1 / 33

Advanced LIGO

Advanced LIGO. David Shoemaker NSF Review of Advanced LIGO 11 June 2003. Advanced LIGO. LIGO mission: detect gravitational waves and initiate GW astronomy Next detector Must be of significance for astrophysics

patriciabarrett
Download Presentation

Advanced LIGO

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Advanced LIGO David Shoemaker NSF Review of Advanced LIGO 11 June 2003 LIGO Laboratory

  2. Advanced LIGO • LIGO mission: detect gravitational waves and initiate GW astronomy • Next detector • Must be of significance for astrophysics • Should be at the limits of reasonable extrapolations of detector physics and technologies • Should lead to a realizable, practical, reliable instrument • Should come into existence neither too early nor too late Advanced LIGO LIGO Laboratory

  3. Initial and Advanced LIGO • Factor 10 higher amplitude sensitivity • (Reach)3 = rate • Factor 4 lower frequency bound • NS Binaries: for three interferometers, • Initial LIGO: ~20 Mpc • Adv LIGO: ~350 Mpc • BH Binaries: • Initial LIGO: 10 Mo, 100 Mpc • Adv LIGO : 50 Mo, z=2 • Stochastic background: • Initial LIGO: ~3e-6 • Adv LIGO ~3e-9 LIGO Laboratory

  4. Anatomy of the projected Adv LIGO detector performance • Newtonian background,estimate for LIGO sites • Seismic ‘cutoff’ at 10 Hz • Suspension thermal noise • Test mass thermal noise • Unified quantum noise dominates at most frequencies for fullpower, broadband tuning • Advanced LIGO's Fabry-Perot Michelson IFO is a platform for all currently envisaged enhancements to this detector architecture Initial LIGO 10-22 10-23 10-24 10-25 1 kHz 100 Hz 10 Hz LIGO Laboratory

  5. Design features 40 KG SAPPHIRETEST MASSES ACTIVE ISOLATION QUAD SILICASUSPENSION 180 W LASER,MODULATION SYSTEM PRM Power Recycling Mirror BS Beam Splitter ITM Input Test Mass ETM End Test Mass SRM Signal Recycling Mirror PD Photodiode LIGO Laboratory

  6. Laser 40 KG SAPPHIRETEST MASSES ACTIVE ISOLATION QUAD SILICASUSPENSION LIGO Laboratory

  7. output NPRO QR f f EOM FI BP FI modemaching YAG / Nd:YAG 3x2x6 optics QR f f BP YAG / Nd:YAG / YAG HR@1064 f 2f f 3x 7x40x7 HT@808 20 W Master High Power Slave Pre-stabilized Laser • Require the maximum power compatible with optical materials • 1999 White Paper: 180 W at output of laser, leads to 830 kW in cavities • Stick with Nd:YAG, 1064 nm • Three approaches studied by LSC collaboration – stable/unstable slab oscillator (Adelaide), slab amplifier (Stanford), end-pumped rod oscillator (Laser Zentrum Hannover (LZH)); evaluation concludes that all three look feasible • Choose the end-pumped rod oscillator, injection locked to an NPRO • Protoytping well advanced – ½ of Slave system has developed 87 W LIGO Laboratory

  8. Pre-stabilized laser • Overall subsystem system design similar to initial LIGO • Frequency stabilization to fixed reference cavity, 10 Hz/Hz1/2 at 10 Hz required (???? At ?? Hz seen in initial LIGO) • Intensity stabilization to in-vacuum photodiode, 2x10-9 ΔP/P at 10 Hz required (1x10-8 demonstrated) • Max Planck Institute, Hannover leading the Pre-stabilized laser development – Willke • Close interaction with Laser Zentrum Hannover • Experience with GEO-600 laser, reliability, packaging • Germany contributing laser to Advanced LIGO LIGO Laboratory

  9. Input Optics, Modulation 40 KG SAPPHIRETEST MASSES ACTIVE ISOLATION QUAD SILICASUSPENSION LIGO Laboratory

  10. Input Optics • Provides phase modulation for length, angle control (Pound-Drever-Hall) • Stabilizes beam position, frequency with suspended mode-cleaner cavity • Matches into main optics (6 cm beam) with suspended telescope • 1999 White Paper: Design similar to initial LIGO but 20x higher power • Challenges: • Modulators • Faraday Isolators LIGO Laboratory

  11. Input Optics • University of Florida leading development effort -- Reitze • As for initial LIGO • High power rubidium tantanyl phosphate (RTP) electro-optic modulator developed • Long-term exposure at Advanced LIGO power densities without damage • Faraday isolator from IAP-Nizhny Novgorod • thermal birefringence compensated • Ok to 80 W – more powerful test laser being installed at Livingston LIGO Laboratory

  12. Test Masses 40 KG SAPPHIRETEST MASSES ACTIVE ISOLATION QUAD SILICASUSPENSION 200 W LASER,MODULATION SYSTEM LIGO Laboratory

