8P blinks • In normal status: Indication led H3P is ON

  32. Vacuuming/Recovering R410A circuit Setting 2-21 1) Press BS1 mode button for 5 seconds • H1P led is ON (= setting mode 2) 2) Press BS2 set button 21 times (= recovery/vacuuming operation) H8P 16 4 1 Binary code 21

  33. Vacuuming/Recovering R410A circuit Setting 2-21 3) Press BS3 return button to enter 4) Press BS2 set button to set function to ON 5) Press BS3 return button to define setting 6) Press BS3 button to activate vacuuming/recovering operation

  34. Vacuuming/Recovering R410A circuit Setting 2-21

  35. Vacuuming/Recovering R410A circuit Setting 2-21 -> Vacuum the system with a vacuum pump / Recovery the system with a refrigerant reclaimer -> When finished, press BS1 mode button to reset

  36. Pump down R410A circuit Setting 2-61 1) Close liquid stop valve (gas stop valve stays open) 2) Press BS1 mode button for 5 seconds • H1P led is ON (= setting mode 2) 3) Press BS2 set button 61 times (= pump down operation) 8 32 16 4 1 Binary code 61

  37. Pump down R410A circuit Setting 2-61 4) Press BS3 return button to enter 5) Press BS2 set button to set function to ON 6) Press BS3 return button to define setting 7) Press BS3 button to activate pump down operation

  38. Pump down R410A circuit Setting 2-61 -> Compressor and fan will start operating automatically. -> During operation, the led’s are showing the progress as shown as the figure below: -> If step 5 is reached (pressure drops below 3 bar) or if operation stops (after 30 minutes), close the gas stop valve

  39. Pump down R410A circuit Setting 2-61 ONLY WHEN PIPING LENGTH IS BELOW 10M!!!

  40. Vacuuming/recovering R134a Setting [E-00] • Setting [E-00] must be acitvated before!!! • Will force the unit into thermo OFF and will open the expansion valve of the indoor unit R134a circuit so full vacuuming is possible • Disabled (0) (default) or enabled (1) Do not forget to restore field setting [E-00] back to (0), when vacuuming/recovering is finished

  41. Check 3-way valve DHW SH 220V 0V 0V 220V 220V 220V

  42. Install 3-way valve (adjusting after wrong installation) Sleeve down Space heating From indoor Open To DHW Blocked

  43. Attention points 3-way valve (after installation)

  44. Check fan motor

  45. Spare part PCB

  46. Compressor inspection - CAUTIONS • Never perform the inspection when the system is under a vacuum • Never perform the inspection when power is applied to the system

  47. Insulation resistance inspection - Procedure • Remove all wiring from compressor terminals to isolate the compressor • Make sure the terminals and the compressor ground location are properly cleaned and free of oxidation • Switch the megger to 500 or 1000V, the set voltage should always be higher then the operational voltage of the compressor

More Related