1 / 34

DATA ACQUISTION AND SIGNAL PROCESSING

DATA ACQUISTION AND SIGNAL PROCESSING. Lecture Introduction to Opamps & Multisim. Dr. Tayab Din Memon. Objectives . To introduce the amplifier and its Transfer Characteristics. Opamp Definition, Internal Architecture, Notation, and its Package. Ideal Characteristics of Opamp.

paiva
Download Presentation

DATA ACQUISTION AND SIGNAL PROCESSING

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. DATA ACQUISTION AND SIGNAL PROCESSING Lecture Introduction to Opamps & Multisim Dr. Tayab Din Memon

  2. Objectives • To introduce the amplifier and its Transfer Characteristics. • Opamp • Definition, Internal Architecture, Notation, and its Package. • Ideal Characteristics of Opamp. • Differential Mode of Opamp. • Power of Negative Feedback • Opamp Modes of Operation • Inverting • Non-Inverting • Differential • Session-II Lab Work • Simulation of Modes of Opamp.

  3. DIGITAL PHYSICAL OUTPUT PHENOMENA ANALOG TO SIGNAL SENSOR DIGITAL CONDITIONING CONVERSION Amplifier? Why do we need to amplify signals? To increase level of signals.

  4. Amplifier-Transfer Characteristics • Transfer Characteristic is the relationship between input and output voltages The level of signal amplification is called the Gain, Av, and is the slope of the amplifier transfer characteristics. Input voltage is Vi Output voltage is Vo

  5. How do we build an amplifier? Discrete Devices, Transistors, Resistors, Capacitors. Attractive Solution Use of the Integrated Circuits – Operational Amplifiers(Op-Amp) Inexpensive, Easy to use, and readily available.

  6. How Opamp can be Defined? The op-amp is a high gain dc amplifier that has high input impedance and low output impedance. Note: Op-amps are analog, rather than digital devices, although they are used in many digital instrument. DC Amplifier – An amplifier that is capable of amplifying dc voltages and slowly varying voltages.

  7. Op-Amp Definition • An operational amplifier (op-amp) is a DC-coupled (?)high-gain electronic voltage amplifier with a differential input and, usually, a single-ended output. An op-amp produces an output voltage that is typically hundreds of thousands of times larger than the voltage difference between its input terminals [source: Wikipedia].

  8. DC Coupled • Direct coupled refers to coupling between stages of an amplifier and coupling of the output stage to the load. The reason for coupling devices between stages is to accommodate the different DC biases needed by each stage. Normally you can't just connect the collector output of one stage to the base input of another identical stage, since collector and base operate at very different voltages. So an interstage transformer or capacitor provides DC isolation between stages while passing the audio. • Direct-coupled interstage designs often use complementary stages; a PNP transistor drives an NPN transistor, etc. This makes it much easier to obtain bias compatibility between stages. See ref, figure 2.5.Direct output coupling is used to eliminate the nonlinearity, phase-shift and limited frequency response of a transformer or capacitor. The drawback is the possibility of applying a DC bias to the load. Direct output coupled amplifiers usually have a bias nulling adjustment which may need occasional adjustment.

  9. Internal Structure of Opamp.

  10. Op-amp Notation The Opamp has minimum five terminals: Two Signal Input Terminals: +v and –v One Output terminal vo Two dc Power Supply Terminals +Vcc and –Vcc

  11. Opamp Packages Pin Configuration IC Package Opamp uA741 present in 8pin Dip IC. Also available in different size pins i.e. 16 also.

  12. Opamp Transfer Characteristics…..

  13. For example…… For different inputs and respective outputs the table is provided: n first and second +Vin is more positive then –Vin so Output will be + saturated. In third and fourth –Vin is more positive then +Vin so Output will be - saturated.

  14. Opamp Saturation ……….. Input Signal 30v pk-pk. Output Signal 30V pk-pk Gain 1,000,000 Op-Amp Saturates at 10V

  15. Power of Negative Feedback • Advantages and disadvantages of Negative Feedback: • Less Noise, • Less Disturbance, • High Bandwidth • Gain is decreased Figure: Negative Feedback

  16. Opamp Modes of Operation • Inverting Mode • Noninverting Mode • Differential Mode

  17. Inverting Mode

  18. Non-Inverting Mode

  19. Differential Mode

  20. Voltage Follower

  21. SESSION II LAB WORK All tasks given in the Handout should be completed

  22. Introduction to MultiSim Multisim is fully featured SPICE schematic capture and simulation tool used for circuit design, simulation, and in combination with Ultiboard for layout of custom PCBs.

  23. Design of an amplifier with a gain 10. TASK-I Design an amplifier with gain of 10? Mode choice is open!! Ok! Design using Inverting mode. In inverting mode Voltage gain is ratio of Feedback Resistance to Input Resistance. Vo/Vi= -(Rf/Ri). So Select Rf=10KΩ and Ri=1KΩ, then voltage gain will be 10. HERE IS THE SOLUTION!!

  24. Inverting Amplifier with Gain 10.

  25. WHAT DIFFERENCE DID YOU OBSERVE IN TWO OUTPUTS? ANSWER? Saturation Due to input voltage increase.

  26. Repeat same Task with Non-Inverting Amplifier. In Non-inverting mode Voltage gain is: 1+Rf/Ri. So if we select Rf=4.7KΩ then Ri=0.52KΩ ~0.51K Ω (because 0.51K Ω is a standard Resistor). If we place these values then Output of the Circuit should be 10. HERE IS SOLUTION

  27. Voltage FollowerSimulated Result

  28. Summary • Note that in Inverting and Non-Inverting Opamp modes, feedback is – ve. • The only difference is that; input is applied at different terminals. • Output is 1800 out of phase with input in Inverting whereas in Non-Inverting Output is in phase with Input.

More Related