  13. Test Masses / Core Optics • Absolutely central mechanical and optical element in the detector • 830 kW; <1ppm loss; <20ppm scatter • 2x108 Q; 40 kg; 32 cm dia • 1999 White Paper: Sapphire as test mass/core optic material; development program launched • Low mechanical loss, high density, high thermal conductivity all desirable attributes of sapphire • Fused silica remains a viable fallback option • Significant progress in program • Industrial cooperation • Characterization by very active LSC working group Full-size Advanced LIGO sapphire sample LIGO Laboratory

  14. Core Optics Compensation Polish • Fabrication of Sapphire: • 4 full-size Advanced LIGO boules grown(Crystal Systems); 31.4 x 13 cm; two acquired • Substrate mechanical losses: requirement met • recently measured at 200 million • Bulk Homogeneity: requirement met • Sapphire as delivered has 50 nm-rms distortion • Goodrich 10 nm-rms compensation polish • Polishing technology: requirement met • CSIRO has polished a 15 cm diam sapphire piece: 1.0 nm-rms uniformity over central 120 mm • Bulk Absorption: • Uniformity needs work • Average level ~40 ppm, meets requirements before LIGO Laboratory after

  15. Mirror coatings 40 KG SAPPHIRETEST MASSES ACTIVE ISOLATION COATINGS QUAD SILICASUSPENSION 200 W LASER,MODULATION SYSTEM LIGO Laboratory

  16. Test Mass Coatings • Optical absorption (~0.5 ppm), scatter meetrequirements for (good) conventional coatings • R&D mid-2000: Thermal noise due to coating mechanical loss recognized; LSC programput in motion to develop low-loss coatings • Series of coating runs – materials, thickness, annealing, vendors • Measurements on a variety of samples • 2001: TaO5 identified as principal source of loss • 2002: Test coatings show somewhat reduced loss • Annealed Silica/Alumina • Doped Silica/Tantala • Need ~3x reduction in loss to make compromise to performance minimal • 2003: Expanding the coating development program • RFQ out to 5 vendors; wish to select 2 • Direct measurement via special purpose TNI interferometer – lab tour • First to-be-installed coatings needed in ~2.5 years – sets the time scale Goalcoating Standardcoating LIGO Laboratory

  17. Thermal Compensation 40 KG SAPPHIRETEST MASSES ACTIVE ISOLATION COATINGS QUAD SILICASUSPENSION 200 W LASER,MODULATION SYSTEM LIGO Laboratory

  18. ITM Compensation Plates PRM ITM SRM Active Thermal Compensation • 1999 White Paper: Need recognized, concept laid out • Removes excess ‘focus’ due to absorption in coating, substrate • Allows optics to be used at all input powers • 2002: Initial R&D successfully completed • Quasi-static ring-shaped additional heating • Scan to complement irregular absorption • Sophisticated thermal model (‘Melody’) inuse to calculate needs and solution • 2003: Gingin facility (ACIGA) readying tests with Lab suspensions, optics • Application to initial LIGO in preparation Shielded ring compensator test 20 nm Optical path distortion LIGO Laboratory

  19. Seismic Isolation 40 KG SAPPHIRETEST MASSES ACTIVE ISOLATION COATINGS QUAD SILICASUSPENSION 200 W LASER,MODULATION SYSTEM LIGO Laboratory

  20. Isolation: Requirements • 1999 White Paper: Render seismic noise a negligible limitation to GW searches • Newtonian background will dominate for >10 Hz • Suspension and isolation contribute to attenuation • 1999 White Paper: Reduce or eliminate actuation on test masses • Actuation source of direct noise, also increases thermal noise • Acquisition challenge greatly reduced • In-lock (detection mode) control system challenge is also reduced Seismiccontribution Newtonianbackground LIGO Laboratory

  21. Isolation: Two-stage platform • 2000: Choose an active approach: • high-gain servo systems, two stages of 6 degree-of-freedom each • Allows extensive tuning of system after installation, operational modes • Dynamics decoupled from suspension systems • Lead at LSU – Giaime • 2003: Stanford Engineering Test Facility Prototype coming on line • Mechanical system complete • Instrumentation being installed • First measurements indicate excellent actuator – structure • 2003: RFQ for final Prototypes released LIGO Laboratory

  22. Isolation: Pre-Isolator • External stage of low-frequency pre-isolation ( ~1 Hz) • Tidal, microseismic peak reduction • DC Alignment/position control and offload from the suspensions • 1 mm pp range • Lead at Stanford – Lantz • 2003: Prototypes in test and evaluation at MIT for early deployment at Livingston in order to reduce the cultural noise impact on initial LIGO • System performance exceeds Advanced LIGO requirements LIGO Laboratory

  23. Suspension 40 KG SAPPHIRETEST MASSES ACTIVE ISOLATION COATINGS QUAD SILICASUSPENSION 200 W LASER,MODULATION SYSTEM LIGO Laboratory

