1 / 11

Setup Ethernet & PPP client on Laptop computer

Setup Ethernet & PPP client on Laptop computer. Presented by: Xuewu Cai Jianfang Wang. Project Purpose. 1. Setup PCMCIA controller , let it probe correctly PCMCIA card attached on it. 2. Set up Ethernet interface, including assign IP address, subnet mask to it.

oberon
Download Presentation

Setup Ethernet & PPP client on Laptop computer

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Setup Ethernet & PPP client on Laptop computer Presented by: Xuewu Cai Jianfang Wang

  2. Project Purpose • 1. Setup PCMCIA controller , let it probe correctly PCMCIA card attached on it. • 2. Set up Ethernet interface, including assign IP address, subnet mask to it. • 3. Setup PPP dialup client , write a script program using AT command set to dialup. Configure pppd to setup PPP interface.

  3. Cont’d (purpose) • 4. Choose proper route for 2 interfaces above including default router, local subnet route,etc .loopback interface route.

  4. Configureation Steps • Ethernet card, Modem,etc are installed onto laptop computer by PCMCIA controller as PCMCIA card. • PCMCIA card can include ethernet card, modem, memory card, serial card,SCSI&IDE card,etc. • PCMCIA support should be compiled into Linux kernel

  5. Cont’d (Steps) • Put system reserved I/O port, memory into /etc/pcmcia/config.opts, in out project,parameter is : • I/O Range: 3E0-3E1 • Memory Range: D8000-DBFFF • Current release contain drivers for all the devices. All these drives are loaded as modules on linux. • When system(socket driver) detect the availability of pcmcia card in socket slots, it will run corresponding shell program under /etc/pcmcia to bring up interfaces. • Ethernet card will run “network”, modem will run “serial”,etc

  6. Configure Ethernet card • Set network configuration parameter into /etc/pcmcia/network.opts • The details of setting: • IP address : 130.85.100.254 • Subnet mask: 255.255.255.0

  7. Cont’d (Ethernet Card) • DNS1: 130.85.1.5 • DNS2: 130.85.1.3 • default router: 130.85.100.1 • local subnet route: 130.85.100.0 0.0.0.0

  8. Ifconfig output • lo        Link encap:Local Loopback           inet addr:127.0.0.1  Bcast:127.255.255.255 Mask:255.0.0.0           UP BROADCAST LOOPBACK RUNNING  MTU:3584  Metric:1           RX packets:18 errors:0 dropped:0 overruns:0 frame:0           TX packets:18 errors:0 dropped:0 overruns:0 carrier:0 coll:0 • eth0      Link encap:Ethernet  HWaddr 00:E0:98:01:1C:87           inet addr:130.85.100.254  Bcast:130.85.100.255  Mask:255.255.255.0           UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1           RX packets:14 errors:0 dropped:0 overruns:0 frame:0           TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 coll:0           Interrupt:5 Base address:0x300

  9. Configure PPP client • Choose chat as dialup tools • Write a piece of chat script as following:' ' ATZ OK ATDTtelno CONNECT ' ' username < user account... passwd <user password... PPP 1Save it as script.dialup • Run pppd, choosing options likepppd connect "chat -f script.dialup" /dev/cua1 115200 -detach modem noipdefault defaultroute

  10. Cont’d (PPP client) • Set proper route for PPP using route command. • What to disconnect PPP connection? Use command like:kill `cat /var/run/ppp0.pid /dev/console

  11. Ifconfig output • lo Link encap:Local Loopback inet addr:127.0.0.1 Bcast:127.255.255.255 Mask:255.0.0.0 UP BROADCAST LOOPBACK RUNNING MTU:3584 Metric:1 RX packets:18 errors:0 dropped:0 overruns:0 frame:0 TX packets:18 errors:0 dropped:0 overruns:0 carrier:0 coll:0 • eth0 Link encap:Ethernet HWaddr 00:E0:98:01:1C:87 inet addr:130.85.100.254 Bcast:130.85.100.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 coll:0 Interrupt:5 Base address:0x300 • ppp0 Link encap:Point-to-Point Protocol inet addr:130.85.97.34 P-t-P:130.85.2.203 Mask:255.255.255.0 UP POINTOPOINT RUNNING MTU:1500 Metric:1 RX packets:24 errors:0 dropped:0 overruns:0 frame:0 TX packets:7 errors:0 dropped:0 overruns:0 carrier:0 coll:0

More Related