1 / 11

Spallation Neutron Source Low-Level RF Control System

EPICS Meeting 2005, SLAC. Spallation Neutron Source Low-Level RF Control System. Kay-Uwe Kasemir, Mark Champion. April 2005. SNS Linac LLRF. RF Reference Line, Timing System. Klystron. Cavity. LLRF. [mW]. [MW]. Fwd. Ref.

owen
Download Presentation

Spallation Neutron Source Low-Level RF Control System

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. EPICS Meeting 2005, SLAC Spallation Neutron SourceLow-Level RF Control System Kay-Uwe Kasemir, Mark Champion April 2005

  2. SNS Linac LLRF RF Reference Line, Timing System Klystron Cavity LLRF [mW] [MW] Fwd Ref • LLRF produces the Milliwatt-level “RF drive”: Pulsed @ 60Hz, 1.3ms • 96 cavities of various types,15 warm (RFQ, MEBT, DTL, CCL), rest superconducting (SCL);some cavities at 402.5, some at 805 MHz. • RF Reference, forward, reflected and cavity data is down-converted to50 MHz, then sampled at 40 MHz,resulting in data streams of I, Q, -I, -Q, … (re. & im. of complex data) • At 40 MHz, a fully digital control system (FPGA & CPU) computes output data stream which gets up-converted to 402.5 resp. 805 MHz.

  3. VXI Crate with MVME2100 CPU SNS Utility board Time of day, events, etc.via SNS real-time data link SNS Timing board TTL timing pulses “High Power Protection Module” Monitors power levels,arc detectors, …for fast shutdown “Field Control Module” 40MHz FPGA-based control loop SC Linac uses IOCs with 2xHPM, 2xFCM.Total of about 55 IOCs. We use VXI as if it was VME No need for VXI “slot-based” addressing 8-bit VME instead of 16-bit VXI interrupt vectors. VME CPU on extender board cheaper than VXI slot-zero controller. LLRF Hardware

  4. HPM - High Power Protection Module • Fast RF Shutdown • Monitors 8 RF channels,-50…+10 dBm (10nW…10mW),for the duration of the RF gate. • Per-channel threshold and time limit.Trips when RF above threshold longer than time limit. • Monitors 14 arc detector inputs. • Computed/software interlocks. • Everything can be enabled/disabled,except one hardware input for “Vacuum OK” signal. • 2 history buffers capture 2ms of data (2s resolution).User selectable for any RF channel, arc detector,or misc. other internals of the HPM. • Trip information is sent to the FCM via redundant VXI backplane lines. FCM then cuts the RF drive.

  5. LBNL MEBT LLRF Control Box(Larry Doolittle, http://recycle.lbl.gov/~ldoolitt/llrf ) “nanoEngine”check-card computer,runs Linux & EPICS R3.14. Xilinx Spartan FPGAXC2S150for 40MHz control loop. Mini-Circuits components. OK, but at its limit:6kB of history buffer,no floating-point CPU. FCM Ancestor: SNS “Generation 1 & 2” LLRF

  6. VXI Carrier Board Analog Front End Replaces Mini-Circuits. Digital Front End From SNS BPMs Xilinx Virtex II XC2V1500 (2xI/O, 4xlogic cells over gen. 1,2) RF Output AFE & RFOspecific to 805vs. 402.5 MHz Firmware (VHDL)translated fromGen. 1/2 LLRF(Verilog),then extended. FCM - “Generation 3”

  7. FCM Firmware vs. CPU Software • FCM Firmware • 40 Mhz PI controller. • History Buffers: 5 x 512 x 16 bit x {I, Q}with configurable zoom & pan. • Feed-Forward Buffer: 4096 x 8bit x {I,Q},200ns or 400ns granularity. • CPU Software • ‘Arm’ waveform updates synchronously with SNS event link. • Decode raw buffer data intoI, Q, Phase, Amplitude waveforms. • Resonance Error Calculation. • Adaptive Feed-Forward. • Automation.

  8. Example SNS LLRF Screen for one cavity Cavity amplitude & phase controls Calls up Auto-Run sequencer page Calls up FCM “expert” pages including Adaptive FeedForward controls

  9. The Auto-Run Sequence simplifiesturn on of an RF station • Ramp RF drive level open-loop in frequency-tracking mode until desired cavity gradient is reached. • Warmup the cavity in frequency-tracking mode until acceptable resonance error is reached. • Close the feedback loop after setting loop phase. • Monitor the status of the HPRF system throughout the sequence.

  10. Adaptive FeedForward Beam Compensation Fig. 1 Beam loading in DTL6 with ~40 us, 20 mA beam induced error of 2.7% and 2 deg in amplitude and phase. Fig. 2 Beam loading eliminated by means of Adaptive FeedForward.

  11. SNS LLRF Status • Installation of IOCs completed,maybe 80% of the cavities connected. • Working on improved • Interlocks • Closed loop for superconducting section • Adaptive feed forward • Firmware:Larry Doolittle wrote new firmware in Verilog which synthesizes for Generation 1, 2 & 3 hardware.Debug this ‘portable’ firmware and use it,or stay with proven ‘FCM-only’ firmware?

More Related