1 / 22

Chapter 30

Chapter 30. Mutual Inductance. Consider a changing current in coil 1 We know that B 1 = m 0 i 1 N 1 And if i 1 is changing with time, dB 1 /dt= m 0 N 1 d(i 1 )/dt But a changing B-field across coil 2 will initiate an EMF 2 such that EMF 2 =-N 2 A 2 dB1/dt

oliver
Download Presentation

Chapter 30

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Chapter 30

  2. Mutual Inductance Consider a changing current in coil 1 We know that B1=m0i1N1 And if i1 is changing with time, dB1/dt=m0N1 d(i1)/dt But a changing B-field across coil 2 will initiate an EMF2 such that EMF2=-N2A2 dB1/dt Since dB1/dt is proportional to di1/dt then the Where M is the mutual inductance which is based on the sizes of the coils, and the number of turns

  3. Mutual-mutual Inductance But it could be that the changes are happening in coil 2. Then It turns out that this value of M is identical to the previously discussed M so

  4. My favorite unit—the henry • The Henry (H) is the unit of inductance • Equivalent to: • 1H=1 Wb/A = 1 V*s/A = 1 W*s = 1 J/A2 • H is large unit; typically we use small units such as mH and mH.

  5. Self Inductance • But a coil of wire with a changing current can produce an EMF within itself. • This EMF will oppose whatever is causing the changing current • So a coil of wire takes on a special name called the inductor

  6. Inductor Electrical symbol • Definition of inductance is the magnetic flux per current (L) • For an N-turn solenoid, L is • L= NF/I • N turns= (n turns/length)*(l length) • The near center solution of inductance depends only on geometry

  7. i (increasing) i (decreasing) High potential Low potential VL acts like a VL acts like a Low potential High potential Inductor Electrical symbol Again, the EMF acts to oppose the change in current

  8. R A S B V L RL Circuits • Initially, S is open so at t=0, i=0 in the resistor, and the current through the inductor is 0. • Recall that i=dq/dt

  9. Switch to A Initially, the inductor acts against the changing current but after a long time, it behaves like a wire R A S H i B V L L

  10. R A S B V L Voltage across the resistor and inductor Potential across resistor, VR Potential across capacitor, VC At t=0, VL=V and VR=0 At t=∞, VL=0 and VR=V

  11. L/R—Another time constant • L/R is called the “time constant” of the circuit • L/R has units of time (seconds) and represents the time it takes for the current in the circuit to reach 63% of its maximum value • When L/R=t, then the exponent is -1 or e-1 • tL=L/R

  12. Switch to B • The current is at a steady-state value of i0 at t=0 R A S B V L

  13. Energy Considerations Rate at which energy is supplied from battery Rate at which energy is stored in the magnetic field of the inductor Energy of the magnetic field, UB

  14. Energy Density, u • Consider a solenoid of area A and length, l Energy stored at any point in a magnetic field Energy stored at any point in a magnetic field

  15. L-C Oscillator – The Heart of Everything C L If the capacitor has a total charge, Q

  16. Perpetual Motion?

  17. Starting Points Charge q Current i t The phase angle, f, will determine when the maximum occurs w.r.t t=0 The curves above show what happens if the current is 0 at t=0

  18. Energy considerations • A quick and dirty way to solve for i at any time t in terms of Q & q • At t=0, the total energy in the circuit is the energy stored in the capacitor, Q2/2C • At time t, the energy is shared between the capacitor and inductor • (q2/2C)+(1/2 Li2) • Q2/2C= (q2/2C)+(1/2 Li2)

  19. Oscillators is oscillators is oscillators

  20. Give me an “R”! Consider adding a resistor, R to the circuit The resistor dissipates the energy. For example, consider a child on a swing. His/her father pushes the child and gets the child swinging. In a perfect system, the child will continue swinging forever. The resistor provides the same action as if the child let their feet drag on the ground. The amplitude of the child’s swing becomes smaller and smaller until the child stops. The current in the LRC circuit oscillates with smaller and smaller amplitudes until there is no more current

  21. Mathematically When oscillation stops due to R, critically damped If R is small, underdamped Very large values of R, overdamped

  22. Why didn’t I use a voltage source? • The practical applications of the LC, LR, and LRC circuits depend on using a sinusoidally varying voltage source: • An AC voltage source

More Related