  24. Suspensions: Test Mass Quads • 1999 White Paper: Adopt GEO600 monolithic suspension assembly • Requirements: • minimize suspension thermal noise • Complement seismic isolation • Provide actuation hierarchy • 2000: Quadruple pendulum design chosen • Fused silica fibers, bonded to test mass • Leaf springs (VIRGO origin) for verticalcompliance • Success of GEO600 a significant comfort • All suspensions now installed • PPARC proposal: significant financial and technical contribution; quad suspensions, electronics, and some sapphire substrates • U Glasgow, Birmingham, Rutherford • Cantley, Strain, Hough LIGO Laboratory

  25. Suspensions: Triples • Triple suspensions for auxiliary optics • Relaxed performance requirements • 2003: Prototype of Mode Cleaner triple suspension in testing – lab tour • To be installed in LASTI fall-2003 LIGO Laboratory

  26. GW Readout 40 KG SAPPHIRETEST MASSES ACTIVE ISOLATION COATINGS QUAD SILICASUSPENSION 200 W LASER,MODULATION SYSTEM LIGO Laboratory

  27. GW readout, Systems • 1999 White Paper: Signal recycled Michelson Fabry-Perot configuration • Offers flexibility in instrument response, optimization for technical noises • Can also provide narrowband response • Critical advantage: can distribute optical power in interferometer as desired • 2000: Three table-top prototypes give direction for sensing, locking system • 2003: Glasgow 10m prototype: control matrix elements confirmed • 2003: Readout choice – DC rather than RF for GW sensing • Offset ~ 1 pm from interferometer dark fringe • Best SNR, simplifies laser, photodetection requirements • Caltech 40m prototype in construction, early testing – lab tour • Complete end-to-end test of readout, controls, data acquisition LIGO Laboratory

  28. Scope of proposal • Upgrade of the detector • All interferometer subsystems • Data acquisition and control infrastructure • Upgrade of the laboratory data analysis system • Observatory on-line analysis • Caltech and MIT campus off-line analysis and archive • Virtually no changes in the infrastructure • Buildings, foundations, services, 4km arms unchanged • Move 2km test mass chambers to 4km point at Hanford • Replacement of ~15m long spool piece in vacuum equipment • Present vacuum quality suffices for Advanced LIGO LIGO Laboratory

  29. Reference design options • Could just upgrade 2 interferometers • Upgrade of all three interferometers: In discovery phase, • Improvement of sensitivity – roughly doubles the event rate • Allows better stochastic upper limits (co-located instruments) • Improves non-gaussian statistics • Commissioning on other LHO IFO while observing with LHO-LLO pair • In observation phase, the same IFO configuration can be tuned to increase low or high frequency sensitivity • sub-micron shift in the operating point of one mirror suffices • third IFO could e.g., • observe with a narrow-band VIRGO • focus alone on a known-frequency periodic source • focus on a narrow frequency band associated with a coalescence, or BH ringing of an inspiral detected by other two IFOs LIGO Laboratory

  30. Reference design options • Baseline is to upgrade the 3rd interferometer from 2km to 4km • Could leave at 2km • Cost is modest and sensitivity gain supports discovery • Will certainly want maximum sensitivity later • Baseline is effectively a simultaneous upgrade of both sites • Could stagger quite significantly to maintain the network – with an equally significant delay in completion and coincidence observations by the two LIGO sites • Baseline is to employ Sapphire as the test mass material • Fused silica a strong fallback alternative LIGO Laboratory

  31. Timing of Advanced LIGO • Observation of gravitational waves is a compelling scientific goal, and Advanced LIGO will be a crucial element • Qualitative increase in sensitivity over first generation instruments • Strong astrophysical support for Advanced LIGO signal strengths • Delaying Advanced LIGO likely to create a significant gap in the field – at least in the US • Can lose the team of instrument scientists • Running costs of an over-exploited instrument represents lost opportunity • Our LSC-wide R&D program is in concerted motion • Appears possible to meet program goals • We are well prepared • Reference design well established, confirmation growing through R&D • Timely for International partners that we move forward now LIGO Laboratory

  32. Baseline plan • Initial LIGO Observation at design sensitivity 2004 – 2006 • Significant observation within LIGO Observatory • Significant networked observation with GEO, VIRGO, TAMA • Structured R&D program to develop technologies • Conceptual design developed by LSC in 1998 • Cooperative Agreement carries R&D to Final Design, 2005 • Proposal early 2003 for fabrication, installation • Long-lead purchases planned for 2004, real start 2005 • Sapphire Test Mass material, seismic isolation fabrication • Prepare a ‘stock’ of equipment for minimum downtime, rapid installation • Start installation in 2007 • Baseline is a staggered installation, Livingston and then Hanford • Coincident observations by 2010 LIGO Laboratory

  33. Advanced LIGO • Initial instruments, data establishing the field of interferometric GW detection • Advanced LIGO promises exciting astrophysics • Substantial progress in R&D, design • Still a few good problems to solve • A broad community effort, international support • Ready to make transition from R&D to Project • Advanced LIGO can lead the field to maturity LIGO Laboratory

More Related