1 / 21

Compact log splitters

Compact log splitters. Splitting force Engine Pump Log Capacity Hydraulic Tank Capacity Cycle Time Operation Log Cradles Warranty . 8 Tons 123cc OHV Engine Single stage 7.4LPM @ 3500 RPM Up to 19“ 1.5 Gallons 24 Seconds Horizontal Included 2-Year Limited.

onawa
Download Presentation

Compact log splitters

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Compact log splitters

  2. Splitting force Engine Pump Log Capacity Hydraulic Tank Capacity Cycle Time Operation Log Cradles Warranty 8 Tons 123cc OHV Engine Single stage 7.4LPM @ 3500 RPM Up to 19“ 1.5 Gallons 24 Seconds Horizontal Included 2-Year Limited Specifications

  3. Using the Log splitter • Remove the locking pin. • Slide the cylinder back until the trunnions rest in their cradle, pressing against the safety switch. • Re-install the locking pin in its hole. Locking pin Cylinder extended to the operating position

  4. NOTE: the engine will not run unless the safety switch is depressed. Locking pin cradle Trunnion Safety switch Trunnions pushing in the safety switch

  5. Storing the log splitter • For storage, run it out of fuel. • Retract the cylinder over the beam. • The unit can be stored in the vertical or horizontal position.

  6. Pump • Please note that the pump is rated in LPM (Liters Per Minute). • The flow rate of this pump 2 GPM, this volume is so low that a 10% change in flow would still be about 2 GPM. • Therefore it is recommended that all flow tests be done using LPM as a measurement scale.

  7. Valve • This log splitter uses the same valve assembly as the bigger MTD log splitters. Valve assembly Grab handle

  8. Oil Change • To change the oil, remove the drain plug. NOTE: Replace the aluminum gasket before installing the drain plug. Aluminum gasket Drain plug

  9. Air filter • Access the air filter by removing the thumb screw and opening the filter cover. • This engine has a foam pre-cleaner and a paper air filter like the rest of he MTD engines. Cover Thumb screw

  10. Adding hydraulic fluid Vent Oil fill plug Use a SAE 10 AW oil or Dextron III (About 1.75 gal) Cycle the cylinder 12 times to bleed the system

  11. Changing the belt • First, remove the bottom cover. NOTE: the log splitter will stand on end for easy access to the belt. • Slip the belt off of the spring loaded idler. Idlerspring Spring loaded idler

  12. Testing the hydraulics Before testing the hydraulics: • Make sure reservoir is full with the proper fluid • The beam is oiled • Check the air filter and oil of the engine • Using a tach, set the engine to 3500 rpm • Check the belt condition and tension

  13. Equipment needed Extra length of hose Flow gauge Various adapters

  14. Install the flow gauge at the pump • Install the flow gauge between the pump and the inlet port of the control valve

  15. Testing the pump • Run the log splitter until the fluid is warm. • Cycle the log splitter a dozen times to bleed the air out of the fluid.

  16. Read the flow gauge LPM GPM Using the LPM side of the flow gauge will give a more accurate reading. It should read at least 7lpm. Start test with snubber valve open.

  17. Testing the pump • Slowly close the snubber valve while watching gauges. NOTE: the relief valve is in the main valve assembly. When closing the snubber valve do not build pressure above 3200psi to prevent damage to the pump. • Pressure should increase, while flow stays the same. NOTE: this is a single stage pump without a bypass. Flow gauge Pressure gauge

  18. Interpreting the results • The flow should remain constant (within 1lpm) @ 3500 rpm, regardless of pressure. • If flow drops, but engine rpm remains constant, the pump is bad. • If pressure does not build, check for a slipping belt, pulley or dropping engine rpm.

  19. Testing the valve assembly • Install the flow gauge between the valve assembly and the return port of the cylinder. Flow NOTE: The extend port of the control valve is mounted to a nipple on the cylinder. Testing of the extend port would require removal of the valve.

  20. Testing the valve • Extend and retract the cylinder. • Note the reading of the flow gauge while the cylinder is retracting. • Build pressure in the valve by slowly closing the snubber valve while watching the flow gauge. • Close the snubber valve completely to check the relief valve operation.

  21. Interpreting the results • If the flow drops when pressure builds, the valve is leaking internally. • If the flow remains constant, and pressure can be built up, then the cylinder is leaking internally. • If the pump and cylinder test normal the problem is probably in the control valve. • If the relief valve is releasing below 1700psi, the valve assembly should be replaced.

More Related